000BASE-LX Gigabit Uplink Module EM4582-LX-SC Quick Installation Guide
Quick Installation Guide EM4582-LX-SC Gigabit Uplink Module Slide-in module with 1 1000BASE-LX (SC-type) port
Copyright © 2000 by Accton Technology Corporation. All rights reserved. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Accton Technology Corporation. Accton makes no warranties with respect to this documentation and disclaims any implied warranties of merchantability, quality, or fitness for any particular purpose. The information in this document is subject to change without notice.
Contents Description of Hardware Gigabit Uplink Module Gigabit Port LEDs 1 1 1 Installing the Module Package Contents Handling the Module Instructions 2 2 2 2 Maximum Cable Lengths 5 Troubleshooting 6 Product Specifications 6 EMI Certification FCC Class A Certification (USA) Canada Department of Communications - Class A BSMI Class A (Taiwan) VCCI Class A Compliance (Japan) CE Mark Declaration of Conformance for EMI and Safety (EEC) 7 7 7 7 7 8 Safety Compliance Warning: Fiber Optic Port Safety A
Contents ii
Description of Hardware Gigabit Uplink Module The EM4582-LX-SC fiber optic module is designed for use in Accton switch models which have a single-port Gigabit Ethernet transceiver slot. At present, suitable units include these CheetahSwitch Workgroup models – ES3514F, ES3526F, ES3526G, and ES3552. Detailed information about configuring these modules and advice about Fast Ethernet configuration rules can be found in the switch’s user guide.
User Guide Installing the Module Caution: Do not install this module in any unit other than the ES3514F, ES3526F, ES3526G, or ES3552. Contact your distributor for advice on newly released switches which may be designed for use with these modules. The EM4582-LX-SC fiber optic module is field installable. Just follow the instructions below.
Installing the Module Keep the original faceplate for future use. If you should remove the module, replace the faceplate to prevent dust and debris from entering the unit and to maintain proper air flow. 5. Insert the new module into the switch: Holding the new module with the text on the front panel upright, carefully slide the module into a lower slot on the rear panel, and press gently until it snaps into place. Be sure the new module’s front panel is flush with the switch panel.
User Guide 6. Secure the new module: Secure the new module in place by screwing the attached screws clockwise into the switch’s chassis. Tighten them enough to secure the module, but not so tight as to prevent them from being unscrewed by hand. 7. Connect the network cable to the module: Connect fiber cable to the port on the newly installed module. See “Maximum Cable Length” on page 5 in this guide for further information. 8.
Maximum Cable Lengths Maximum Cable Lengths Cable Types and Specifications Cable Type Max. Length Connector 10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45 100BASE-TX Cat. 5 100-ohm UTP 100 m (328 ft) RJ-45 100BASE-FX 50/125 or 62.5/125 micron core multimode fiber Half duplex 412 m (1,351 ft.) SC or ST Full duplex 2 km (1.24 miles) SC or ST 1000BASE-SX 50/125 or 62.5/125 micron core multimode fiber See the SC or ST 1000BASE-SX table 1000BASE-LX 50/125 or 62.
User Guide Troubleshooting If you experience any problems with the module, check the following items before contacting Accton Technical Support: • • • • Ensure the switch with the fiber optic module is powered up. Ensure that the device attached to the module is powered up and operating correctly. Ensure that the module is properly seated in the slot. Verify that the module port is configured to match the communication mode used by the attached device (full or half duplex).
EMI Certification EMI Certification FCC Class A Certification (USA) Warning: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications.
User Guide CE Mark Declaration of Conformance for EMI and Safety (EEC) This is to certify that this product complies with ISO/IEC Guide 22 and EN45014. It conforms to the following specifications: EMC: EN55022(1988)/CISPR-22(1985) EN60555-2(1995) EN60555-3 IEC1000-4-2(1995) IEC1000-4-3(1995) IEC1000-4-4(1995) IEC1000-4-6(1995) class A class A 4kV CD, 8kV AD 3V/m 1kV - (power line), 0.
Safety Compliance Underwriters Laboratories Inc. (USA) Important! Before making connections, make sure you have the correct Cord Set. Check it (read the label on the cable) against the following specification list.
User Guide Warranty Accton warrants to the original owner that the product delivered in this package will be free from defects in material and workmanship for a period of three (3) years from the date of purchase from Accton or it’s Authorized reseller. For the warranty to apply, you must register your purchase by returning the registration card indicating the date of purchase and including proof of purchase.
EM4582-LX-SC E102000-R01 150514-102
