Hardware Manual
Table Of Contents
- List of related manuals
- Table of contents
- Safety instructions
- Introduction to the manual
- Operation principle and hardware description
- Mechanical installation
- What this chapter contains
- Safety
- Examining the installation site
- Necessary tools
- Moving the drive
- Unpacking and examining the delivery (frames R1 to R5)
- Unpacking and examining the delivery (frames R6 to R9)
- Installing the drive
- Flange mounting
- Cabinet installation
- Cooling
- Grounding inside the cabinet
- Installing drives above one another
- Planning the electrical installation
- What this chapter contains
- Limitation of liability
- Selecting the supply disconnecting device
- Selecting and dimensioning the main contactor
- Checking the compatibility of the motor and drive
- Protecting the motor insulation and bearings
- Requirements table
- Additional requirements for ABB motors of types other than M2_, M3_, M4_, HX_ and AM_
- Additional requirements for ABB high-output and IP23 motors
- Additional requirements for non-ABB high-output and IP23 motors
- Additional data for calculating the rise time and the peak line-to-line voltage
- Additional note for sine filters
- Selecting the power cables
- Selecting the control cables
- Routing the cables
- Implementing thermal overload and short-circuit protection
- Protecting the drive against ground faults
- Connecting drives to a common DC system
- Implementing the Emergency stop function
- Implementing the Safe torque off function
- Implementing the safety functions with the FSO module
- Implementing the ATEX-certified Safe motor disconnection function (option +Q971)
- Implementing the Power-loss ride-through function
- Using power factor compensation capacitors with the drive
- Using a contactor between the drive and the motor
- Implementing a bypass connection
- Protecting the contacts of relay outputs
- Connecting a motor temperature sensor to the drive I/O
- Electrical installation
- What this chapter contains
- Warnings
- Checking the insulation of the assembly
- Checking the compatibility with IT (ungrounded) systems
- Connecting the power cables
- DC connection
- Connecting the control cables
- Connecting a PC
- Controlling several drives through panel bus
- Installing optional modules
- Installation checklist
- Start-up
- Fault tracing
- Maintenance
- What this chapter contains
- Maintenance intervals
- Heatsink
- Fans
- Replacing the main cooling fan of frames R1 to R3
- Replacing the auxiliary cooling fan of IP55 frames R1 to R3
- Replacing the main cooling fan of frames R4 and R5
- Replacing the auxiliary cooling fan of frames R4 and R5 (IP55 and option +C135) and IP21 frame R5 types ACS880-01-xxxx-7
- Replacing the main cooling fan of frames R6 to R8
- Replacing the auxiliary cooling fan of frames R6 to R9
- Replacing the IP55 auxiliary cooling fan of frames R8 and R9
- Replacing the main cooling fans of frame R9
- Replacing the drive (IP21, UL Type 1, frames R1 to R9)
- Capacitors
- Memory unit
- Replacing the control panel battery
- Replacing safety functions modules (FSO-12, option +Q973)
- Technical data
- What this chapter contains
- Marine type-approved drives (option +C132)
- Ratings
- Derating
- Ambient temperature derating
- IP21 (UL Type 1) drive types and other IP55 (UL Type 12) types than listed in the following subheadings
