Multi-Touch Panel PC ACP-5185 ACP-5185 ® 18.
Multi-Touch Panel PC ACP-5185 Copyright Notice This document is copyrighted, 2013. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Multi-Touch Panel PC ACP-5185 Acknowledgments Intel®, CoreTM are registered trademarks of Intel® Corporation. Microsoft® Windows is a registered trademark of Microsoft® Corporation. RTL is a trademark of Realtek Semi-Conductor Co., Ltd. C&T is a trademark of Chips and Technologies, Inc. UMC is a trademark of United Microelectronics Corporation. ITE is a trademark of Integrated Technology Express, Inc. All other product names or trademarks are properties of their respective owners.
Multi-Touch Panel PC ACP-5185 Packing List Before you begin installing your Panel PC, please make sure that the following items have been shipped: ACP-5185 Infotainment Multi-Touch Panel PC HDD screws Product DVD Contains User’s Manual (in PDF format), Drivers and Utilities If any of these items are missing or damaged, you should contact your distributor or sales representative immediately.
Multi-Touch Panel PC ACP-5185 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Multi-Touch Panel PC ACP-5185 14. If any of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15.
Multi-Touch Panel PC ACP-5185 Classification 1. Degree of production against electric shock: not classified 2. Degree of protection against the ingress of water: IPX0 3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide. 4. Mode of operation: Continuous 5.
Multi-Touch Panel PC ACP-5185 FCC This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
Multi-Touch Panel PC ACP-5185 UL Module Description ACP-5185 AC modules are developed to suitable for the Classification Mark requirement viii
Multi-Touch Panel PC ACP-5185 Safety Symbol Description The following safety symbols are further explanations for your reference. Medical equipment with respect to electric shock, fire and mechanical hazards only in accordance with UL 60601-1, and CAN/CSA C22.2 NO. 601.1 Attention, consult ACCOMPANYING DOCUMENTS. Ground wire Protective Ground wire. Medical equipment with respect to electric shock, fire and mechanical hazards only in accordance with UL 60601-1, and CAN/CSA C22.2 NO. 601.
Multi-Touch Panel PC ACP-5185 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Panel PC/ Workstation 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 液晶模块 × ○ ○ ○ ○ ○ 光驱 × ○ ○ ○ ○ ○ 触控模块 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量
Multi-Touch Panel PC ACP-5185 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specification .............................................................. 1-4 1.4 General Information................................................... 1-7 Chapter 2 Hardware Installation 2.1 Safety Precautions ..................................................
Multi-Touch Panel PC ACP-5185 B.3 IRQ Mapping Chart ..............................................B-5 B.4 DMA Channel Assignments...................................B-5 Appendix C Miscellanea C.1 General Cleaning Tips .......................................... C-2 C.2 Cleaning Tools...................................................... C-3 C.3 Scrap Computer Recycling ................................. C-5 C.4 Installing Accessories ...........................................
Multi-Touch Panel PC ACP-5185 Chapter 1 General Information Chapter 1 General Information 1-1
Multi-Touch Panel PC ACP-5185 1.1 Introduction The ACP-5185 is a Multi-Touch Infotainment Panel PC with superior onboard Intel® Core™ i7/i5 processor-based computer. It is a PC-based system with 18.5” true color TFT LCD display, integrated multimedia functions make them the perfect platforms to build comprehensive lifestyle computing applications. The ACP-5185 includes all the features of a powerful computer into a slim and attractive chassis.
Multi-Touch Panel PC ACP-5185 1.2 Features 18.
Multi-Touch Panel PC ACP-5185 1.3 Specification System Processor Onboard Intel® Core i7/i5 Processor System Memory DDR3 SODIMM x 1, Max. 4 GB LCD / CRT Controller Integrated graphics in Intel® QM57 I/O Port USB2.0 x 6 (2 on side; 4 on rear) RS-232 x 1 Line-out x 1 VGA x 1 Storage Disk Drive 2.
