Safety Rules 1 Unpacking Your Fan 2 Installing Your Fan 3 Setting the Codes 6 Making the Electrical Connections 7 Operating Your Fan 11 Care of Your Fan 12 Troubleshooting 12 Specifications 13 Table of Contents
READ AND SAVE THESE INSTRUCTIONS 1. To reduce the risk of electric shock, insure electricity 2. 3. 4. 5. 6. has been turned off at the circuit breaker or fuse box before beginning. All wiring must be in accordance with the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. CAUTION: To reduce the risk of personal injury, use only the screws provided with the electrical box.
1 7 4 8 2 5 a 10 9 c 3 b d 11 6 Unpack your fan and check the contents. You should have the following items: 1. Mounting Plate (inside canopy) 2. 6” Ball/Downrod Assembly (hanger pin and locking pin pre-attached) 3. Canopy with Canopy Ring (attached) 4. Decorative Motor Collar Cover 7. Blade Brackets (5) 8. Switch Cup Adaptor 9. Light Kit 10. Wire Shade 11. Transmitter and Receiver a. Blade bracket hardware (11 screws) b. Blade attachment hardware (16 screws) c.
Tools Required Figures 1, 2, and 3 are examples of different ways to mount the electrical box. Phillips screw driver or straight slotted screw driver, adjustable wrench, step ladder, and wire cutters. Figure 3 Mounting Options If there isn’t an existing electrical box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the electrical box directly to the building structure. Use appropriate fasteners and building materials.
Hanging the Fan REMEMBER to turn off the power. Follow the steps below to hang your fan properly. NOTE: This fan is recommended for standard ceiling mount using the downrod provided with this fan. When using standard ceiling installation with the 6 inch downrod provided, the distance from the ceiling to the bottom of the fan blades will be approximately 13 inches. Standard Ceiling Mounting 7. Re-tighten the set screws on the collar on top of the motor housing. Turn Canopy Ring to Remove 8.
Installing Fan to the Electrical Box THE HOOK AS SHOWN IN FIGURE 9 IS ONLY TO BALANCE FAN WHILE ATTACHING WIRING. FAILURE TO HANG AS SHOWN IN FIGURE 9 MAY RESULT IN HOOK BREAKING CAUSING THE FAN TO FALL. HOOK MUST PASS FROM INSIDE TO OUTSIDE OF CANOPY. UL Listed Electrical Box WHEN MOUNTING THE FAN ON A SLOPED CEILING, THE STANDARD BALL/DOWNROD MOUNTING METHOD MUST BE USED. THE MOUNTING PLATE MUST BE MOUNTED SO THAT THE SLOT OPENINGS ARE ON THE LOWER SIDE BY SLIDING THE MOUNTING PLATE FROM THE TOP DOWN.
Setting the Codes This unit has 16 different code combinations to prevent possible interference from other remote units such as garage door openers, car alarms or security systems. Transmitter To set the codes, perform the following steps: 1. Setting the code on the transmitter: a. Remove the battery cover from the battery compartment on the back side of the transmitter. ON DIP 1 2 3 4 b. Slide code switches to your choice of up or down position (factory setting is up). Dip Switches c.
Follow the steps below to connect the fan to your household wiring. Use the wire connecting nuts supplied with your fan and supplied with remote control. Secure the connectors with electrical tape. Make sure there are no loose strands or connections. (Figure 11) 1. Connect the ground conductor of the 120v supply (this may be a bare wire or a wire with green colored insulation) to the green ground lead(s) of the fan (Figure 11). 2.
Finishing the Fan Installation STANDARD CEILING MOUNTING WHEN USING THE STANDARD BALL/DOWNROD MOUNTING, THE TAB IN THE RING AT THE BOTTOM OF THE MOUNTING PLATE MUST REST IN THE GROOVE OF THE HANGER BALL. FAILURE TO PROPERLY SEAT THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING. 1. Align the locking slots of the ceiling canopy with the two screws in the mounting plate. Push up to engage the slots and turn clockwise to lock in place. Immediately tighten the two mounting screws firmly. 2.
Blade Balancing All blades are grouped by weight. Because natural woods vary in density, the fan may wobble even though the blades are weight matched. Touching Ceiling The following procedure should correct most fan wobble. Check after each step. 1. Check that all blade screws are secure. 2. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades.
