User guide

ManualsBrandsADS-TEC ManualsComputersVMT6010/6012/6015

UserManual

Terminals

VMT6010/6012/6015

Version1.4

Summary of content (48 pages)

PAGE 1
Version 1.
PAGE 2
VMT6010/6012/6015 1 Index 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 2.5 3 3.1 3.2 3.3 4 4.1 4.2 4.3 5 5.1 5.2 5.3 5.4 5.5 5.6 5.
PAGE 3
VMT6010/6012/6015 6 Interfaces 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 Interface Setup 24V DC Power Supply Autostart (S1) Speakers USB‐Interface PS/2 Interface Netzwork Connection (RJ45) Optional Radio Network Card Serial COM Interface (RS232) 2 24 24 24 26 27 28 28 29 30 31 7 Drives 32 8 Software‐/Driver‐Installation 33 8.1 Configuration Center 8.1.1 Automatic Brightness Adaption 8.1.2 COM Input Configuration 8.1.3 Ignition 8.1.4 USB‐Lock Function 8.1.5 On/Off Button Configuration 8.1.
PAGE 4
VMT6010/6012/6015 3 1 Remarks 1.1 Relevant Documentation for this device The following documents are essential for setting up and operating this device: User Manual (This Documentation): Contains information for installation, commissioning and operating the device along with technical data of the device hardware. Qucik Start Guide: Quick Install Guide for fast commissioning. 1.
PAGE 5
VMT6010/6012/6015 4 1.5 Copyright This manual, including all contained figures, is protected by copyright law. Any use for third parties non‐ compliant with the copyright provisions is prohibited. Any reproduction, translation as well as electronic and photographic archiving and modification shall only be permitted after explicit written authorisation by ads‐tec GmbH. Any party in violation of this provision shall be obliged to damage compensation. 1.
PAGE 6
VMT6010/6012/6015 1.7 Standards This device complies with the requirements and protective aims of the following EC regulations: Standards  This device meets the test requirements for granting the CE sign according to the European test standards EN 61000‐6‐4 and EN 61000‐6‐2  This device complies with the test requirements in accordance with EN 60950 (VDE0805, IEC950) "Safety of Information Technology Equipment"  The device meets the EN 60068‐2‐6 test requirements (sinus excitation).
PAGE 7
VMT6010/6012/6015 1.9 Scope of Delivery Please check that all of the following components are contained in the packaging: Scope of Delivery VMT6000 series  1 x device  4‐pin Lead‐through connector from Phoenix Contact, COMBICON MC 1,5/4‐STF3.81  Service CD  Protective covers Optional scope of delivery:  Operating system  Installation kit © ads‐tec GmbH • Raiffeisenstr.
PAGE 8
VMT6010/6012/6015 7 2 Notes on Operation & Safety This device contains electrical voltages and extremely sensitive components. Intervention by the user is only designated for establishing the required cable connections. The manufacturer or a service partner authorised by the manufacturer should be consulted if you plan to make further modifications. Before beginning any works on this device, it must be disconnected from the power supply.
PAGE 9
VMT6010/6012/6015 2.2 Damage Caused By Improper Use This device must immediately be shut down and protected from any accidental commissioning if the operating system shows any obvious damage caused by, for example, improper operating or storage conditions, or by improper use or handling. 2.3 Warranty / Repair During the warranty period, any repair must only be carried out by the manufacturer or by a person authorised by the manufacturer. 2.
PAGE 13
VMT6010/6012/6015 12 4 Commissioning The power supply connection and interfaces of this device are installed underneath a protective cover. This cover has to be removed in order to connect the power supply lead and the interface cables. All supply leads and all required data leads have to be connected before commissioning. All supply leads and all required data leads have to be connected before commissioning.
PAGE 14
VMT6010/6012/6015 13 Note: If the case is connected with earth potential at the provided PE contact (e.g. by connecting the PE contact with the device plug), the electrical insulation is no longer given. This also applies if the device is installed by using a metal retainer clip. If you want to have the device electrically insulated from the power supply, you have to use a method of installation that ensures appropriate insulation.
PAGE 15