Multi-Touch Panel PC ACP-5185 Net Weight 15.4 lb (7 kg) Gross Weight 19.8 lb (9 kg) Environmental Operating Temperature 32oF~104oF (0oC~40oC) (Ambient With Airflow) Storage Temperature -4oF~140oF (-20oC~60oC) Storage Humidity 10%~95% @ 40oC, non-condensing Vibration 1 g rms/ 5-500Hz/ Random Operation (HDD) Shock 20 G peak acceleration (11 msec.
Multi-Touch Panel PC Backlight MTBF (Hours) ACP-5185 50,000 Touchscreen Type Projected Capacitive Multi-Touch (Windows® 7) Light Transmission 90% Lifetime (times) --- Chapter 1 General Information 1-6
Multi-Touch Panel PC ACP-5185 1.4 General Information 1.
Multi-Touch Panel PC VESA 100 Mounting Holes Mounting Holes Chapter 1 General Information 1-8 ACP-5185
Multi-Touch Panel PC ACP-5185 RS-232 Line-out Power Input Power Switch VGA Smart Card Reader (Optional) USB x 4 USB x 2 LAN x 2 Antenna (Optional) Antenna (Optional) Chapter 1 General Information 1-9
Multi-Touch Panel PC ACP-5185 Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
Multi-Touch Panel PC ACP-5185 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Multi-Touch Panel PC ACP-5185 2.
Multi-Touch Panel PC ACP-5185 I/O Cable Cover (Optional) Note 1: You may turn on the power by cutting and destroying the protective cover as it shows below.
Multi-Touch Panel PC ACP-5185 Note 2: The “Anti-Drop Kit” can help on preventing the cable drop from the connector Chapter 2 Hardware Installation 2-5
Multi-Touch Panel PC ACP-5185 2.3 2.
Multi-Touch Panel PC ACP-5185 Step 3: Remove HDD Bracket (4 screws) Step 4: Get the HDD and HDD Bracket ready Chapter 2 Hardware Installation 2-7
Multi-Touch Panel PC ACP-5185 Step 5: Fasten the four screws to fix HDD Bracket and HDD Step 6: Connect the SATA and power cables to the HDD and fasten the four screws to fix the HDD Bracket Chapter 2 Hardware Installation 2-8
Multi-Touch Panel PC AEC-5185 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Multi-Touch Panel PC AEC-5185 3.1 System Test and Iinitialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration stored in the CMOS memory and BIOS NVRAM.
Multi-Touch Panel PC AEC-5185 3.2 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM and BIOS NVRAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Multi-Touch Panel PC Setup Menu Setup submenu: Main Chapter 3 AMI BIOS Setup 3-4 AEC-5185
Multi-Touch Panel PC AEC-5185 Setup submenu: Advanced Options summary: Launch 82577 PXE Disabled OpROM Enabled En/Disable Legacy Boot Option for 82577. Launch 82574 PXE Disabled OpROM Enabled En/Disable Legacy Boot Option for 82574.
Multi-Touch Panel PC AEC-5185 PCI Subsystem Setting Options summary: PCI Latency Timer 32 PCI Bus Clocks Optimal Default, Failsafe Default 64 PCI Bus Clocks 96 PCI Bus Clocks 128 PCI Bus Clocks 160 PCI Bus Clocks 192 PCI Bus Clocks 224 PCI Bus Clocks 248 PCI Bus Clocks Value to be programmed into PCI Latency Timer Register Chapter 3 AMI BIOS Setup 3-6
Multi-Touch Panel PC AEC-5185 ACPI Settings Options summary: Enable ACPI Auto Disabled Optimal Default, Failsafe Default Configuration Enabled Enables or Disables BIOS ACPI Auto Configuration Enable Hibernation Disabled Enabled Optimal Default, Failsafe Default Enables or Disables System ability to Hibernate (OS/S4 Sleep State). This option may be not effective with some OS.
