Specifications

16
116-31 (Globe) / 1116-31 (Angle)
PRESSURE SUSTAINING / SOLENOID ON-OFF
Installed in a mainline it prevents upstream pressure from dropping
below a preset minimum. Solenoid override of the sustaining function
allows for electrical on-off operation.
NOTE:
Adjustment range:
Standard: 20-200 psig
Optional: 0-30 psig,100-300 psig
Solenoid max. W.P.:
At time of order, advise factory actual system working pressure for
correct solenoid selection. (consult factory if over 150 psig.)
Enclosure: NEMA 1, 2, 3, 3S, 4, 4X
Optional: Explosion proof
NEMA 3, 3S, 4, 4X, 6, 6P, 7, 9
Specify energized to open or energized to close main valve.
QUICK SIZING: Valve size same size as line.
Points to consider: –
– Refer to Engineering Data - Flow Capacity Chart
– Pressure drop at required flow
Refer to Engineering Data - Pressure Drop Chart
PRESSURE RELIEF / SUSTAINING
116 (Globe) / 1116 (Angle)
PRESSURE RELIEF / SUSTAINING
Installed on a by-pass line, mainline pressure is accurately controlled
by relief of excess pressure. Installed in a mainline it prevents
upstream pressure from dropping below a preset minimum.
NOTE:
Adjustment range:
Standard: 20-200 psig
Optional: 0-30 psig
100-300 psig
Additional relief/sustaining
functions:
- 116FM/1116FM
(U.L. listed/F.M. approved for fire
pump relief service)
- 116-5 Pressure Sustaining /Check
- 116-25 Differential Pressure
Sustaining
- 116-24 Differential Pressure
Sustaining / Check
116 RELIEF
QUICK SIZING: Valve size one or two sizes smaller than main line.
Points to consider:
– Refer to Engineering Data - Flow Capacity Chart.
– If valve size required is smaller than line size, consider ACV 6116.
Consult Watts ACV representative/factory.
116 SUSTAINING
QUICK SIZING: Valve size same as line.
Points to consider:
– Refer to Engineering Data - Flow Capacity
Chart Pressure drop at required flow
– Refer to Engineering Data - Pressure Drop Chart
V
ALVE FUNCTION
– Maintain constant upstream pressure (inlet to valve) by relieving excess pressure
COMPONENTS 1. Main Valve
2
. Sustaining Control
3. Adj. Closing Speed
ACCESSORIES
Located as indicated ❏ X - Isolation Cocks ❏ FC - Flo-Clean Strainer
Included as marked ❏ Y - Y Strainer ❏ L - Limit Switch
❏ P - Position Indicator ❏ AOS - Adj. Opening Speed
VALVE SIZE – INCHES 1 1/4 1 1/2 2 2 1/2 34 6 810 12 14 16
MAXIMUM CONTINUOUS
93 125 208 300 460 800 1800 3100 4900 7000 8500 11000
FLOW RATE GPM (WATER)
MAXIMUM INTERMITTENT
210 280 460 650 1000 1800 4000 7000 11000 16000 19000 25000
FLOW RATE GPM (WATER)
VALVE FUNCTION
– Maintain constant upstream pressure (inlet to valve) by relieving excess pressure
– Solenoid provides electrical on/off override of relief/sustaining function
COMPONENTS 1. Main Valve
2. Sustaining Control
3. Adj. Restriction - Closing
4. 2-Way Solenoid
ACCESSORIES
Located as indicated ❏ AOS - Adj. Opening Speed ❏ L - Limit Switch
Included as marked ❏ X - Isolation Cocks ❏ P - Position Indicator
❏ Y - Y Strainer ❏ FC - Flo-Clean Strainer
Flow Direction Shown: Under the Seat
Optional ‘R’ Flow Over the Seat: 116-31R/1116-31R
F
low Direction Shown: Under the Seat