LCD Display ACD-515D ACD-515D 15.
LCD Display ACD-515D Copyright Notice This document is copyrighted, 2011. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
LCD Display ACD-515D Acknowledgments Intel® is registered trademarks of Intel® Corporation. IBM, PC/AT, PS/2 are trademarks of International Business Machines Corporation. Microsoft® Windows is a registered trademark of Microsoft® Corporation. RTL is a trademark of Realtek Semi-Conductor Co., Ltd. C&T is a trademark of Chips and Technologies, Inc. UMC is a trademark of United Microelectronics Corporation. ITE is a trademark of Integrated Technology Express, Inc.
LCD Display ACD-515D Packing List The LCD monitor comes with the following standard parts shown as below. Check and make sure they are included and in good condition. If anything is missing or damaged, contact the dealer immediately.
LCD Display ACD-515D Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
LCD Display ACD-515D 14. If any of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the users manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15.
LCD Display ACD-515D Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Display 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 外壳 × ○ ○ ○ ○ ○ 液晶模块 × ○ ○ ○ ○ ○ 触控模块 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期限，系指在一般正常使用状况下。 二、上述部件物质触控模块为选购品。 vi
LCD Display ACD-515D Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 General Specification ................................................ 1-4 1.4 Dimension ................................................................. 1-6 Chapter 2 Hardware Installation 2.1 Before Unpacking...................................................... 2-2 2.
LCD Display ACD-515D The MENU Keys.............................................................. 3-7 3.7 RGB Color- Submenu. .............................................. 3-8 3.8 Language- Submenu................................................. 3-9 3.9 Auto Config- Submenu.............................................. 3-10 3.10 Mode Resolution- Submenu Chapter...................... 3-11 3.11 Exit Menu- Submenu...............................................
LCD Display ACD-515D Chapter 1 General Information Chapter 1 General Information 1-1
LCD Display ACD-515D 1.1 Introduction Thank you for purchasing of the Industry Display Panel TFT LCD monitor - a marvelous contribution of cutting-edge technology. The LCD monitor has been designed with serious thoughts to present the best performance for most applications. Symbol of elegance, its compact and slim profile are well suited in working locations where space is at a premium. The TFT LCD monitor displays sharper, more brilliant, crisper and flicker-free images.
LCD Display ACD-515D 1.2 Features 15.
LCD Display ACD-515D 1.3 General Specification Type Color TFT Size 15.6" TFT LCD Construction Plastic front bezel and steel back chassis Mounting VESA/ Wallmount Input signal VGA, DVI Control OSD (On Screen Display) on the panel Power Supply External power adapter Dimension 15.51” (W) x 10.71”(H) x 2.36”(D) (394mm x 272mm x 59mm Gross Weight 14.3 lb (6.5 Kg) Power Input 12V DC, 5A Brightness 300 cd/m2 (TYP.
LCD Display Light ACD-515D >90% (Pure) transmission Controller USB interface Environmental Operating 32°F~ 104°F (0°C to 40°C) temperature Storage -4°F~ 158°F (-20°C to 70°C) Temperature Storage 5~90% @ 40°C, non-condensing Humidity Vibration 1g rms/5-500Hz/random operation Shock 20 G peak acceleration (11 msec.
LCD Display 1.
LCD Display ACD-515D Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
LCD Display ACD-515D 2.1 Before Unpacking It is very important to place the LCD Display in a suitable environment. The surface for placing the LCD Display should be stable and level. Make sure the place has good ventilation, and out of direct sunlight; away form sources of excessive dust, dirt, heat, water, moisture and vibration. Convenience for connecting the LCD Display the related facilities should be well considered too.
LCD Display ACD-515D 2.2 Connecting Power To power on the LCD Display, use the provided AC-DC adapter and the power cord to connect to the power output socket of the monitor. Fasten the connector securely.
LCD Display ACD-515D 2.3 Connecting to the Computer Turn off the computer and the LCD Display before connecting. Use the Monitor-to-PC VGA、DVI cable to connect the LCD Display to your computer. The cable heads are the same on either side. Fasten the connectors securely.
LCD Display ACD-515D 2.4 VGA Port Connector This DB-15 connector can be connected to the system via the external 15-pin DB-15 connector through the I/O from this unit. Pin Signal Pin Signal 1 Red 2 Green 3 Blue 4 N.C. 5 GND 6 GND 7 GND 8 GND 9 N.C. 10 GND 11 N.C.
