Specification Sheet

Description
The 3M
™
Protective Coverall 4510 is designed to help protect against certain
light liquid splashes (Type 6) and hazardous dusts (Type 5).
The key features include:
• Constructed of quality laminated microporous material
• Elasticized waist, ankles, and wrists for convenience and freedom
of movement
• Two-way zipper with storm flap
• Low-linting
• Anti-static coating on both sides
Materials
• Suit: Polypropylene/Polyethylene Laminate Film, White
• Zipper: Nylon on Polyester Braid
• Elastic: Neoprene Rubber
• Thread: Polyester
• Basis Weight: 47 grams/m
2
This product does not contain components made from silicone or natural
rubber latex.
Approvals
CE approved under PPE Directive (89/686/ECC), Category III.
Article 10 Certification: BTTG Testing & Certification Ltd. Notified Body Number:
0338. Article 11B Supervision: SGS United Kingdom, LTD.
Notified Body Number: 0120.
Comfort and Protection
* In the whole suit test, liquid spray is applied to the subject for 1 minute. During this time the subject moves gently
and is rotated through 360°. A total of 1.88 liters is sprayed from four nozzles. The clothing is allowed to drain
for 2 minutes and then the absorbent coverall is inspected for stains which are compared to a calibration stain.
Requirement: Passes when the stained area inside is smaller than 3 times the calibration stain area.
** All apparel must be suitably grounded for anti-static treatment to be effective. Electrostatic propensity may decrease
with wearing time and/or severe conditions.
*** Except puncture resistance.
Applications and Performance
* For additional chemical penetration and repellency data, please contact your local 3M Technical Service Representative.
3M
™
Protective Coverall 4510
Technical
4510
Data Sheet
Typical Applications
Typical applications may include asbestos inspection, coal dust in power plants,
metal polishing, light-duty building cleaning, machine or vehicle maintenance,
paint spraying, pharmaceutical, general industrial clean-up, insulation
installation, general powder handling and food processing.
In all cases a risk assessment should be carried out. Users must be trained and
have read all User Instructions. Use limitations and performance data should
be considered to ascertain the protection required. If in doubt, contact a safety
professional.
Performance
The table below shows the performance of this product when tested under
laboratory conditions. Please note that the tests may not reflect the reality of
use and do not account for factors such as excessive heat and mechanical wear.
* The standards EN 13034:2005 and EN ISO 13982-1:2004, and EN 1073-2:2002 dene performance classes.
** The maximum Class is 6 unless otherwise noted.
*** The European Standard EN ISO 6530 measures liquid penetration through a fabric and liquid repellency by a fabric.
The test simulates exposure to small amounts of chemicals (10 ml) for 1 minute duration only. The penetration index
refers to the percentage of the original quantity which penetrates the fabric within 1 minute (in a detector beaker) as a
percentage of the original quantity.
Liquid Protection Type 6 (EN 13034). Whole suit reduced spray test (EN ISO 17491-4-2008)*
Dust Protection
Type 5 (EN ISO 13982-1:2004). Inward Leakage results:
L
jmn,82/90
< 30 %; L
S,8/10
< 15 %.
Anti-static Anti-static coating on both sides (EN 1149-1:2006/ EN 1149-5:2008)**
Nuclear
Radioactive particulates (EN 1073-2:2002), Class 1***. Does not offer
protection against radiation.
Non-Hazardous Particulates Yes Hazardous Liquid Splash No*
Non-Hazardous Liquid Splash Yes Hazardous Liquid Spray No
Hazardous Dusts and Fibers Yes Organic Solvents No
Liquid Continuous
Contact/Immersion
No Acids/Alkalis
Yes, if chemical is
compatible with
suit material*
Gases and Vapors No
Test Standard Result Standard*
Class**/
Result
Abrasion
ASTM D4157
Cycles to Rupture
1000 EN 530 Class 1
Flex Cracking ISO 7854 Class 5
Tear Resistance Trapezoidal
ASTM D5733 (warp
direction/ll direction)
11 lbf / 5 lbf ISO 9073-4 Class 1
Tensile Strength
ASTM D751, Section 11,
Procedure A (longitude/
traverse)
12 lbs / 20 lbf ISO 13934-1 Class 1
Puncture Resistance ASTM D2582 (MD/CD) 36N / 25N EN 863 Class 1
Bursting Resistance ASTM D751, Section 18 80N ISO 13938-1 Class 1
Resistance to Ignition CPSC 16 CFR PT 1610 Class 1 EN 13274-4 Pass
Seam Strength
ASTM D751, Section 66
(Peak Load/Seam Strength)
8 lbf / 4 lbf/in EN ISO 13935-2 Class 1
Hydrostatic Resistance ASTM D751, Procedure B 1185 mm
Repellency to Liquids*** –
30% H
2
SO
4
EN ISO 6530 Class 3 of 3
Liquid Penetration
Resistance*** – 30% H
2
SO
5
EN ISO 6530 Class 3 of 3
Repellency to Liquids*** –
10% NaOH
EN ISO 6530 Class 3 of 3
Liquid Penetration
Resistance*** – 10% NaOH
EN ISO 6530 Class 3 of 3
Anti-static Coating on
Both Sides
EN 1149-1:2006/
EN 1149-5:2008
Pass
Radioactive Particulates EN 1073-2 Class 1 of 3