Multi-Touch Panel PC AEC-5185 S5 RTC Wake Settings (Fixed Time) Options summary: Wake system with Disabled Optimal Default, Failsafe Default Fixed Time Enabled En/Disable System wake on alarm event. When enabled, System will wake on the hr:min:sec specified Wake up day 0-31 Default 0 Select 0 for daily system wake up, 1-31 for witch day of the moth that you would like the system to wake up.
Multi-Touch Panel PC AEC-5185 S5 RTC Wake Settings (Dynamic Time) Options summary: Wake system with Disabled Optimal Default, Failsafe Default Dynamic Time Enabled En/Disable System wake on alarm event.
Multi-Touch Panel PC AEC-5185 CPU Configuration Options summary: Hyper-Threading Disabled Enabled Optimal Default, Failsafe Default Enabled for Windows XP and Linux (OS optimized for Hyper-Threading Technology) and Disabled for other OS (OS not optimized for Hyper-Threading Technology). When Disabled only one thread per enabled core is enabled.
Multi-Touch Panel PC AEC-5185 IDE Configuration (IDE) Chapter 3 AMI BIOS Setup 3-11
Multi-Touch Panel PC IDE Configuration (AHCI) Chapter 3 AMI BIOS Setup 3-12 AEC-5185
Multi-Touch Panel PC AEC-5185 IDE Configuration (RAID) Options summary: SATA Mode Disable IDE Optimal Default, Failsafe Default AHCI RAID IDE: Configure SATA controllers as legacy IDE AHCI: Configure SATA controllers to operate in AHCI mode RAID: Configure SATA controllers to operate in RAID mode Serial-ATA Controller # Disabled Enhanced Optimal Default, Failsafe Default Enable/Disable Serial ATA Controller Port # Hot plog Disabled Optimal Default, Failsafe Default Enabled SATA Ports Hot Plug Support Ex
Multi-Touch Panel PC Intel IGD SWSCI OpRegion Chapter 3 AMI BIOS Setup 3-14 AEC-5185
Multi-Touch Panel PC AEC-5185 Options summary: DVMT/FIXED Memory 128MB 256MB Optimal Default, Failsafe Default Maximum Select DVMT/FIXED Mode Memory size used by Internal Graphics Device IGD – Boot Type VBIOS Default CRT LVDS CRT + LVDS Optimal Default, Failsafe Default Select the Video Device which will be activated during POST. This has no effect if external graphics present.
Multi-Touch Panel PC AEC-5185 USB Configuration Options summary: Device Name (Emulation Type) Auto Optimal Default, Failsafe Default Floppy Forced FDD Hard Disk CDROM If Auto. USB devices less than 530MB will be emulated as Floppy and remaining as Floppy and remaining as hard drive. Forced FDD option can be used to force a HDD formatted drive to boot as FDD(Ex.
Multi-Touch Panel PC AEC-5185 Super IO Configuration Chapter 3 AMI BIOS Setup 3-17
Multi-Touch Panel PC AEC-5185 Serial Port 1 Configuration Options summary: Serial Port Disabled Enabled Default Allows BIOS to En/Disable correspond serial port. Change Settings Auto Default IO=3F8h; IRQ=4; IO=3F8h; IRQ=3,4,5,6,7,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,10,11,12; Allows BIOS to select serial port resource. Device Mode Standard Serial Port Mode Default IrDA 1.0 (HP SIR) Mode ASKIR Mode Change the serial port mode.
