N e t w o r k Ap p l i a n c e FWS-2200 FWS-2200 Desktop Network Appliance Platform 2.5” SATA HDD, CF SATA Socket 6 LAN Ports 2 USB2.0, 1 COM for Console 1 Mini PCI th FWS-2200 Manual 4 Ed.
N e t w o r k Ap p l i a n c e FWS-2200 Copyright Notice This document is copyrighted, 2014. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
N e t w o r k Ap p l i a n c e FWS-2200 Acknowledgments All other products’ name or trademarks are properties of their respective owners. ® ® Intel and Atom™ are trademarks of Intel Corporation. AMI is a trademark of American Megatrends Inc. CompactFlash™ is a trademark of the Compact Flash Association. Microsoft Windows is a registered trademark of Microsoft Corp. ® All other product names or trademarks are properties of their respective owners.
N e t w o r k Ap p l i a n c e FWS-2200 Caution There is a danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions and your local government’s recycling or disposal directives. Attention: Il y a un risque d’explosion si la batterie est remplacée de façon incorrecte. Ne la remplacer qu’avec le même modèle ou équivalent recommandé par le constructeur.
N e t w o r k Ap p l i a n c e FWS-2200 Packing List Before you begin installing your card, please make sure that the following materials have been shipped: FWS-2200 CD-ROM for manual (in PDF format) and drivers D-sub 9-pin Cable x 1 Rubber Foots 60W Power Adapter SATA Power Cable x 1 SATA Cable x 1 If any of these items should be missing or damaged, please contact your distributor or sales representative immediately. Note: VGA Cable is an optional accessory.
N e t w o r k Ap p l i a n c e FWS-2200 Contents Chapter 1 General Information 1.1 Introduction .......................................................... 1-2 1.2 Features .............................................................. 1-3 1.3 Specifications ...................................................... 1-4 1.4 General System Information ............................... 1-7 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .............................................. 2-2 2.
N e t w o r k Ap p l i a n c e FWS-2200 2.17 Installing the Hard Disk Drive ............................ 2-12 Chapter 3 AMI BIOS Setup 3.1 System Test and Initialization ............................. 3-2 3.2 AMI BIOS Setup .................................................. 3-3 Chapter 4 Driver Installation 4.1 Installation ........................................................... 4-3 Appendix A Programming the Watchdog Timer A.1 Programming .................................................. A-2 A.
N e t w o r k Ap p l i a n c e FWS-2200 Chapter 1 General Information Chapter 1 General Information 1- 1
N e t w o r k Ap p l i a n c e FWS-2200 1.1 Introduction FWS-2200 adopts the Intel® Dual Core Atom™ D525 Processor and equips with Intel® Atom™ D525 + ICH8M chipset. The system memory features two 204-pin single channel DDR3 800MHz SODIMM slots up to 4GB. It deploys six Gigabit Ethernet LAN ports with one pair LAN bypass function (two pairs bypass function is optional). FWS-2200 condensed appearance features desktop form factor that fits nicely into a space-limited environment.
N e t w o r k Ap p l i a n c e FWS-2200 1.2 Features Desktop platform 6 LAN ports Network Appliance Onboard Intel® Dual-Core Atom™ D525 processor Intel® Atom™D525 + ICH8M Two 204-pin Single Channel DDR3 800MHz SODIMM Up to 4GB 10/100/1000Base-TX Ethernet Port x 6 With One Pair LAN Bypass Function (Two Pairs Bypass Function Is Optional) 2.5” SATA HDD x 1 and CF-SATA socket COM for Console x 1, USB2.
N e t w o r k Ap p l i a n c e FWS-2200 1.3 Specifications System Form Factor Desktop 6 LAN ports Network Appliance Processor Onboard Intel® Atom™ D525 processor System Memory 204-pin single channel DDR3 800MHz SODIMM slot x 2, up to 4GB Chipset Intel® Atom™ D525 + ICH8M Ethernet Intel® 82574L controller, Gigabit Ethernet x 6 with 1 pair LAN bypass function (two pairs LAN bypass function is optional) BIOS AMI BIOS Serial ATA SATA 3.
