Embedded Controller AEC-6872 AEC-6872 Fanless Embedded Controller Intel® AtomTM D510 Processor with 2 Gigabit Ethernet 10 COMs, Audio, 4 USB 1 PCI-E or 1 PCI AEC-6872 Manual 1st Ed.
Embedded Controller AEC-6872 Copyright Notice This document is copyrighted, 2011. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Embedded Controller AEC-6872 Acknowledgments • Award is a trademark of Award Software International, Inc. • CompactFlash™ is a trademark of the Compact Flash Association. • Intel®, and Atom™ are trademarkes of Intel® Corporation. • Microsoft Windows is a registered trademark of Microsoft Corp. • PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation. ® All other product names or trademarks are properties of their respective owners.
Embedded Controller AEC-6872 Packing List Before you begin operating your PC, please make sure that the following materials have been shipped: z 1 AEC-6872 Embedded Controller z 1 Phoenix Power Connector z 2 Wallmount Brackets z 1 CD-ROM for manual (in PDF format) and drivers If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Embedded Controller AEC-6872 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a firm surface during installation.
Embedded Controller AEC-6872 d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°C (-4°F) OR ABOVE 60°C (140°F). IT MAY DAMAGE THE EQUIPMENT. FCC This device complies with Part 15 FCC Rules.
Embedded Controller AEC-6872 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Boxer/ Industrial System 有毒有害物质或元素 部件名称 铅 汞 (Pb) (Hg) 印刷电路板 镉 六价铬 多溴联苯 多溴二苯 (Cd) (Cr(VI)) (PBB) 醚(PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期限，系指在一般正常使用状况下。 二、上述部件物
Embedded Controller AEC-6872 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-4 1.3 Specifications ............................................................ 1-5 Chapter 2 Hardware Installation 2.1 Dimension ................................................................. 2-2 2.2 COM2 Ring/+5V/+12V Selection (JP3) ..................... 2-3 2.
Embedded Controller AEC-6872 Appendix B I/O Information B.1 I/O Address Map ..................................................B-2 B.2 Memory Address Map ..........................................B-4 B.3 IRQ Mapping Chart ..............................................B-5 B.4 DMA Channel Assignments .................................
Embedded Controller AEC-6872 Chapter 1 General Information Chapter 1 General Information 1- 1
Embedded Controller AEC-6872 1.1 Introduction Due to the growing popularity from the IPC market, the newest Boxer series AEC-6872 has been introduced by AAEON. New Innovation for Entertainment Multimedia Domain In this era of information explosion, the advertising of consumer products will not be confined to the family television, but will also spread to high-traffic public areas, like department stores, the bus, transportation station, the supermarket etc.
Embedded Controller AEC-6872 5 g rms. With the anti-vibration hard drive device option, the AEC-6872 can be used in high vibration environments. In addition, the AEC-6872 offers low power consumption system that while operating in ambient temperatures ranging from -10° to 55°C. The AEC-6872 is a standalone high performance controller designed for long-life operation and with high reliability. It can replace traditional methods and become the mainstream controller for the multimedia entertainment market.
Embedded Controller AEC-6872 1.
Embedded Controller AEC-6872 1.3 Specifications z CPU Intel® AtomTM D510 1.6 GHz Processor z Chipset Intel® ICH8M z System Memory 200-pin DDR2 SODIMM x 2, Max. 4GB z Display DB-15 x 1, shared system memory up VGA Interface z Storage to 384MB/DVMT 4.0 SSD Device Type 2 CompactFlash™ Slot x 1 (inside) HDD SATA 1.5 Gb/s HDD bay x 1 z Network LAN Gigabit Ethernet z Front I/O Serial Port RS-232 x 8 Others LPT x 1 USB Host USB2.
Embedded Controller AEC-6872 z Power Requirement DC 9-30V z System Cooling Passive cooling z Mounting Wallmount z Operating Temperature Ambient with Airflow 14oF ~ 131oF (-10oC ~ 55oC) (w/ WT CFD); 14oF ~ 122oF (-10oC ~ 50oC) (w/ D510, WT HDD) z Storage Temperature -4oF ~ 158oF (-20oC ~ 70oC) z Anti-Vibration 5 g rms/ 5~500 Hz/ operation-CFD; 1 g rms/ 5~500 Hz/ operation-HDD z Anti-Shock 50 G peak acceleration (11 msec.
Embedded Controller AEC-6872 Chapter 1 General Information 1- 7
Embedded Controller AEC-6872 Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
Embedded Controller 2.
Embedded Controller AEC-6872 2.2 COM2 Ring/+5V/+12V Selection (JP3) JP3 Function 1-2 +12V 3-4 Ring (Default) 5-6 +5V 2.3 Clear CMOS (JP5) JP5 Function 1-2 Protected (Default) 2-3 Clear 2.
Embedded Controller AEC-6872 Step 2: Unfasten the six screws to release the brackets and bottom lid of AEC-6872 Step 3: Cover with a thermal pad Chapter 2 Hardware Installation 2 - 4
Embedded Controller AEC-6872 Step 4: Insert the RAM module to the AEC-6872 Step 5: Fasten the six screws to lock the brackets and bottom lid of AEC-6872 Chapter 2 Hardware Installation 2 - 5
Embedded Controller AEC-6872 Step 6: Fasten the two screws on the front and rear panels of AEC-6872 Chapter 2 Hardware Installation 2 - 6
Embedded Controller AEC-6872 2.