Multi-Touch Panel PC AEC-5185 H/W Monitor Chapter 3 AMI BIOS Setup 3-19
Multi-Touch Panel PC AEC-5185 AMT Configuration Options summary: AMT Disabled Enabled Intel AMT Enable/Disable Unconfigure AMT/ME Optimal Default, Failsafe Default Disabled Optimal Default, Failsafe Default Enabled Perform AMT/ME unconfigure without password operation WatchDog Timer Disabled Optimal Default, Failsafe Default Enabled Enable/Disable WatchDog Timer OS WatchDog Timer 0~255 (0) Optimal Default, Failsafe Default Set OS WatchDog Timer BIOS WatchDog Timer 0~255 (0) Optimal Default, Failsafe
Multi-Touch Panel PC AEC-5185 CompactFlash Controller Configuration Options summary: ATA Controller Disabled IDE Mode Select an operative mode for ATA controller Optimal Default, Failsafe Default Chapter 3 AMI BIOS Setup 3-21
Multi-Touch Panel PC AEC-5185 Serial Port Condole Redirection Options summary: Console Redirection Disabled Enabled Console Redirection Enable/Disable Chapter 3 AMI BIOS Setup 3-22 Optimal Default, Failsafe Default
Multi-Touch Panel PC AEC-5185 Setup submenu: Chipset Chapter 3 AMI BIOS Setup 3-23
Multi-Touch Panel PC North Bridge Chapter 3 AMI BIOS Setup 3-24 AEC-5185
Multi-Touch Panel PC AEC-5185 Options summary: Low MMIO Align 64M Optimal Default, Failsafe Default 1024M Low MMIO resource align at 64MB/1024MB Initiate Graphic Adapter IGD PCI/IGD PCI/PEG PEG/IGD Optimal Default, Failsafe Default PEG/PCI Select which graphics controller to use as the primary boot device Graphics Turbo IMON 14~31(31) Optimal Default, Failsafe Default Current Graphics turbo IMON current values supported VT-d Disabled Optimal Default, Failsafe Default Enabled Check to enable VT-d function
Multi-Touch Panel PC South Bridge Chapter 3 AMI BIOS Setup 3-26 AEC-5185
Multi-Touch Panel PC AEC-5185 Options summary: 82577 SMBus Controller Disabled Enabled Optimal Default, Failsafe Default 82577 SMBus Controller Enable/Disable 82577 GbE Controller Disabled Enabled Optimal Default, Failsafe Default 82577 GbE Controller Enable/Disable 82577 Wake on LAN from S5 Disabled Enabled Optimal Default, Failsafe Default 82577 Wake on LAN from S5 Enable/Disable Restore AC Power Loss Power Off Optimal Default, Failsafe Default Power On Last State Select AC power state when power is re
Multi-Touch Panel PC AEC-5185 ME Subsystem Options summary: ME Subsystem Disabled Enabled ME Subsystem Enable/Disable End of Post Message Disabled Enabled End of Post Message Enable/Disable Execute MEBx Disabled Enabled Execute MEBx Enable/Disable Chapter 3 AMI BIOS Setup 3-28 Optimal Default, Failsafe Default Optimal Default, Failsafe Default Optimal Default, Failsafe Default
Multi-Touch Panel PC AEC-5185 Setup submenu: Boot Chapter 3 AMI BIOS Setup 3-29
Multi-Touch Panel PC AEC-5185 Options summary: Quiet Boot Disabled Optimal Default, Failsafe Default Enabled En/Disable showing boot logo. Setup Prompt Timeout 1~65535 (1) Optimal Default, Failsafe Default Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting.
Multi-Touch Panel PC AEC-5185 BBS Priorities Chapter 3 AMI BIOS Setup 3-31
Multi-Touch Panel PC AEC-5185 Security Change User/Supervisor Password You can install a Supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the Setup utility. If you highlight these items and press Enter, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers. Press Enter after you have typed in the password.
Multi-Touch Panel PC AEC-5185 Setup submenu: Exit Chapter 3 AMI BIOS Setup 3-33
Multi-Touch Panel PC ACP-5185 Chapter 4 Driver Installation Chapter 4 Driver Installation 4-1
Multi-Touch Panel PC ACP-5185 The ACP-5185 comes with an AutoRun DVD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver DVD, the driver DVD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers.