N e t w o r k Ap p l i a n c e FWS-2200 connector x 1, DC power input x 1, Software programmable button x 1 Color Black Power Supply 60W AC/DC power adapter Dimension 10.24”(W) x 7.01”(D) x 1.
N e t w o r k Ap p l i a n c e FWS-2200 Temperature Storage -4oF~104oF (-20oC ~60oC) Temperature Operating Humidity 10%~80% relative humidity, non-condensing Storage Humidity 10%~80% @ 40oC, non-condensing Vibration 0.5g rms/5~500Hz/ operation (2.5” HDD) 1.5g rms/5~500Hz/ non-operation Shock 10G peak acceleration (11m sec. duration), operation 20G peak acceleration (11m sec.
N e t w o r k Ap p l i a n c e FWS-2200 1.
Ne tw ork Ap p lia nce FWS-2200 Chapter 2 Quick Installation Guide Chapter 2 Quick Installation Guide 2-1
Ne tw ork Ap p lia nce FWS-2200 2.1 Safety Precautions The installation is intended for technically qualified personnel who have experience installing and configuring system boards. The equipment can be installed in a restricted access location (RAL) only. A restricted access location is a site location for equipment where the following criteria apply: 01. Access can only be gained by service persons or by users who have been trained on the restrictions and the precautions for this specific site. 02.
Ne tw ork Ap p lia nce FWS-2200 2.
Ne tw ork Ap p lia nce 2.
Ne tw ork Ap p lia nce FWS-2200 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: Label Function JP3 CMOS Setting Selection JP6 Auto PWRBTN Selection 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Ne tw ork Ap p lia nce FWS-2200 MPCI1 Mini PCI Slot SATA1 SATA INTERFACE CN2 SATA POWER SYSFAN1 4-PIN Fan Connector SYSFAN2 4-PIN Fan Connector CPUFAN1 4-PIN Fan Connector GPIO1 Digital I/O CFD1 CF-SATA CARD SOCKET LLED1 LAN LED Pin Header BPLED1 Bypass LED Pin Header PSW1 Power On/Off Switch RSW1 Software Programmable Button Chapter 2 Quick Installation Guide 2-6
Ne tw ork Ap p lia nce FWS-2200 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Ne tw ork Ap p lia nce FWS-2200 2.7 CMOS Setting Selection (JP3) JP3 Function 1-2 Normal (Default) 2-3 Clear CMOS 2.8 Auto PWRBTN Selection (JP6) JP6 Function 1-2 Don’t use Auto PWRBTN (Default) 2-3 Use Auto PWRBTN 2.9 4-pin ATX Power Connector (CN9) Pin Signal Pin Signal 1 GND 2 GND 3 +12V 4 +12V 2.
Ne tw ork Ap p lia nce FWS-2200 2.11 Pin Header (USB2) Pin Signal Pin Signal 1 +5V 2 GND 3 USBD1- 4 GND 5 USBD1+ 6 USBD2+ 7 GND 8 USBD2- 9 GND 10 +5V 11 CD-L 2.12 RS-232 Box Header (COM2) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N.C 2.
Ne tw ork Ap p lia nce FWS-2200 2.
Ne tw ork Ap p lia nce FWS-2200 22 PDD1 47 PDD8 23 PDD2 48 PDD9 24 NC 49 PDD10 25 GND 50 GND 2.15 Software Programmable Button (RSW1) Pin Signal Pin Signal 1 SOFTWAREPRGM- 2 GND Button status: I/O Space 0x4BA bit 0 2.
Ne tw ork Ap p lia nce FWS-2200 2.