VMT6010/6012/6015 Abb. 6: Warning: The indicated protection class is only fully guaranteed if the case cover is correctly installed! Pos: 19 /Datentechnik/Inbetriebnahme/Betriebsbereitschaft prüfen/Betriebsbereitschaft prüfen für OPC/CPC/PLC/OTC/ITC/VMT-Serie(+Monitore) / IPC 5100/5500/2400/1100 @ 0\mod_1158905578361_6.doc @ 381 @ 4.
PAGE 16
VMT6010/6012/6015 15 5 Operation 5.1 Frontkeys Control Keys Abb. 7: Version 1 (State until Q1/2010) ON / OFF pushbutton of the device (ATX functionality) The operating system is shut down, but the device is not disconnected from the input voltage. Depending on the actual equipment version, each device is equipped with an operating system (Windows CE 6.0, Windows XP embedded or Windows XP Professional) ex works, and a soft keyboard is installed.
PAGE 17
VMT6010/6012/6015 16 Note: If the software keyboard is not installed, only the functions for display settings and volume control are active. When changing the values, no representation is visible on the screen. The key functions can have been previously modified in accordance with customer specific requirements. The above described functions are pre‐set ex works.
PAGE 18
VMT6010/6012/6015 17 Note: If the software keyboard is not installed, only the functions for display settings and volume control are active. When changing the values, no representation is visible on the screen. The key functions can have been previously modified in accordance with customer specific requirements. The above described functions are pre‐set ex works. Pos: 21 /Datentechnik/Bedienung/Softkeyboard/Softkeyboard für VMT 60xx @ 1\mod_1228750145198_6.doc @ 4251 @ 5.
PAGE 19
VMT6010/6012/6015 18 How to operate the Soft Keyboard from Version 3.11:: Activate and deactivate the soft keyboard for letter/character input using the touch screen Switches numeric keys on and off (only if numeric keys are visible) Switching between different representations (Alphanumeric keys  Numeric keys  Function key bar) Soft keyboard representation, zoom in Soft keyboard representation, zoom out Note: If a function is to be activated which requires pressing two keys at the same time (e.g.
PAGE 20
VMT6010/6012/6015 19 5.4 Status Indicators SYS‐LED (Bicoloured) Depending on the colour and type of flashing, different device states are displayed by the SYS LED. Abb. 9: Folgende Signale werden dargestellt: System‐LED Indicators Behaviour static Lightsensor Pos: 24 /Datentechnik/Sondergeräte-Module/VMT6000-Serie/RFID-Reader für VMT6000-Serie @ 2\mod_1260527463758_6.doc @ 6885 @ © ads‐tec GmbH • Raiffeisenstr.
PAGE 21
VMT6010/6012/6015 20 5.5 RFID‐Reader (optional) By using the RFID reader, passive RFID TAGS (RFID chip / key card) are available for automatic system login. The user applies the RFID tag like a key and requires neither user name nor password. For authentication, the key card or the RFID chip are held in front of the position highlighted in the figure. The information from your key card or RFID chip is read and evaluated by the device. The VMT6000 series uses Mifare‐, and LEGIC Technology. Abb.
PAGE 22
VMT6010/6012/6015 21 5.6 RFID‐Configuration The equipment is pre‐configured to test the RFID functionality without configuration. Note: Check the functionality of your RFID reader through the following steps before starting the commissioning of a software to exclude any transport damage or other error sources. Depending on the hardware configuration a MIFARE or LEGIC RFID reader is installed.
PAGE 23
VMT6010/6012/6015 Abb. 12: If no RFID reader is found,you have the opportunity to select the serial port to which the RFID reader is connected manually. Abb. 13: After selection of the COM port, the application opens the por whicht is now ready to receive data. A transponder data are output in the surface. © ads‐tec GmbH • Raiffeisenstr.
PAGE 24
VMT6010/6012/6015 23 LEGIC 1) To test the RFID function, select a suitable editor (Notepad, Word) and hold the RFID tag to the RFID reader. This information will be issued. Note: . The output data can be pre customized in consultation with ads-tec 5.7 COMInput‐Configuration The Application COMInput converts the data received over a serial interface, in key sequences and feeds it then place in the Windows operating system.
PAGE 25
VMT6010/6012/6015 24 6 Interfaces 6.1 Interface Setup Interface IRQ Adress COM1 4 3F8h RFID (Touch) 3 2F8h Pos: 26 /Datentechnik/Schnittstellen/Spannungsversorgung/Spannungsversorgung für VMT60xx-Serie @ 2\mod_1260450284020_6.doc @ 6853 @ 6.2 24V DC Power Supply The supply voltage is provided via a lead‐through terminal including a screw connection (Phoenix Contact COMBICON MC 1,5/4‐STF3.81).