- IP55 (UL Type 12) drive types -274A-2, 293A-3, -260A-5, -302A-5 and -174A-7
- IP55 (UL Type 12) drive type -240A-5
- IP55 (UL Type 12) drive types -363A-3 and -361A-5
- IP55 (UL Type 12) drive type -210A-7
- IP55 (UL Type 12) types -0430A-3, -0414A-5 and -0271A-7
- Altitude derating
- Deratings for special settings in the drive control program
- Ambient temperature derating
- Fuses (IEC)
- Fuses (UL)
- Dimensions. weights and free space requirements
- Losses, cooling data and noise
- Terminal and lead-through data for the power cables
- Terminal data for the control cables
- Electrical power network specification
- Motor connection data
- Control unit (ZCU-12) connection data
- Efficiency
- Protection classes
- Ambient conditions
- Materials
- Applicable standards
- CE marking
- Compliance with the EN 61800-3:2004
- UL marking
- “C-tick” marking
- EAC marking
- Approvals
- Cyber security disclaimer
- Disclaimer
- Dimension drawings
- What this chapter contains
- Frame R1 (IP21, UL Type 1)
- Frame R1 (IP55, UL Type 12)
- Frame R2 (IP21, UL Type 1)
- Frame R2 (IP55, UL Type 12)
- Frame R3 (IP21, UL Type 1)
- Frame R3 (IP55, UL Type 12)
- Frame R4 (IP21, UL Type 1)
- Frame R4 (IP55, UL Type 12)
- Frame R5 (IP21, UL Type 1)
- Frame R5 (IP55, UL Type 12)
- Frame R6 (IP21, UL Type 1)
- Frame R6 (IP55, UL Type 12)
- Frame R7 (IP21, UL Type 1)
- Frame R7 (IP55, UL Type 12)
- Frame R8 (IP21, UL Type 1)
- Frame R8 (IP55, UL Type 12)
- Frame R9 (IP21, UL Type 1)
- Frame R9 (IP55, UL Type 12)
- Safe Torque off function
- Resistor braking
- What this chapter contains
- Operation principle and hardware description
- Planning the braking system
- Mechanical installation
- Electrical installation
- Start-up
- Technical data
- Dimensions and weights of external resistors
- Common mode, du/dt and sine filters
- Further information
180 Technical data
Drive type
ACS880-01…
Input
current
Fuse (one fuse per phase)
A A V Manufacturer Type UL class
U
N
= 230 V
04A6-2 4.4 15 600 Bussmann JJS-15 T
06A6-2 6.3 15 600 Bussmann JJS-15 T
07A5-2 7.1 15 600 Bussmann JJS-15 T
10A6-2 10.1 20 600 Bussmann JJS-20 T
16A8-2 16.0 25 600 Bussmann JJS-25 T
24A3-2 23.1 40 600 Bussmann JJS-40 T
031A-2 29.3 50 600 Bussmann JJS-50 T
046A-2 44 80 600 Bussmann JJS-80 T
061A-2 58 100 600 Bussmann JJS-100 T
075A-2 71 125 600 Bussmann JJS-125 T
087A-2 83 125 600 Bussmann JJS-125 T
115A-2 109 150 600 Bussmann JJS-150 T
145A-2 138 200 600 Bussmann JJS-200 T
170A-2 162 250 600 Bussmann JJS-250 T
206A-2 196 300 600 Bussmann JJS-300 T
274A-2 260 400 600 Bussmann JJS-400 T
U
N
= 460 V
02A1-5 2.1 3 600 Bussmann JJS-3 T
03A0-5 3.0 6 600 Bussmann JJS-6 T
03A4-5 3.4 6 600 Bussmann JJS-6 T
04A8-5 4.8 10 600 Bussmann JJS-10 T
05A2-5 5.2 10 600 Bussmann JJS-10 T
07A6-5 7.6 15 600 Bussmann JJS-15 T
11A0-5 11 20 600 Bussmann JJS-20 T
014A-5 14 25 600 Bussmann JJS-25 T
021A-5 21 35 600 Bussmann JJS-35 T
027A-5 27 40 600 Bussmann JJS-40 T
034A-5 34 50 600 Bussmann JJS-50 T
040A-5 40 60 600 Bussmann JJS-60 T
052A-5 52 80 600 Bussmann JJS-80 T
065A-5 65 90 600 Bussmann JJS-90 T
077A-5 77 110 600 Bussmann JJS-110 T
096A-5 96 150 600 Bussmann JJS-150 T
124A-5 124 200 600 Bussmann JJS-200 T
156A-5 156 225 600 Bussmann JJS-225 T
180A-5 180 300 600 Bussmann JJS-300 T
240A-5 240 350 600 Bussmann JJS-350 T
260A-5 260 400 600 Bussmann JJS-400 T