Ne tw ork Ap p lia nce FWS-2200 Step3: Turn the screw to open the HDD case Step4: Fasten the four screws of the Hard DISK Drive Bracket Chapter 2 Quick Installation Guide 2-13
Ne tw ork Ap p lia nce FWS-2200 Step5: Plug the SATA cable & Power cable in the HDD Step6: Put the HDD with cable onto the HDD Bracket Chapter 2 Quick Installation Guide 2-14
Ne tw ork Ap p lia nce FWS-2200 Step7: Close the upper bracket of the HDD case and make sure the rubber feet are locked by the flutes on the brackets Chapter 2 Quick Installation Guide 2-15
Ne tw ork Ap p lia nce FWS-2200 Step8: Fasten the screw conversely to lock the HDD Step9: Plug the SATA cable & Power cable in the SATA socket & Power socket on the main board Chapter 2 Quick Installation Guide 2-16
Ne tw ork Ap p lia nce FWS-2200 Step10: Insert the HDD to the chassis horizontally and lock the HDD case Chapter 2 Quick Installation Guide 2-17
Ne tw ork Ap p lia nce FWS-2200 Step11: Close and screw the upper cover of the chassis Chapter 2 Quick Installation Guide 2-18
Ne tw ork Ap p lia nce FWS-2200 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Boxer/ Industrial System 有毒有害物质或元素 部件名称 铅 汞 镉 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 六价铬 多溴联苯 多溴二苯醚 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注： 一、此产品所标示之环保使用期限，系指在一般正常使用状况下。 二
N e t w o r k Ap p l i a n c e FWS-2200 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
N e t w o r k Ap p l i a n c e FWS-2200 3.1 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
N e t w o r k Ap p l i a n c e FWS-2200 3.2 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM and BIOS NVRAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup.
N e t w o r k Ap p l i a n c e Setup Menu Main Chapter 3 AMI BIOS Setup 3-4 FWS-2200
N e t w o r k Ap p l i a n c e FWS-2200 Advanced Chapter 3 AMI BIOS Setup 3-5
N e t w o r k Ap p l i a n c e FWS-2200 ACPI Settings Options summary : Suspend mode Supend Disabled S1 (CPU Stop Clock) S3 (Suspend to RAM) S1 & S3 (Auto) Select the ACPI state used for System Suspend Chapter 3 AMI BIOS Setup 3-6 Default
N e t w o r k Ap p l i a n c e FWS-2200 CPU Configuration Options summary : Hyper-Threading Disabled Enabled Default En/Disable Intel Hyper-Threading Technology.
N e t w o r k Ap p l i a n c e FWS-2200 IDE Configuration Options summary : ATA Or IDE Disabled Configuration Compatible Enhanced Default Select ATA or IDE Configuration. Configure SATA As IDE AHCI Select SATA Controller mode.
N e t w o r k Ap p l i a n c e FWS-2200 LAN Bypass Configuration Options summary : LAN1_2 Power ON ByPass PassTru Default Select LAN1 / 2 operation mode when system is Power On. LAN1_2 Power OFF ByPass PassTru Default Select LAN1 / 2 operation mode when system is Power Off. LAN3_4 Power ON ByPass PassTru Default Select LAN3 / 4 operation mode when system is Power On.
N e t w o r k Ap p l i a n c e FWS-2200 LAN3_4 Power OFF ByPass PassTru Default Select LAN3 / 4 operation mode when system is Power Off. WDT ByPass Reset Default Select Watch Dog function as normal system reset or LAN ByPass. WDT BYPASS LAN1_2 SELECT LAN3_4 LAN1_2 AND LAN3_4 Select which pair LAN ByPass control by WDT.
N e t w o r k Ap p l i a n c e FWS-2200 Intel IGD SWSCI OpRegion Options summary : DVMT Mode Select Fixed Mode DVMT Mode Default Select DVMT Mode/Fixed Mode. DVMT/FIXED Memory 128MB 256MB Maximum Default Select DVMT/FIXED Mode Memory size used by Internal Graphics Device.
N e t w o r k Ap p l i a n c e FWS-2200 USB Configuration Options summary : Enabled Legacy USB Support Default Disabled Auto Enables BIOS Support for Legacy USB Support. When enabled, USB can be functional in legacy environment like DOS.
