2-YEAR WARRANTY INSTRUCTION MANUAL Climatouch™ CT0-7TC-32 3 Heating and 2 Cooling with Dual Fuel Switch www.CLIMATOUCH.
OUTDOOR WIRELESS TEMPERATURE TRAN SMITTER AND REC EIVER KIT Climatouch™ Part No. 90064 Accurately Displays Current Outdoor Temperature on the Climatouch™ Thermostat and Enables Dual Fuel Capability Outdoor Wireless Temperature Transmitter and Receiver Kit Includes: Transmitter Antenna Receiver Module 2 AA Batteries U.S.
TABLE OF CONTENTS COMF ORT CONVEN IENCE CONT ROL Introducing the Climatouch™ CT0-7TC-32 touch-screen thermostat with 3-stage heating, 2-stage cooling control, and fossil fuel switch (available only when combined with Climatouch™ Outdoor Wireless Transmitter and Receiver Kit. Climatouch™ Part No.
GLOSSARY OF TERMS SELECTING A LOCATION CYCLE RATE - Cycle rate is the frequency that heating or cooling equipment is turned on during a certain period of time. Cycle rate is often given in units of cycles per hour (CPH). Install your Climatouch™ thermostat approximately 5 feet (1.5 meters) above the floor in an area with good air circulation. DIFFERENTIAL - Differential is defined as the difference between the cut-in and cut-out points as measured at the thermostat under specified operating conditions.
MOUNTING CLIMATOUCH™ TO THE WALL 1. Make sure to turn off the power supply located at the electrical service panel. All heating and cooling units should be OFF. 2. Separate the backplate from the thermostat by grasping the unit firmly at the bottom lip and pulling gently until the two piece are apart. 3. Align the backplate to the wall. 4. Mark the three locations for drilling the 3/16” holes required for the plastic screw anchors.
WIRING DIAGRAMS WIRING DIAGRAMS ONE AC AC AND ONE HEAT 24V (RED) 24V (RED) Heat (WHT) Fan (GRN) COMMON (BLUE) AC (YLW) TWO AC Fan (GRN) COMMON (BLUE) AC (YLW) AC AND TWO HEAT AC2 (YLW) 24V (RED) 24V (RED) Heat2 Heat1 (WHT) Fan (GRN) COMMON (BLUE) 10 AC1 (YLW) Climatouch™ CT0-7TC-32 Fan (GRN) COMMON (BLUE) INSTRUCTION MANUAL AC (YLW) 11
WIRING DIAGRAMS WIRING DIAGRAMS AC AND TWO STAGE FURNACE ONE HEAT PUMP 24V (RED) 24V (RED) 2nd Stage Heat Reverse Valves (ORG) 1st Stage Heat (WHT) Fan (GRN) Fan (GRN) COMMON (BLUE) AC (YLW) COMMON (BLUE) HP (YLW) ONE HEAT PUMP AND ONE HEAT 24V (RED) Reverse Valves (ORG) Heat (WHT) Fan (GRN) COMMON (BLUE) 12 Climatouch™ CT0-7TC-32 INSTRUCTION MANUAL HP (YLW) 13
WIRING DIAGRAMS WIRING DIAGRAMS ONE HEAT PUMP AND TWO HEAT ONE TRANSFORMER Heat 2 24V (RED) Reverse Valves (ORG) Heat 1 (WHT) HEAT TRAN Fan (GRN) COMMON (BLUE) HP (YLW) TWO HEAT PUMP TWO TRANSFORMER CUT HP 2 24V (RED) Reverse Valves (ORG) Fan (GRN) COMMON (BLUE) 14 HP 1 (YLW) Climatouch™ CT0-7TC-32 COOL TRAN INSTRUCTION MANUAL HEAT TRAN 15
HOME SCREEN CONTROL SCREEN >> To access the CONTROL SCREEN, simply touch the HOME SCREEN Screen… anywhere! >> To return to the HOME SCREEN, simply touch icon at any time! >> From the CONTROL SCREEN, you can: >> The HOME SCREEN displays the following information: Change the Temperature Setpoint(s) using - and + buttons. In AUTO MODE toggle the Heat/Cool button (Heat or Cool will flash once selected), then raise or lower setpoints as desired.
TEMPERATURE CONTROL MODES >> Based on your HVAC equipment Climatouch can operate in the following temperature control modes - AUTO or HEAT or EMERGENCY HEAT or COOL or OFF AUTO - Climatouch™ keeps the room temperature between the selected HEAT and COOL setpoint INSTRUCTION MANUAL 19
FAN OPERATION MODES >> Climatouch ™ can operate the fan in one of the following three modes: FAN AUTO: The fan runs only when there is a demand for heating or cooling. FAN ON: The fan runs continuously FAN INTERMITTENT: The fan runs 10 minutes per 1/2 hour providing a convenient way to improve air quality and save energy. When the fan is running, the animated fan icon will appear on the HOME SCREEN.
