Wallmount Chassis AEC-206 AEC-206 Wallmount Chassis AEC-206 Manual Rev.A 2nd Ed. Part No. 2007206012 Printed in Taiwan, Oct.
Wallmount Chassis AEC-206 Copyright Notice This document is copyrighted, 2007. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Wallmount Chassis AEC-206 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specification .............................................................. 1-4 1.4 Dimension Diagram................................................... 1-6 1.5 Connector and Drive Bay Location Diagram............. 1-7 Chapter 2 Quick Installation Guide 2.
Wallmount Chassis AEC-206 Chapter 1 General Information Chapter 1 General Information 1-1
Wallmount Chassis AEC-206 1.1 Introduction The AEC-206 is 6-slot industrial wall-mount chassis ideal for wall-mount and space-constrained applications. Especially in rugged factory floor environment, AEC-206 ensures stable operation to free you from shut down risk or any other disturbance. The AEC-206 comes with a 6-slots PICMG or an ISA backplane to maximize the high performance of Pentium 4 full-size CPU Card. An ATX 12V power supply up to 300W is also equipped dedicated to Pentium 4 CPU Card.
Wallmount Chassis AEC-206 1.2 Features Supports high performance Full-Size CPU Cards Supports 6-slot PICMG bus passive backplanes Supports wallmount or desktop applications Supports one front access 5.25” CD-ROM, one 3.5” FDD and two 3.
Wallmount Chassis AEC-206 1.3 Specification System Construction: Heavy-duty steel chassis Disk drive bay: External - one 3.5” FDD or 5.25” CD-ROM; Internal - two 3.5” HDD System cooling fan: one 12 x 12 cm ball bearing fan with filter (Flow-in) Controls: Power ON/OFF switch, reset switch Indicator: HDD LED, Power ON LED I/O Port: One LVDS, one COM port, one parallel port, two USB on front panel Power supply: 1U ATX, ATX12V and AT power Dimensions (W x H x D): 9.05” x 8.51” x 15.
Wallmount Chassis AEC-206 Power Supply Options Specification Model Number W att T ype LxW xH(mm) Input Output 1757215001 150W AT 180x100x40.5 115/230V 5/12/-5/-12 1757215002 150W ATX 180x100x40.5 115/230V 3.3/5/12/-5/-12/5Vsb 1757220001 200W ATX12V 200x100x40.5 115/230V 3.3/5/12/-5/-12/5Vsb 1757215004 300W ATX12V 200x100x40.5 115/230V 3.
Wallmount Chassis 1.
Wallmount Chassis AEC-206 1.5 Connectors and Drive Bay Location Diagram 1. Two internal 3.5” hard disk bay 2. 5.25” CD-ROM drive 3. Floppy drive 4. Two USB ports 5. Power ON/OFF Switch and LED, HDD LED, Reset Switch. 6. 12cm cooling fan with filter(flow-in) 7.
Wallmount Chassis 8. COM port 9. Parallel port 10. LVDS Interface 11. Hot-Air outlet 12.
Wallmount Chassis AEC-206 Chapter 2 Quick Installation Guide Chapter 2 Quick Installation Guide 2-1
Wallmount Chassis AEC-206 2.1 Removing the cover Before you install any drives or plug-in cards into AEC-206, you have to open the cover and remove the hold-down bar first. Unscrew the cover, lift the lid and keep the top of the chassis open. Unscrew the hold-down bar and remove it.
Wallmount Chassis AEC-206 2.2 Adding a Floppy Drive To install a floppy drive, please refer to the following charts and procedures. Unscrew the mounting bracket from the chassis. Remove the black front bracket and insert the FDD into the mounting bracket with its base facing inward. Connect a 34-pin flat cable and power cable to the FDD, and attach the FDD to the bracket with four screws. Attach the mounting bracket with the FDD inside to the chassis with four screws.
Wallmount Chassis AEC-206 2.3 Adding a CD-ROM Drive To install a CD-ROM drive, please refer to the following charts and procedures. Unscrew the mounting bracket from the chassis. Unscrew the black front bracket and insert the CD-ROM drive into the mounting bracket with its base facing inward. Connect a 40-pin flat cable and power cable to the CD-ROM drive, and attach it to the bracket with four screws. Attach the mounting bracket with the CD-ROM drive inside to the chassis with four screws.
Wallmount Chassis AEC-206 2.4 Adding a Hard Disk Drive To install a hard disk drive, please refer to the following charts and procedures. Unscrew the mounting bracket from the chassis. Insert the hard disk drive to the mounting bracket and get it screwed in the four holes on the side of the hard disk. Attach the mounting bracket with the hard disk drive inside to the chassis with four screws.
Wallmount Chassis AEC-206 2.5 Adding the hold-down bar After you assemble all the drives, plug-in cards and cables inside the chassis, be sure to put the hold-down bar back to strength its anti-vibration ability. Screw the hold-down bar to the same location from where it was removed in the first step. Then close the cover of the chassis and get it screwed.
Wallmount Chassis AEC-206 2.6 Replacing the filter You may need to replace the used filter after a period of time. Please refer to the following charts and procedures. Remove the two screws located at the bottom of the filter cover then pull the cover free from the chassis Remove the filter and replace it with a new one. Insert the filter and the cover back to the chassis and screw the cover through the hole at the bottom.
Wallmount Chassis AEC-206 2.7 Adding the wallmount kit You can easily mount AEC-206 onto wall with the supplied wallmount kit. Turn over the chassis to expose its bottom upward. Fasten the two brackets with six screws.
Wallmount Chassis AEC-206 Appendix A Front Panel Daughterboard and backplane Appendix A Front Panel Daughterboard and Backplane A-1
Wallmount Chassis AEC-206 A.1 Front Panel Daughterboard Mechanical Drawing A.2 Front Panel Daughterboard Jumpers & Connectors The board has a number of jumper and connectors that allow you to configure your system to suit your application.
Wallmount Chassis AEC-206 Power Connector(CN1) This power connector is used for AT mode with ATX power supply.
Wallmount Chassis AEC-206 BP206SI-V60 Unit: mm BP206SG-P3-V61 Unit: mm Appendix A Front Panel Daughterboard and Backplane A-4