Multi-Touch Panel PC 4.1 ACP-5185 Installation: Insert the ACP-5185 DVD-ROM into the DVD-ROM drive. Then install the drivers from Step 1 to Step 9 in order. Step 1 – Install Chipset Driver 1. Click on the Step1–CHIPSET folder and double click on the infinst_autol(9.1.1.1020).exe file 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 2 – Install VGA Driver 1. Click on the Step2–VGA folder and select the OS folder your system is 2.
Multi-Touch Panel PC ACP-5185 Step 4 –Install ME Driver 1. Click on the Step4–ME folder and double click on the Setup.exe file 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 5 – Install Audio Driver 1. Click on the Step5–AUDIO folder double click on the SETUP.exe file 2. Follow the instructions that the window shows 3.
Multi-Touch Panel PC ACP-5185 Step 8 – Install WiFi & Bluetooth Driver (Optional) 1. Click on the Step8–WIFI&BLUETOOTH folder and select the OS folder your system is 2. Double click on the .exe located in each OS folder 3. Follow the instructions that the window shows 4.
Multi-Touch Panel PC ACP-5185 Step 2: The setting procedures “ In BIOS Setup Menu” A: Advanced -> SATA Configuration -> SATA Mode -> RAID Mode Step 3: The setting procedures “In BIOS Setup Menu” B: Advanced -> Launch Storage OpROM -> Enabled Chapter 4 Driver Installation 4-6
Multi-Touch Panel PC ACP-5185 Step 4: The setting procedures “In BIOS Setup Menu” C: Boot -> Boot Option #1 -> DVD-ROM Type Step 5: The setting procedures “In BIOS Setup Menu” D: Save & Exit -> Save Changes and Exit Chapter 4 Driver Installation 4-7
Multi-Touch Panel PC Step 6: Press Ctrl-I to enter MAIN MENU Step 7: Choose “1.
Multi-Touch Panel PC ACP-5185 Step 8: RAID Level -> RAID0(Stripe) Step 9: Choose “Create Volume” Chapter 4 Driver Installation 4-9
Multi-Touch Panel PC Step 10: Choose “Y” Step 11: Choose “5.
Multi-Touch Panel PC ACP-5185 Step 12: Choose “Y” Step 13: Setup OS Chapter 4 Driver Installation 4-11
Multi-Touch Panel PC Step 14: Press “F6” Step 15: Choose “S” Chapter 4 Driver Installation 4-12 ACP-5185
Multi-Touch Panel PC ACP-5185 Step 16: Choose “Intel(R) Mobile Express Chipset SATA RAID Controller” Step 17: It will show the model number you select and then press “ENTER” Chapter 4 Driver Installation 4-13
Multi-Touch Panel PC ACP-5185 Step 18: Setup is starting Windows Setting AHCI OS installation to setup AHCI Mode Step 1: Copy the files below from “Driver CD -> Step7- RAID & AHCI” to Disk Chapter 4 Driver Installation 4-14
Multi-Touch Panel PC ACP-5185 Step 2: The setting procedures “ In BIOS Setup Menu” A: Advanced -> SATA Configuration -> SATA Configuration -> SATA Mode -> AHCI Mode Step 3: The setting procedures “In BIOS Setup Menu” B: Boot -> Boot Option #1 -> DVD-ROM Type Chapter 4 Driver Installation 4-15
Multi-Touch Panel PC ACP-5185 Step 4: The setting procedures “In BIOS Setup Menu” C: Save & Exit -> Save Changes and Exit Step 5: Setup OS Chapter 4 Driver Installation 4-16
Multi-Touch Panel PC ACP-5185 Step 6: Press “F6” Step 7: Choose “S” Chapter 4 Driver Installation 4-17
Multi-Touch Panel PC ACP-5185 Step 8: Choose “Intel(R) 7 Series Chipset Family SATA AHCI Controller” Step 9: It will show the model number you select and then press “ENTER” Chapter 4 Driver Installation 4-18
Multi-Touch Panel PC ACP-5185 Step 10: Setup is loading files Chapter 4 Driver Installation 4-19
Multi-Touch Panel PC ACP-5185 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Multi-Touch Panel PC ACP-5185 A.1 Programming ACP-5185 utilizes ITE 8781 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON initial watchdog timer program is also attached based on which you can develop customized programs to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8781 enters the normal mode with all logical devices disabled except KBC.