LCD Display ACD-515D 2.5 DVI Port Connector Connecting a standard DVI-D connector through I/O port of this unit. This connector supports digital signals only Pin Signal Pin Signal 1 N.C. 2 TMDS Data 2+ 3 TMDS Data 2/4 shield 4 TMDS Data 4- 5 TMDS Data 4+ 6 DDC clock 7 DDC data 8 N.C.
LCD Display ACD-515D 2.6 Serial Port Connector For Touch Screen This pin definition of the connector will be referred when a touch screen has been installed. It must be connected to the RS-232 port of the PC. The touch screen cable is included with all orders which include the optional RS-232 Touch Screen.
LCD Display ACD-515D 2.7 Mini USB Connector For Touch Screen This pin definition of the connector will be referred when a touch screen has been installed. It must be connected to the Mini USB port of the PC. The touch screen cable is included with all orders which include the optional Mini USB Touch Screen. Pin Signal Pin Signal 1 +5V 2 DATA (-) 3 DATA (+) 4 N.C.
LCD Display ACD-515D 2.8 VESA Wall Mounting Mounting the LCD Display with UL Listed Wallmount Bracket only. The LCD Display can be mounted on a monitor arm or wallmount plate. Caution: When mounting the LCD Display, take care to tighten the retention screws or bolts until fully secured, but do not over tighten. Over tighting the retention screws or bolts may cause them to become stripped, rendering them useless.
LCD Display ACD-515D VESA Mounting Holes To mount the LCD Display onto a monitor arm or wallmount plate, please follow the steps below. Step 1: Line up the threaded holes on the monitor rear panel with the screw holes on the monitor arm or wallmount plate. Step 2: Secure the monitor to the arm or stand with the retention screws supplied with the monitor arm or stand.
LCD Display ACD-515D Chapter 3 On Screen Display Control Chapter 3 On Screen Display Control 3-1
LCD Display ACD-515D 3.1 On Screen Display (OSD) Board Description Buttons Description Turn the monitor power ON or OFF. Activate the OSD menu. Enter/confirm the selected option. Move the selector to the next option. UP / Right / Increase / Increase the gauge value of the Input select selected option. Power Menu / Enter Down/ Left / Decrease Change input source. Move the selector to the previous option. Decrease the gauge value of the selected option.
LCD Display ACD-515D 3.
LCD Display ACD-515D 3.
LCD Display ACD-515D 3.
LCD Display ACD-515D 3.
LCD Display ACD-515D 3.
LCD Display ACD-515D 3.
LCD Display ACD-515D 3.
LCD Display ACD-515D 3.
LCD Display ACD-515D 3.
LCD Display ACD-515D 3.
LCD Display ACD-515D Chapter 4 Touch Screen Driver Installation Chapter 4 Touch Screen Driver Installation 4-1
LCD Display ACD-515D 4.1 Introduction The optional ACD-515D Series touch screen uses Projected Capacitive Multi-Touch technology to provide more accurate sensing capacity than other technologies. The touch screen is specially designed for infotainment environments, and has been approved by FCC Class A standards. 4.2 Installing Driver for Windows® XP/ Windows® 7 / Linux The touch screen has drivers for Windows® XP、 Windows® 7 and Linux .
LCD Display ACD-515D 1-3. Select Terminal 1-4. Input Commandsu and System Password 2.
LCD Display ACD-515D 2-1 Input commandls (This is the lowercase L) 2-2 all files of desktop will appear in window. (Please copy the driver on desktop first.) 2-3 Input commandcd eGTouch_v1.00.0726.
LCD Display ACD-515D 2-4 Input commandls (This is the lowercase L) 2-5 The information of the folder, “eGTouch_v1.00_0726.L-x32”, would appear in the window.
LCD Display ACD-515D 3. Reboot 4. Change the permission Input commandchmod△777△/etc/eGTouchd.ini 5. Select Computer (You can modify the value of the Y axis to reverse action principle.
LCD Display ACD-515D 6. Select “File System” 7. Select the “etc” folder 8. Select the “eGTouchd.
LCD Display ACD-515D 9. Select “Display” 10.
LCD Display ACD-515D 11. Execute “Save” Note: If you want to change X or Y axis, please refer to the description of “Direction” as red circle below. 12.
LCD Display ACD-515D 13 . Input command./eGTouch (Execute Driver) and select the file of “eGTouch32”. 13-1. Input command./EventTest (Execute AP) 14. Draw and test (Drawing、Writing) 15. If you want to replace the Interface, please remove the Touchd Driver Input commandsh setup.sh uninstall (Must Under eGTouch_v1.00.0726.
LCD Display ACD-515D 16.