N e t w o r k Ap p l i a n c e FWS-2200 Super IO Configuration Chapter 3 AMI BIOS Setup 3-13
N e t w o r k Ap p l i a n c e Serial Port Configuration Chapter 3 AMI BIOS Setup 3-14 FWS-2200
N e t w o r k Ap p l i a n c e FWS-2200 Options summary : Serial Port Disabled Enabled Default Allows BIOS to En/Disable correspond serial port.
N e t w o r k Ap p l i a n c e FWS-2200 IO=2E8h; IRQ=3,4,5,6,7,10,11,12; Allows BIOS to Select Serial Port resource. Change Settings Auto (Serial Port 2) IO=2F8h; IRQ=3; IO=3F8h; IRQ=3,4,5,6,7,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,10,11,12; Allows BIOS to Select Serial Port resource.
N e t w o r k Ap p l i a n c e FWS-2200 H/W Monitor Chapter 3 AMI BIOS Setup 3-17
N e t w o r k Ap p l i a n c e FWS-2200 Smart Fan Mode Configuration Options summary : SYSFAN2 Manual Mode SYSFAN1 Thermal Cruise Mode CPUFAN1 Mode SMART FAN III Mode SYSFAN2/SYSFAN1/CPUFAN1 Mode Select SYSFAN2 91 (Default) SYSFAN1 CPUFAN1 PWM Value Input expect PWM Output Value (Range:0 - 255) Chapter 3 AMI BIOS Setup 3-18 Default
N e t w o r k Ap p l i a n c e SYSFAN2 FWS-2200 75 (Default) SYSFAN1 CPUFAN1 Target Temperature Input SYSFAN2/SYSFAN1/CPUFAN1 Target Temperature (Range:0 -127) SYSFAN2 2 (Default) SYSFAN1 CPUFAN1 Tolerance Input Tolerance of Target Temperature (Range:0 -15) SYSFAN2 255 (Default) SYSFAN1 CPUFAN1 Max Output SYSFAN2/SYSFAN1/CPUFAN1 PWM max output value (Range:0 -255) SYSFAN2 14 (Default) SYSFAN1 CPUFAN1 Output Step SYSFAN2/SYSFAN1/CPUFAN1 output step value (Range:0 -255) SYSFAN2 10 (Default) SYSFAN
N e t w o r k Ap p l i a n c e SYSFAN2 FWS-2200 10 (Default) SYSFAN1 CPUFAN1 Step up Time SYSFAN2/SYSFAN1/CPUFAN1 step up time value,unit is 0.1,default is 1 second (Range:0 -255) Serial Port Console Redirection OOptions summary : Console Redirection Disabled Enabled Console Redirection Enable or Disable.
N e t w o r k Ap p l i a n c e FWS-2200 Console Redirection Settings Options summary : Terminal Type VT100 VT100+ VT-UTF8 ANSI Default Emulation: ANSI: Extended ASCII char set. VT100: ASCII char set. VT100+: Extends VT100 to support color, functionkeys, etc. VT-UTF8: Uses UTF8 encoding to map Unicode chars onto 1 or more bytes.
N e t w o r k Ap p l i a n c e FWS-2200 38400 57600 115200 Default Selects serial port transmission speed. The speed must be matched on the other side. Long or noisy lines may require lower speeds. Dat Bits 7 8 Default Set Serial Port transmission data bits Parity None Default Even Odd Mark Space A parity bit can be sent with the data bits to detect some transmission errors. Even: Parity bit is 0 if the num of 1’s in the data bits is even.
N e t w o r k Ap p l i a n c e FWS-2200 Stop bits indicate the end of a serial data packet. (A start bit indicates the beginning). The standard setting is 1 stop bit. Communication with slow devices may require more than 1 stop bit. Flow Control None Default Hardware RTS/CTS Flow control can prevent data loss from buffer overflow. When sending data, if the receiving buffers are full, a ‘stop’ signal can be sent to stop the data flow.
N e t w o r k Ap p l i a n c e Putty Keypad VT100 FWS-2200 Default LINUX XTERMR6 SCO ESCN VT400 Select FunctionKey and KeyPad on Putty. Redirection After BIOS Always Enable POST BootLoader Default The Settings spectify if BootLoader is selected than Legacy console redirection is disabled before booting to Legacy OS. Default value is Always Enable which means Legacy Console Redirection is enabled for Legacy OS.