Installing the Switch Cup Cover/Light Kit/ LED Bulbs/Wire Shade CAUTION - To reduce the risk of electrical shock, disconnect the electrical supply circuit to the fan before installing the light kit. 1. Remove one screw from the black bracket from the fan motor assembly. Loosen, but do not remove the other two screws. Align the key hole slots in the switch cup adaptor with the two screws in the black bracket. (Figure 15) 2.
Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans, and so on. LIGHT /DIMMER The fan shipped from the factory with the reversing switch positioned to circulate air downward. If airflow is desired in the opposite direction, turn your fan off and wait for the blades to stop turning, then slide the reversing switch (located at the top of the motor housing, refer to figure 16 on page 10) to opposite position, and turn fan on again.
Care of Your Fan Troubleshooting 1. Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) Fan will not start Here are some suggestions to help you maintain your fan. 2. Clean your fan periodically to help maintain its new appearance over the years.
FAN SIZE 54” SPEED Low Med High VOLTS 120 FAN POWER CONSUMPTION AIRFLOW (WITHOUT LIGHTS) CFM WATTS 11 31 65 1649 3240 4794 AIRFLOW EFFICIENCY (HIGHER IS BETTER) CFM/WATT 150 105 74 NET WEIGHT 21.38 Lbs GROSS CUBE WEIGHT FEET 24.25 Lbs 2.4 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Manual de instalación del ventilador de techo
Normas de seguridad 1 Cómo desempacar el ventilador 2 Cómo instalar el ventilador 3 Configurando los Códigos 6 Cómo hacer las conexiones eléctricas 7 Cómo usar el ventilador 11 Cuidado del ventilador 12 Solución de problemas 12 Especificaciones 13 Tabla de contenido
LEE Y GUARDA ESTAS INSTRUCCIONES 1. Para disminuir el riesgo de descarga eléctrica, antes de comenzar la instalación asegúrate de que la electricidad ha sido cortada en el cortacircuitos o en la caja de fusibles. 2. Todo el cableado tiene que cumplir con el Código Nacional de Electricidad ANSI/NFPA 70-1999 y con los códigos locales de electricidad. La instalación eléctrica debe hacerse por un electricista calificado y con licencia. 3.
1 7 4 a 10 8 2 5 9 c 3 b d 11 6 Desempaca tu ventilador y revisa el contenido. Debes tener los siguientes artículos: 1. Soporte de montaje (dentro de la cubierta) 6. Aspas (5) 2. Conjunto de tubo bajante/bola de 15.2 cm (pasadores de soporte y de cierre prefijados) 7. Soporte del aspa (5) 3. Cubierta con aro de cubierta (acoplado) 4. Cubierta decorativa del collarín del motor 5. Conjunto motor-ventilador 8. Adaptador de la caja del interruptor 9. Kit de Luces 10. Pantalla de Alambre 11.
Herramientas necesarias Las figuras 1, 2 y 3 ejemplifican diferentes maneras de montar la caja eléctrica. Destornillador Phillips o de punta plana, llave ajustable, escalera de tijera y cortacables. Placa de montaje en techo Caja eléctrica empotrada Opciones de montaje Figura 3 Si no hay una caja eléctrica presente, lee las siguientes instrucciones. Desconecta la energía retirando los fusibles o apagando los cortacircuitos.
Cómo colgar el ventilador RECUERDA cortar el suministro de electricidad. Sigue los pasos más abajo para colgar correctamente tu ventilador. NOTA: Se recomienda instalar este ventilador en techo interior estándar usando el tubo bajante incluido. Cuando uses una instalación de techo estándar con el tubo bajante de 6 plg (15.2 cm) suministrado, la distancia desde el techo a la parte inferior de las aspas será de unas 13 plg (33 cm). Montaje estándar en techo 7.
Cómo instalar el ventilador en la caja eléctrica PRECAUCIÓN EL GANCHO, COMO SE MUESTRA EN LA FIGURA 9, SOLAMENTE ES PARA SOSTENER EL VENTILADOR MIENTRAS SE CONECTAN LOS CABLES. SI NO SE CUELGA COMO SE MUESTRA EL LA FIGURA 9, PUEDE ROMPERSE EL GANCHO Y EL VENTILADOR SE CAÉRA. EL GANCHO DEBE PASAR DE ADENTRO HACIA FUERA LA CUBIERTA Caja eléctrica aprobada por UL PRECAUCIÓN CUANDO MONTES EL VENTILADOR EN UN TECHO INCLINADO, DEBES USAR EL MÉTODO DE MONTAJE CON TUBO BAJANTE Y BOLA ESTÁNDAR.