PAGE 26
VMT6010/6012/6015 25 Note: If the case is connected with earth potential at the provided PE contact (e.g. by connecting the PE contact with the device plug), the electrical insulation is no longer given. This also applies if the device is installed by using a metal retainer clip. If you want to have the device electrically insulated from the power supply, you have to use a method of installation that ensures appropriate insulation.
PAGE 27
VMT6010/6012/6015 26 Zündungsfunktion (Ignition) The device is capable of being externally started by using an additional signal input. This function is well known from the automotive industry (switch‐on by using an ignition contact). The device is here continuously supplied with a 24 V DC power supply, and only if the additional signal is present at the ignition contact, e.g. as a result of turning the ignition key of the forklift, the computer is switched on or the blocking is released.
PAGE 28
VMT6010/6012/6015 6.4 Speakers The VMT 60xx has two internal speakers. Abb. 16: Note: The volume can be set up by using the device front keys. When activating the described key combinations, the volume level is modified. If the soft keyboard is installed, the system volume is additionally displayed by a display bar. Abb. 17: Pos: 29 /Datentechnik/Schnittstellen/USB-Anschluss/USB-Anschluss für VMT 60xx @ 2\mod_1260457598122_6.doc @ 6860 @ © ads‐tec GmbH • Raiffeisenstr.
PAGE 29
VMT6010/6012/6015 28 6.5 USB‐Interface The USB interfaces are used for connecting peripherals with USB connection. These interfaces comply with the USB 2.0 standard requirements. Pin‐Number Signal‐Name 1 VDC 2 D‐ 3 D+ 4 GND Note: The device supports a maximum of 8 external USB mass storage devices. If a USB Flash SSD is integrated, a maximum of 7 USB mass storage devices can be connected. Note: The USB interfaces can be individually locked by using the "Lock USB" software tool.
PAGE 30
VMT6010/6012/6015 29 Note: Since the timing of the integrated controller is specifically set up for cherry keyboards, keyboards of this manufacturer should preferably be used. If the soft keyboard is actively displayed on the monitor, the use of the external keyboard for control purposes is limited. The keyboard must be connected before switching the device on, because the keyboard interface is initialised in the process of booting.
PAGE 31
VMT6010/6012/6015 6.8 Optional Radio Network Card The device is equipped with a Mini PCI Express WLAN card with two antennas integrated in the front panel. The Mini PCI Express WLAN card supports the standards 802.11a/b/g. 802.11b/g: 11Mbit / 54Mbit, 2.4GHz 802.11a:54MBit, 5GHz Additionally, the following security standards are supported: WEP 64 bit, 128 bit 802.
PAGE 32
VMT6010/6012/6015 31 6.9 Serial COM Interface (RS232) Pos: 33 /Datentechnik/Schnittstellen/Serielle Schnittstelle COM RS232/Serielle Schnittstelle COM (RS232) für VMT 60xx @ 1\mod_1246373571514_6.doc @ 5876 @ The serial interface is used for digital data transmission. The RS232 interface can be connected by using a commercially available 9‐pin SUB‐D cable. Note: Pin 9 of the serial interface connector can be used for additional switching of a 5V power supply, e.g. for operating a serial barcode scanner.
PAGE 33
VMT6010/6012/6015 32 7 Drives The storage medium is selected according to the customer requirements. The following options are available for storage: Flash SSD: A Flash SSD with a storage capacity of at least 1GB is used. Its capacity depends on the desired operating system and the additional programmes to be installed. Hard disk: A 2.5" hard disk with at least 40 GB (UDMA) is used. On delivery, the hard disk is formatted in NTFS format (default for Windows XP).
PAGE 34
VMT6010/6012/6015 33 8 Software‐/Driver‐Installation The device will be delivered with a pre‐installed Windows / Linux operating system depending on what the customer wants. The drivers required for this are already installed and the operating system will be enabled by entering the licence information. Should an initial installation be required, please follow the following steps.
PAGE 35