N e t w o r k Ap p l i a n c e FWS-2200 Chipset Chapter 3 AMI BIOS Setup 3-25
N e t w o r k Ap p l i a n c e North Bridge Chapter 3 AMI BIOS Setup 3-26 FWS-2200
N e t w o r k Ap p l i a n c e FWS-2200 OnChip VGA Configuration Options summary : Share Memory Size Disabled 1 MB 8 MB Default Select Share Memory Size.
N e t w o r k Ap p l i a n c e FWS-2200 South Bridge Options summary : ATX Power Mode Default AT Select Power supply mode: ATX: Normal ACPI support AT: Suspend/Sleep disabled, and Always On when restoring from power failure. USB Function Disabled Enabled Enable or disable USB Function.
N e t w o r k Ap p l i a n c e USB 2.0(EHCI) Support FWS-2200 Enabled Default Disabled Enable or disable USB 2.0 (EHCI) Support. Restore on Power Loss Power Off Power On Last State Default Select power state when power is re-applied after a power failure. STATUS LED CTRL LED OFF Default RED LED ON RED LED BLINK RED LED FAST BLINK GREEN LED ON GREEN LED BLINK GREEN LED FAST BLINK Select the Status LED default action.
N e t w o r k Ap p l i a n c e Resume on Ring FWS-2200 Disabled Enabled Default Enables or Disables resuming from RI# signal. Boot Options summary : Disabled Quiet Boot Enabled Default Launch I82574L PXE Disabled Default OpROM Enabled En/Disable showing boot logo.
N e t w o r k Ap p l i a n c e FWS-2200 BBS Priorities Chapter 3 AMI BIOS Setup 3-31
N e t w o r k Ap p l i a n c e FWS-2200 Security Change User/Supervisor Password You can install a Supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the Setup utility. If you highlight these items and press Enter, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers. Press Enter after you have typed in the password.
N e t w o r k Ap p l i a n c e FWS-2200 Setup utility. Removing the Password Highlight this item and type in the current password. At the next dialog box press Enter to disable password protection. Exit Save Changes and Reset Reset the system after saving the changes. This is the suggested method to exit BIOS setup menu that if you have modify any settings.
N e t w o r k Ap p l i a n c e FWS-2200 Discard Changes and Reset Reset system setup without saving any changes. It will continue system booting without reset. Restore Defaults Restore/Load Default values for all the setup options. Save as User Defaults Save the changes done so far as User Defaults. Restore User Defaults Restore the User Defaults to all the setup options.
N e t w o r k Ap p l i a n c e FWS-2200 Chapter 4 Driver Installation Chapter 4 Driver Installation 4-1
N e t w o r k Ap p l i a n c e FWS-2200 The FWS-2200 comes with an AutoRun CD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver CD, the driver CD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers.
N e t w o r k Ap p l i a n c e 4.1 FWS-2200 Installation: Insert the FWS-2200 CD-ROM into the CD-ROM drive and install the drivers from Step 1 to Step 4 in order. Step 1 – Install INF Driver 1. Click on the Step 1-Chipset folder and double click on the infinst_autol.exe 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 2 – Install VGA Driver 1. Click on the Step 2 –VGA folder and select the OS folder your system is 2.
N e t w o r k Ap p l i a n c e FWS-2200 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
N e t w o r k Ap p l i a n c e FWS-2200 A.1 Programming FWS-2200 utilizes W83627DHG chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application.
N e t w o r k Ap p l i a n c e FWS-2200 (3) Exit the W83627DHG config Mode. Undesired result may occur if the config Mode is not exited normally. (1) Enter the W83627DHG config Mode To enter the W83627DHG config Mode, two special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform two write operations to the Special Address port (2EH).
