y o c u -tr a c k .c A. CHANGING THE BATTERY The Two-Way remote transmitter is powered by one “AAA” Battery. When the power of the battery weakens A icon shall be displayed on the LCD screen. When the old battery is replaced, there will be beep sounds to indicate the power is back up on the transmitter The One-way remote is powered by one CR2032 Battery. To replace battery use a coin or small flat blade screwdriver to carefully pry apart case. 1 .d o m o w w w .
y o c u -tr a c k .c B. STANDARD LCD ICON CONFIGURATIONS: Door Lock The lock icon will be displayed when the door are locked. Door Unlock and Disarmed The unlock icon will be displayed when the door are unlocked and disarmed System Armed Valet Mode All the function shall be temporally on hold.
y o c u -tr a c k .c Engine Cranking Your vehicle engine cranking by remote control. Engine Running Your vehicle’s engine is running Timer Control Start Engine starts automatically every 2 or 3 hours Timer with Temperature Control Start Engine starts automatically every 2 or 3 hours, it will start at a specified temperature at the end of the timed cycle. 24 hour repeat with cold starting Monitor the temperature 24 hours.
y o c u -tr a c k .c C. REMOTE TRANSMITTER OPERATION: Button - - - 2.0 sec. - - 4 System Function Remark Arm & Lock Doors Press the Lock button for a half second Silent Arm & Lock Doors Press and hold for 1.0 seconds Panic Function Press and hold for 3 seconds to Activate or Deactivate panic function Arm and Warn-Away Bypass Arm and Warn-Away & Shock Sensor Bypass Arm and All Sensors Bypass Twice within Press 3 seconds. Press 3 times within 3 seconds.
y o c u -tr a c k .c Button System Function Activate or Deactivate the Remote Start Remark Press Press button once. - button if set to start safety mode. Runtime Reset - Timer Start Press and hold for 2 seconds Press the press button first then button. 24 hour repeat with cold starting Press the button first then press and hold button 1.
y o c u -tr a c k .c D. LCD REMOTE CONTROL: 1. Press the F button the number of times corresponding to the Level you wish to ) select; the LCD will display LEVEL number ( 2. Press the button while LEVEL number text is still on to perform the command. Button F x 1 Level 1 Tone / Vibrating Mode 1 sec. Vehicle’s Status Check /Alarm Report F x 2 Level 2 Button Beeper F x 3 Level 3 F x 4 Level 4 Button Lock Car 1 / Car 2 operation Voltage Check LCD Backlight 5 sec./ 10 sec.
y o c u -tr a c k .c Second Vehicle Security Operation: Press F button 4 times first then press button to enter Second Vehicle Security Mode, Under this mode press select CAR 2 operation ( operation and icon and button to text will display) or CAR 1 text will display. Vehicle’s Status Check /Alarm Report: Press F button 1 times first then press and hold buttons for 1 second until the beep confirms and then release the button. The LCD remote will display the current status of the vehicle.
y o c u -tr a c k .c E. CHIRP INDICATORS PARKING LIGHT Chirp Function Parking light Function 1 Chirp Arm 1 Flash Arm 2 Chirps Disarm 2 Flashes Disarm 3 Chirps Defective Reminder 3 Flashes Disarm / Triggered Warning 4 Chirps Disarm / Triggered Warning 12 Flashes Car Finder 6 Chirps Car Finder Constant On Under Remote Start F.
y o c u -tr a c k .c G. TABLE OF ZONE / ALARM DIAGNOTICS H. Situation Situation LED On Duty Zone 1 (Door Triggered) 1 flashes, break, then repeat Zone 2 (Trunk Triggered) 2 flashes, break, then repeat Zone 3 (Hood Triggered) 3 flashes, break, then repeat Zone 4 (Shock Triggered) 4 flashes, break, then repeat Zone 5 (Tilt Triggered) 5 flashes, break, then repeat Zone 6 (Ignition Triggered) 6 flashes, break, then repeat ACTIVE ARMING – LOCK & ARM Press the button on the transmitter.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