Multi-Touch Panel PC ACP-5185 There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
Multi-Touch Panel PC ACP-5185 WatchDog Timer Configuration Registers Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
Multi-Touch Panel PC ACP-5185 Watch Dog Timer 1, 2, 3 Configuration Register (Index=72h, 82h, 92h Default=001s0000b) Watch Dog Timer 1,2,3 Time-Out Value (LSB) Register (Index=73h,83h,93h, Default=38h) Watch Dog Timer 1,2,3 Time-Out Value (MSB) Register (Index=74h,84h,94h Default=00h) Appendix A Programming the Watchdog Timer A-5
Multi-Touch Panel PC ACP-5185 A.2 ITE8781 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
Multi-Touch Panel PC ACP-5185 ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h CALL Write_Configuration_Data Appendix A Programming the Watchdog Timer A-7
Multi-Touch Panel PC RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,81h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL Appendix A Programming the Watchdog Timer A-8 ACP-5185
Multi-Touch Panel PC ACP-5185 MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
Multi-Touch Panel PC ACP-5185 push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
Multi-Touch Panel PC ACP-5185 Appendix B I/O Information Appendix B I/O Information B-1
Multi-Touch Panel PC B.
Multi-Touch Panel PC ACP-5185 Appendix B I/O Information B - 3
Multi-Touch Panel PC B.
Multi-Touch Panel PC ACP-5185 B.3 IRQ Mapping Chart B.
Multi-Touch Panel PC ACP-5185 Appendix C Miscellanea Appendix C Miscellanea C-1
Multi-Touch Panel PC ACP-5185 C.1 General Cleaning Tips You may need the following precautions before you begin to clean the computer. When you clean any single part or component for the computer, please read and understand the details below fully. 1. Never spray or squirt the liquids directly onto any computer component. If you need to clean the device, please rub it with a piece of dry cloth. 2. Be cautious of the tiny removable components when you use a vacuum cleaner to absorb the dirt on the floor.
Multi-Touch Panel PC ACP-5185 C.2 Cleaning tools Although many companies have created products to help improve the process of cleaning your computer and peripherals users can also use household items to clean their computers and peripherals. Below is a listing of items you may need or want to use while cleaning your computer or computer peripherals.
Multi-Touch Panel PC ACP-5185 Cotton swabs - Cotton swaps moistened with rubbing alcohol or water are excellent tools for wiping hard to reach areas in your keyboard, mouse, and other locations. Foam swabs - Whenever possible it is better to use lint free swabs such as foam swabs. Note: We strongly recommended that you should shut down the system before you start to clean any single components. Please follow the steps below. 1. Close all application programs 2. Close operating software 3.
Multi-Touch Panel PC ACP-5185 C.3 Scrap Computer Recycling If the computer equipments need the maintenance or are beyond repair, we strongly recommended that you should inform us as soon as possible for the suitable solution. For the computers that are no longer useful or work well, please contact with worldwide distributors for recycling. The worldwide distributors show on the following website: http://www.aaeon.
Multi-Touch Panel PC ACP-5185 C.
Multi-Touch Panel PC ACP-5185 MSR Installation Step 1: Fasten the two screws (2-SELF TAPPING SCREWS) to fix the MSR Bracket with the ACP-5185 Appendix C Miscellanea C-7
Multi-Touch Panel PC ACP-5185 Bar Code Scanner Installation Step 1: Fasten the three screws to fix the Bar Code Scanner with the backet Appendix C Miscellanea C-8
Multi-Touch Panel PC ACP-5185 Step 2: Fasten the two screws (2-SELF TAPPING SCREWS) to fix the Bar Code Scanner with the ACP-5185 Appendix C Miscellanea C-9