N e t w o r k Ap p l i a n c e FWS-2200 1 R/W 0: GPIO5 is inactive. 1: GPIO5 is active. 0 R/W 0: WDTO# and PLED are inactive. 1: WDTO# and PLED are inactive. CR F5h. (WDTO# and KBC P20 Control Mode Register; Default 00h) BIT READ/WRITE 7~5 Reserved. 4 R/W 3 R/W 2 R/W 1 R/W 0 DESCRIPTION 1000 time faster in WDTO# count mode. 0: Disable. 1: Enable. (If bit-3 is Second Mode, the count mode is 1/1000 Sec.) (If bit-3 is Minute Mode, the count mode is 1/1000 Min.) Select WDTO# count mode.
N e t w o r k Ap p l i a n c e FWS-2200 01h: Time-out occurs after 1 second/minute 02h: Time-out occurs after 2 second/minutes 03h: Time-out occurs after 3 second/minutes ………………………………………………….. FFh: Time-out occurs after 255 second/minutes CR F7h. (WDTO# Control & Status Register; Default 00h) BIT READ/WRITE 7 R/W 6 R/W 5 Write “1” Only 4 R/W Write“0”Clear 3~0 R/W DESCRIPTION Mouse interrupt reset watch-dog timer enable 0: Watchdog timer is not affected by mouse interrupt.
N e t w o r k Ap p l i a n c e FWS-2200 A.2 W83627DHG Watchdog Timer Initial Program LDN Register Bit WDT Timer value 0x07 0xF6 Bit [7-0] WDT Unit 0x07 0xF5 Bit3 Description 00h: Time-out Disable 01h: Time-out occurs after 1 minute only. 02h: Time-out occurs after 2 second/minutes 03h: Time-out occurs after 3 second/minutes ………………………....................................... FFh: Time-out occurs after 255 second/minutes (The deviation is approx 1 second.) Select WDTO# count mode. 0: Second Mode.
N e t w o r k Ap p l i a n c e FWS-2200 ************************************************************************************ // Procedure : AaeonWDTConfig void AaeonWDTConfig (void){ Byte val; //Super I/O Entry Key outportb(SIOIndex,0x87); outportb(SIOIndex,0x87); //Setting WDT Pin.
N e t w o r k Ap p l i a n c e FWS-2200 ************************************************************************************ // Procedure : void AaeonWDTEnable (Byte Timer, boolean Unit){ Byte val; //Super I/O Entry Key outportb(SIOIndex,0x87); outportb(SIOIndex,0x87); // Select Logic Device Number Register outportb(SIOIndex,0x07); outportb(SIOData,0x08); // Setting WDT Operation Mode outportb(SIOIndex,0xF5); val = inportb((SIOData); outportb(SIOIndex,0xF5); outportb(SIOData, val | Unit << 3 ); // Setting
N e t w o r k Ap p l i a n c e FWS-2200 Appendix B I/O Information Appendix B I/O Information B-1
N e t w o r k Ap p l i a n c e B.
N e t w o r k Ap p l i a n c e FWS-2200 Appendix B I/O Information B-3
N e t w o r k Ap p l i a n c e B.
N e t w o r k Ap p l i a n c e FWS-2200 B.
N e t w o r k Ap p l i a n c e Appendix B I/O Information B-6 FWS-2200
N e t w o r k Ap p l i a n c e FWS-2200 Appendix B I/O Information B-7
N e t w o r k Ap p l i a n c e B.
N e t w o r k Ap p l i a n c e FWS-2200 Appendix C Standard Firewall Platform Setting Appendix C Standard Firewall Platform Setting C-1
N e t w o r k Ap p l i a n c e FWS-2200 C.1 Standard Firewall Platform Setting Status LED Control Table.
N e t w o r k Ap p l i a n c e FWS-2200 ByPass Mode LAN3_4 Power On Pass Through Mode LAN3_4 Power Off ByPass Mode LAN3_4 Power Off Pass Through Mode WDT for LAN1_2 ByPass WDT for LAN3_4 ByPass WDT for system Reset Mode X X 0 1 X 1 X 1 X 0 X 1 1 X X 0 1 X X 1 0 X X 0 or 1 Note : "X" means that no affected.