VMT6010/6012/6015 TouchScreen Driver Installation Note: When installing the driver, you'll have to take in account that the touch screen monitor is internally connected with the USB interface! Touch screen monitor and PS2 mouse can be operated simultaneously. The installation has to be carried out as described below:  Switch on PC and boot.  Access the service CD by using the Explorer and start the Installer file in the TouchScreen folder.
PAGE 36
VMT6010/6012/6015 35 8.1 Configuration Center Configuration The start page of the Configuration Center provides you with an overview of which ads‐tec applications are installed on the device. Additionally, you can start any of these applications from the Configuration Center by double‐clicking on it Information In the Information section, device specific data like the device type, the firmware version and the serial number are listed.
PAGE 37
VMT6010/6012/6015 36 8.1.1 Automatic Brightness Adaption Note: The application of Automatic brightness adaptation allows the user to configure the respective display brightness. The display brightness can be changed manually, or alternatively automatically by enabling the Automatic brightness adaptation, which controls the brightness automatically depending on the ambient light level. Once the automatic brightness control is enabled, the brightness can no longer be modified by using the front keys.
PAGE 38
VMT6010/6012/6015 8.1.2 COM Input Configuration COM input configuration allows the application to verify the correct RFID function. By activation of COM2,the data is send automatically to an active application that uses the COM2 port forwarded. Note: Unnecessary applications that use the COM2 port must be stopped before running the COM input configuration. Because of different programming, data on various editors like Notepad or Word are represented differently. 8.1.
PAGE 39
VMT6010/6012/6015 38 8.1.4 USB‐Lock Function The USB lock function enables you to lock the USB ports, if required, and to avoid access by unauthorised people. Feedback In the Messaging section, you can set up whether a message should be output in the event that a USB port is locked or not. Additionally, the locking process can be logged in the event log Password Protection In order to avoid any unauthorised access to the USB Lock programme, the settings made can be provided with password protection.
PAGE 40
VMT6010/6012/6015 8.1.5 On/Off Button Configuration The ON / OFF pushbutton configuration allows to change the behaviour of the ON / OFF pushbutton. Regular Mode The ON / OFF pushbutton switched the device on and off Secure Mode The ON / OFF pushbutton only switches the device on. The switch‐off function is disabled Note: If the secure mode is used, the device can only be shut down by the software. © ads‐tec GmbH • Raiffeisenstr.
PAGE 41
VMT6010/6012/6015 8.1.6 Exemplary RFID Application The exemplary RFID application was developed in order to test the function of the RFID reader. Note: In the Interfaces section of the manual you can find more information about the topic of RFIDs. 8.1.7 Softkeyboard Here you can configure the soft keyboard application. A large variety of settings, like layout or commands can individually be adapted. All changes must be confirmed by pushing the Save button.. © ads‐tec GmbH • Raiffeisenstr.
PAGE 42
VMT6010/6012/6015 41 8.1.8 Screen Mob The Screen Mob application was developed in order to disable the touch screen of the device for a certain period of time. This function can be used for cleaning the touch screen. Pos: 38 /Datentechnik/Software / Treiber Installation/Softkeyboard/Softkeytastatur für alle Gerät ohne internes Laufwerk(CD/DVD) @ 0\mod_1159175310134_6.doc @ 667 @ 8.1.
PAGE 43
VMT6010/6012/6015 42 9 Technical Details Pos: 40 /Datentechnik/Service und Support/Service & Support @ 2\mod_1254312498746_6.doc @ 6472 @ Device Data VMT6008 Housing Powder coated aluminium diecast case Front Panel Fibreglass reinforced plastic, paint coated Display Resolution Displayable Colours Touch 10,4" LED 1024 x 768 Pixel max. 16,1 Mio. VMT6012 VMT6015 12,1" TFT 800 x 600 Pixel max. max. 256k Colours 15,1" TFT 1024 x 768 Pixel max. 16,1 Mio.
PAGE 44
VMT6010/6012/6015 43 10 Service & Support ads‐tec and its partner companies offer your customers a comprehensive service and support, which ensures availability of a fast and competent support with respect to all upcoming questions related to ads‐tec products or assemblies. Since the devices manufactured by ads‐tec are also used by associate companies, these devices might be configured in customer specific ways.