Embedded Controller AEC-6872 Step 3: Fasten the four HDD screws and cover with the four black damper Chapter 2 Hardware Installation 2 - 8
Embedded Controller AEC-6872 Step 4: Place the HDD to the HDD bracket Step 5: Assembly the damper bracket and fasten the four screws Chapter 2 Hardware Installation 2 - 9
Embedded Controller AEC-6872 Step 6: Connect the SATA and power cables HDD DISK SATA Power W/LOCK Chapter 2 Hardware Installation 2 - 10 I/O Board Side
Embedded Controller AEC-6872 Step 7: Fasten the two screws on the front and rear panels of AEC-6872 Step 8: Fasten the six screws to release the brackets and bottom lid of AEC-6872 Chapter 2 Hardware Installation 2 - 11
Embedded Controller AEC-6872 2.
Embedded Controller AEC-6872 Step 3: Remove the screw with your finger and get the PCI-Express card ready to install. You should keep the shield and screw for use later.
Embedded Controller AEC-6872 Step 5: Insert the PCI-Express card into the PCI-Express slot and reattach the screw. Fasten the screw and push the tenon to lock the PCI-Express card in position.
Embedded Controller AEC-6872 Step 7: Fasten the six screws on the bottom lid Step 8: Fasten the two screws on the front and rear panels Chapter 2 Hardware Installation 2 - 15
Embedded Controller AEC-6872 2.
Embedded Controller AEC-6872 Step 3: Remove the screw with your finger and get the PCI card ready to install. You should keep the shield and screw for use later. Step 4: Insert the PCI card into the PCI slot and reattach the screw. Push the tenon to lock the PCI-Express card in position.
Embedded Controller AEC-6872 Step 5: Make sure the balance of PCI card while installing Step 6: Fasten the six screws on the bottom lid Chapter 2 Hardware Installation 2 - 18
Embedded Controller AEC-6872 Step 7: Fasten the two screws on the front and rear panels Chapter 2 Hardware Installation 2 - 19
Embedded Controller AEC-6872 2.8 Wallmount Bracket Installation Fasten the brackets with the appropriate screws.
Embedded Controller AEC-6872 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Embedded Controller 3.1 AEC-6872 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration against the values stored in the CMOS memory.
Embedded Controller 3.2 AEC-6872 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Embedded Controller AEC-6872 Chapter 4 Driver Installation Chapter 4 Driver Installation 4 - 1
Embedded Controller AEC-6872 The AEC-6872 comes with a CD-ROM that contains all drivers and utilities that meet your needs. Follow the sequence below to install the drivers: Step 1 – Install Chipset Driver Step 2 – Install VGA Driver Step 3 – Install Audio Driver Step 4 – Install LAN Driver Please read instructions below for further detailed installations.
Embedded Controller AEC-6872 4.1 Installation Insert the AEC-6872 CD-ROM into the CD-ROM Drive. And install the drivers from Step 1 to Step 4 in order. Step 1 – Install Chipset Driver 1. Click on the Step 1 - Chipset folder and then double click on the infinst_autol.exe 2. Follow the instructions that the window will show you 3. The system will help you install the driver automatically Step 2 – Install VGA Driver 1.
Embedded Controller AEC-6872 Step 4 – Install LAN Driver 1. Click on the Step 4 - LAN folder and select the OS your system is 2. Double click on the setup.exe file located in each OS folder 3. Follow the instructions that the window shows you 4.
Embedded Controller AEC-6872 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Embedded Controller AEC-6872 A.1 Programming AEC-6872 utilizes W83627UHG chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application.
Embedded Controller AEC-6872 (3) Exit the W83627UHG config Mode. Undesired result may occur if the config Mode is not exited normally. (1) Enter the W83627UHG config Mode To enter the W83627UHG config Mode, two special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform two write operations to the Special Address port (2EH).
Embedded Controller AEC-6872 1 R/W 0: GPIO5 is inactive. 1: GPIO5 is active. 0 R/W 0: WDTO# and PLED are inactive. 1: WDTO# and PLED are inactive. CR F5h. (WDTO# and KBC P20 Control Mode Register; Default 00h) BIT READ/WRITE 7~5 Reserved. 4 R/W 3 R/W 2 R/W 1 R/W 0 DESCRIPTION 1000 time faster in WDTO# count mode. 0: Disable. 1: Enable. (If bit-3 is Second Mode, the count mode is 1/1000 Sec.) (If bit-3 is Minute Mode, the count mode is 1/1000 Min.) Select WDTO# count mode.
Embedded Controller AEC-6872 01h: Time-out occurs after 1 second/minute 02h: Time-out occurs after 2 second/minutes 03h: Time-out occurs after 3 second/minutes ………………………………………………….. FFh: Time-out occurs after 255 second/minutes CR F7h. (WDTO# Control & Status Register; Default 00h) BIT READ/WRITE 7 R/W 6 R/W 5 Write “1” Only 4 R/W Write“0”Clear 3~0 R/W DESCRIPTION Mouse interrupt reset watch-dog timer enable 0: Watchdog timer is not affected by mouse interrupt.
Embedded Controller AEC-6872 A.2 W83627UHG Watchdog Timer Initial Program Example: Setting 10 sec. as Watchdog timeout interval #include #include
Embedded Controller AEC-6872 // Set WatchDog time is 10 sec outportb(EFER_Port,0xf6); outportb(EFER_Port+1,0x0A); time is 10 sec outportb(EFER_Port,0xAA); exit } Appendix A Programming the Watchdog Timer A-7
Embedded Controller AEC-6872 Appendix B I/O Information Appendix B I/O Information B-1
Embedded Controller B.
Embedded Controller AEC-6872 Appendix B I/O Information B-3
Embedded Controller B.
Embedded Controller AEC-6872 B.3 IRQ Mapping Chart B.