N e t w o r k Ap p l i a n c e FWS-2200 C.
N e t w o r k Ap p l i a n c e FWS-2200 { UINT16 TEMP16; TEMP16 = IoIn16(LED_BASE_ADDR) & 0xF7ED; TEMP16 |= 0x0800; IoOut16(LED_BASE_ADDR, TEMP16); } // Red LED Fast Blink VOID RED_LED_FBLINK() { UINT16 TEMP16; TEMP16 = IoIn16(LED_BASE_ADDR) & 0xF7ED; TEMP16 |= 0x0802; IoOut16(LED_BASE_ADDR, TEMP16); } // Green LED On VOID GREEN_LED_ON() { UINT16 TEMP16; TEMP16 = IoIn16(LED_BASE_ADDR) & 0xF7ED; TEMP16 |= 0x0812; Appendix C Standard Firewall Platform Setting C-5
N e t w o r k Ap p l i a n c e FWS-2200 IoOut16(LED_BASE_ADDR, TEMP16); } // Green LED Blink VOID GREEN_LED_BLINK() { UINT16 TEMP16; TEMP16 = IoIn16(LED_BASE_ADDR) & 0xF7ED; TEMP16 |= 0x0012; IoOut16(LED_BASE_ADDR, TEMP16); } // Green LED Fast Blink VOID GREEN_LED_FBLINK() { UINT16 TEMP16; TEMP16 = IoIn16(LED_BASE_ADDR) & 0xF7ED; TEMP16 |= 0x0810; IoOut16(LED_BASE_ADDR, TEMP16); } Appendix C Standard Firewall Platform Setting C-6
N e t w o r k Ap p l i a n c e FWS-2200 C.
N e t w o r k Ap p l i a n c e FWS-2200 */ VOID EXE_SET() { UINT8 TEMP8; TEMP8 = IoIn8(LANBP_BASE_ADDR + 3) | 0x10; IoOut8(LANBP_BASE_ADDR + 3, TEMP8); Sleep(500); IoOut8(LANBP_BASE_ADDR + 3, TEMP8 & 0xEF); } /* LAN1 & 2 Power On ByPass Mode Set BP_MODE = 0x00 - Pass Through Mode = 0x01 - By Pass Mode */ VOID LAN12_PWRON_BP() { UINT8 TEMP8; SEL_PAIR(0x00) ; // Select Pair I TEMP8 = IoIn8(LANBP_BASE_ADDR + 1) & 0xFE; TEMP8 |= BP_MODE; Appendix C Standard Firewall Platform Setting C-8
N e t w o r k Ap p l i a n c e FWS-2200 IoOut8(LANBP_BASE_ADDR + 1, TEMP8); EXE_SET(); // Execute Set } /* LAN1 & 2 Power Off ByPass Mode Set BP_MODE = 0x00 - Pass Through Mode = 0x01 - By Pass Mode */ VOID LAN12_PWROFF_BP() { UINT8 TEMP8; SEL_PAIR(0x00) ; // Select Pair I TEMP8 = IoIn8(LANBP_BASE_ADDR) & 0x7F; TEMP8 |= BP_MODE << 7; IoOut8(LANBP_BASE_ADDR, TEMP8); EXE_SET(); // Execute Set } /* Appendix C Standard Firewall Platform Setting C-9
N e t w o r k Ap p l i a n c e FWS-2200 LAN3 & 4 Power On ByPass Mode Set BP_MODE = 0x00 - Pass Through Mode = 0x01 - By Pass Mode */ VOID LAN34_PWRON_BP() { UINT8 TEMP8; SEL_PAIR(0x01) ; // Select Pair II TEMP8 = IoIn8(LANBP_BASE_ADDR + 1) & 0xFE; TEMP8 |= BP_MODE; IoOut8(LANBP_BASE_ADDR + 1, TEMP8); EXE_SET(); // Execute Set } /* LAN3 & 4 Power Off ByPass Mode Set BP_MODE = 0x00 - Pass Through Mode = 0x01 - By Pass Mode */ VOID LAN34_PWROFF_BP() { UINT8 TEMP8; Appendix C Standard Firewall Plat