Cómo configurar los códigos Esta unidad tiene 16 combinaciones de códigos diferentes para prevenir una posible interferencia de otras unidades de control remoto, como aquellas de puertas de garajes, alarmas de vehículos o sistemas de seguridad. Transmisor Para configurar un código, ejecuta los siguientes pasos: ON 1. Cómo configurar el código del transmisor: DIP 1 2 3 4 a. Quita la cubierta del compartimento de las baterías en la parte posterior del transmisor. Interruptores Dip b.
7. NEGRO BLACK BLANCO WHITE BLANCO AZUL Receptor Remote remoto Receiver Conductor Grounding aConductor tierra BLANCO VERDE Sigue estos pasos para conectar tu ventilador al circuito de tu hogar. Usa las tuercas de conexión de cable incluidas con el ventilador y el control remoto. Asegura los conectores con cinta aislante. Asegúrate de que no haya conexiones ni cables sueltos. (Figura 11) 1.
Cómo finalizar la instalación del ventilador MONTAJE ESTÁNDAR EN TECHO ADVERTENCIA EN EL MONTAJE ESTÁNDAR DE TUBO BAJANTE Y BOLA, LA PESTAÑA EN EL ARO DE LA PARTE INFERIOR DE LA PLACA DE MONTAJE TIENE QUE ENCAJAR EN LA RANURA DE LA BOLA DE SOPORTE. SI NO ENCAJA BIEN, PUEDE DAÑARSE EL CABLEADO. 1. Alinea las ranuras de cierre de la cubierta de techo con los dos tornillos de la placa de montaje. Empuja hacia arriba para enganchar las ranuras y gira de izquierda a derecha para asegurarlas en su lugar.
Cómo equilibrar las aspas Todas las aspas se agrupan por peso. Puesto que las maderas naturales varían en densidad, el ventilador puede oscilar aunque las aspas tengan el mismo peso. El siguiente procedimiento corregirá en gran medida la oscilación del ventilador. Verifica después de cada paso. 1. Verifica que todos los tornillos de las aspas estén asegurados. 2. La mayoría de los problemas de oscilación del ventilador se deben a que las aspas no están al mismo nivel.
Cómo instalar la cubierta de la caja del interruptor/ kit de luces/bombillas LED/ pantalla de alambre PRECAUCIÓN - Para disminuir el riesgo de descarga eléctrica, desconecta el circuito de suministro de energía al ventilador antes de instalar el kit de luces. Conector de enchufe superior 1. Quita un tornillo del soporte negro del conjunto motor-ventilador. Afloja los otros dos tornillos, sin quitarlos.
Las configuraciones de velocidad para clima cálido o frío dependen de factores como el tamaño de la habitación, la altura del techo, la cantidad de ventiladores y otras. Este ventilador se envía desde la fábrica con el interruptor de reversa en posición de hacer circular el aire hacia abajo.
Cuidado del ventilador Aquí tienes algunas sugerencias para dar mantenimiento a tu ventilador. 1. Por causa del movimiento natural del ventilador, algunas conexiones pueden aflojarse. Revisa las conexiones de soporte, los soportes y los accesorios de aspas dos veces al año. Comprueba que estén seguros. (No es necesario desmontar el ventilador del techo). 2. Limpia el ventilador con frecuencia para que luzca como nuevo al paso de los años.
TAMAÑO DEL VENTILADOR 54” VELOCIDAD Baja Media Alta VOLTIOS (V) 120 CONSUMO DE ENERGÍA DEL VENTILADOR (SIN LAS LUCES) EN WATTS FLUJO DE AIRE PIES3/M (MÁS ALTO ES MEJOR) 31 65 1649 3240 4794 150 11 EFICIENCIA DE FLUJO DE AIRE PIES3 POR MINUTO/W 105 74 PESO NETO PESO BRUTO PIES CÚBICOS 21.38 Lb 24.25 Lb 2.4 Este equipo fue sometido a prueba y se determinó que cumple con los límites establecidos para un dispositivo digital Clase B según la Parte 15 de las Normas FCC.