MENU SCREEN MENU SCREEN >> To access the MENU SCREEN, simply touch MENU from the CONTROL SCREEN. >> From the MENU page, you can: Access DATE AND TIME SETTINGS to enter the accurate date and time Access VACATION SETTINGS to activate the VACATION MODE Access PROGRAM SETTINGS to pre-program temperature changes during each day of the week. Access FILTER MONITOR to review days of "fan run time.
DATE AND TIME SETTINGS PROGRAM SETTINGS Select the 12 OR 24 HOUR CLOCK display by pushing the corresponding button. Set the TIME by togggling hour, minute and AM/PM buttons. PROGRAM SETTINGS feature allows you to easily and quickly program daily temperature changes to fit your lifestyle and reduce energy consumption. You can customize the program for each day of the week with 4 independent temperature and fan operation settings per day.
ENERGY WATCH SET SCREEN OPTIONS ENERGY WATCH feature provides a report on the energy consumption and the dollar cost of operating your HVAC system (for up to the last 255 days). Once the cost of the kWH per compressor, furnace and fan have been entered into the ENERGY WATCH Settings (see page 32) Energy Watch will display the consumption as well as the real time dollar cost of the HVAC system. Otherwise, ENERGY WATCH will display only the total time the Compressor and the Furnace have been operating.
VACATION MODE FILTER MONITOR >> VACATION SETTINGS allows you to set the temperature to a fixed setpoint during the time you are on vacation, providing energy savings without compromising comfort upon your return. IMPORTANT: HEAT or COOL must be selected from the CONTROL SCREEN before entering the Vacation Settings screen. To begin select Vacation Mode ON: FILTER MONITOR: Displays filter usage in days RESET: Resets filter timer (You should reset FILTER MONITOR after changing the air filter.
ADVANCED SETTINGS - FEATURES SETTINGS :: DAYLIGHT TIME: Choose Daylight Time ON or OFF dependent on your Time Zone. FILTER: Enter the air filter "fan run time" information here. The Filter Monitor feature uses this information to inform you when to change your air filter by displaying CHANGE FILTER icon on the HOME SCREEN.
ADVANCED SETTINGS - SYSTEM CONFIGURATION ADVANCED SETTINGS - DUAL FUEL SWITCH ! IMPORTANT: By inadvertently modifying system configuration settings, you ! IMPORTANT: This feature can only be activated when used with the Climatouch ™ may seriously degrade HVAC system performance. Outdoor Wireless Temperature Transmitter and Receiver. Please install the Climatouch™ Outdoor Wireless Temperature Transmitter and Receiver before activating this feature.
ADVANCED SETTINGS - TIMER FEATURE :: Specify the number of minutes for which Stage 1 will function until Stage 2 is activated to help raise (or cool) temperature (if the temperature set point is not reached). This unique function avoids excess compressor wear in the case where the necessary temperature set point is not met through setting of the Staging Differential. Set to “00” to disable.
ADVANCED SETTINGS - HEAT PUMP :: HP ON when Furnace On: Heat Pump and Furnace can operate together when 2nd stage furnace is required. HP “OFF” when Furnace On: turns off the Heat Pump when the furnace is On (required on some gas or oil furnaces).
ADVANCED SETTINGS - CALIBRATION ADVANCED SETTINGS - CALIBRATION >> Calibration of Temperature >> Temperature Calibration Table Your Climatouch™ Thermostat is rated for an accuracy of +/-1°F (+/-1°C). :: Determine the temperature difference using an accurate thermometer, then use the following table to adjust your thermostat calibration. If you have determined due to drafts, sunlight or other environmental factors that your thermostat requires calibration, follow this easy guide.
SIMPLE THERMOSTAT MODE TROUBLESHOOTING ? Touch screen buttons do not function properly. Remove cover, press the reset button located in the bottom left corner then accurately touch 3 target centers on the screen when prompted. ? Air conditioning turns on in HEAT mode and heating turns on in COOL mode. Reverse the OB valve (see “Advanced Settings” Page 36). ? PARTIAL LOCK and FULL LOCK do not function. You must not touch the screen for 1 minute for Climatouch™ to automatically lock.
IMPORTANT NOTICE WARRANTY >> WHEN USING THIS THERMOSTAT WITH A GAS FURNACE A COMMON WIRE (C) HARDWARE AED Electronics, Inc. warrants the original end user (“Customer”) that new Climatouch™ branded products will be free from defects in workmanship and materials, under normal use, for two (2) years from the original purchase date. MUST BE CONNECTED. When working without a common wire: >> A confirm in HEAT MODE the cooling does not switch on or B confirm in COOL MODE the heat does not switch on.
TECHNICAL SUPPORT: 1-866-90TOUCH (1-866-908-6824) PHYSICAL DIMENSIONS Case: 5.75” x 4.75” x 1.25” (145mm x 120mm x 30mm) Screen: 4.1875” (106mm) ELECTRICAL RATING 24 volt AC/DC Class 2 maximum 4 amps Temperature Accuracy ±1°F (±0.5°C) Humidity Accuracy ±5%RH PATENTS 7,156,318; 7,145,110; 7,050,026; 7,028,912; 6,902,117; 6,786,421; Other Patents Pending CT0-7TC-32 MANUAL PRINTED IN CHINA AED Electronics, Inc. 5758 Royalmount Ave.