N e t w o r k Ap p l i a n c e SEL_PAIR(0x01) ; FWS-2200 // Select Pair II TEMP8 = IoIn8(LANBP_BASE_ADDR) & 0x7F; TEMP8 |= BP_MODE << 7; IoOut8(LANBP_BASE_ADDR, TEMP8); EXE_SET(); // Execute Set } /* Set Watch Dog as LAN1 & 2 By Pass mode */ VOID WDT_LAN12_BP() { UINT8 TEMP8; SEL_PAIR(0x00) ; // Select Pair I TEMP8 = IoIn8(LANBP_BASE_ADDR) | 0x40; IoOut8(LANBP_BASE_ADDR, TEMP8); EXE_SET(); // Execute Set } Appendix C Standard Firewall Platform Setting C-11
N e t w o r k Ap p l i a n c e FWS-2200 /* Set Watch Dog as LAN3 & 4 By Pass mode */ VOID WDT_LAN34_BP() { UINT8 TEMP8; SEL_PAIR(0x01) ; // Select Pair II TEMP8 = IoIn8(LANBP_BASE_ADDR) | 0x40; IoOut8(LANBP_BASE_ADDR, TEMP8); EXE_SET(); // Execute Set } /* Set Watch Dog as system reset mode */ VOID WDT_RESET() { UINT8 TEMP8; SEL_PAIR(0x00) ; // Select Pair I TEMP8 = IoIn8(LANBP_BASE_ADDR) & 0xBF; IoOut8(LANBP_BASE_ADDR, TEMP8); Appendix C Standard Firewall Platform Setting C-12
N e t w o r k Ap p l i a n c e SEL_PAIR(0x00) ; FWS-2200 // Select Pair II IoOut8(LANBP_BASE_ADDR, TEMP8); EXE_SET(); // Execute Set } Appendix C Standard Firewall Platform Setting C-13
N e t w o r k Ap p l i a n c e FWS-2200 C.4 Console Redirection Console redirection allows you to maintain a system from a remote location by re-directing keyboard input and text output through the serial port. This section will tell you how to use the console redirection. 1. Please insert console cable between on FWS-2200 and remote client system. 2.
N e t w o r k Ap p l i a n c e FWS-2200 Step3 - Click OK Step4 - From the connect to pull-down menu, select a COM port available on your client system and click OK Step5 - Select Baud Rate >> 19200, Flow control >> None, Data bit >>8, Parity cheek >> None, Stop bit>>1 4. Power on FWS-2200 and it will display the BIOS information on the client system.
N e t w o r k Ap p l i a n c e FWS-2200 Appendix D AHCI Settings Appendix D AHCI Settings D-1
N e t w o r k Ap p l i a n c e FWS-2200 D.
N e t w o r k Ap p l i a n c e FWS-2200 Step 3: The setting procedures “ In BIOS Setup Menu” A: Advanced -> IDE Configuration -> ATA Or IDE Configuration -> Enhanced B: Configure SATA As -> AHCI Step 4: The setting procedures “In BIOS Setup Menu” B: Boot -> Boot Option #1 -> DVD-ROM Type Appendix D AHCI Settings D-3
N e t w o r k Ap p l i a n c e FWS-2200 Step 5: The setting procedures “In BIOS Setup Menu” C: Save & Exit -> Save Changes and Exit Step 6: Setup OS Appendix D AHCI Settings D-4
N e t w o r k Ap p l i a n c e FWS-2200 Step 7: Press “F6” Step 8: Choose “S” Appendix D AHCI Settings D-5
N e t w o r k Ap p l i a n c e FWS-2200 Step 9: Choose “Intel(R) ICH8-M-E/M SATA AHCI Controller” Step 10: It will show the model number you select and then press “ENTER” Appendix D AHCI Settings D-6
N e t w o r k Ap p l i a n c e FWS-2200 Step 11: Setup is loading files Appendix D AHCI Settings D-7
