Pager User Manual

DIN Rear-mount
Installation using the screw holes on the side of the unit
1. Remove the frame. (Fig. 8)
Fig. 8
2. Fastening the unit to the factory radio mounting bracket.
(Fig. 9) (Fig. 10)
Select a position where the screw holes of the bracket and
the screw holes of the head unit become aligned (are fitted),
and tighten the screws at 2 places on each side. Use either
truss screws (5 × 8 mm) or flush surface screws
(5 × 9 mm), depending on the shape of the screw holes in
the bracket.
Fig. 9
Fig. 10
11
13
12
10
Frame
Insert the release pin into the hole in
the bottom of the frame and pull out
to remove the frame.
(When reattaching the frame, point
the side with a groove downwards
and attach it.)
Installation <ENGLISH>
Screw
Dashboard or Console
Factory radio mounting bracket
Fixing the front panel
If you do not operate the removing and attaching the front panel function, use the supplied
fixing screws and holders to fix the front panel to this unit.
1. Attach the holders to both sides of the front panel. (Fig. 11)
Fig. 11
2. Replace the front panel to the unit. (Fig. 12)
Fig. 12
3. Flip the holders into upright positions. (Fig. 13)
Fig. 13
4. Fix the front panel to the unit using fixing screws. (Fig. 14)
Fig. 14
Fixing screw
Installing the Unit on a Left-Hand-
Drive Car
Note:
• When the unit is installed on a right-hand-drive
car, the horizontal positions are inverted.
1. Secure inner holder to the inner cir-
cumference of the steering wheel
with belt. (Fig. 16)
• Fit the inner holder to the steering wheel so
that the arrow-marked side faces the driver as
shown below.
Fig. 16
2. Cut the extra portion of the belt at
the center of the inner holder.
(Fig. 17)
Fig. 17
3. Install outer holder on the inner
holder and secure with screws.
(Fig. 18)
• Tighten the screws with the supplied hexago-
nal wrench.
Fig. 18
4. Install the remote control unit in the
holder. (Fig. 19)
• When removing the remote control unit from
the holder, move the corrugated release sec-
tion toward the steering wheel and slide the
remote control unit toward you.
Fig. 19
Installing the Steering Remote Control Unit <ENGLISH>
WARNING
• Avoid installing this unit in such a location where
the operation of safety devices such as airbags is
prevented by this unit. Otherwise, there is a danger
of a fatal accident.
• Avoid installing this unit in such a location where
the operation of the steering wheel and the
gearshift lever may be prevented. Otherwise, it
may result in a traffic accident.
CAUTION
• Installation of this unit requires specialized skills
and experience. Installation of this unit should be
entrusted to a dealer from whom you purchased
this unit.
• Install this unit using only the parts supplied with
this unit. If other parts are used, this unit may be
damaged or could dismount itself, which leads to
an accident or trouble.
• Install this unit as required by this manual. Failure
to do so may cause an accident.
• Do not install this unit near the doors where rain-
water is likely to be spilled on the unit. Incursion
of water into the unit may cause smoke or fire.
WARNING
• Fix this unit securely to the steering wheel with the
belt attached to the unit. If this unit is loose, it dis-
turbs driving stability, which may result in a traffic
accident.
• Do not attach this unit to the outer circumference
of the steering wheel. Otherwise, it disturbs dri-
ving stability, causing a traffic accident. Always
attach this unit to the inner circumference of the
steering wheel as shown. (Fig. 15)
Note:
• Do not install this unit in such a place as may
obstruct the driver’s view.
• Since interior layout differs depending on the type
of vehicle, the ideal installation location for the
unit also differs. When installing the unit, select a
location that assures optimum transmission of sig-
nals from the unit to the car stereo.
Fig. 15
Belt
Inner holder
Screw
Outer holder
Release Section
XRD7051A_N 03.10.6 3:41 PM Page 9