FSK53600Z USER MANUAL EN User Manual Dishwasher
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................6 4. CONTROL PANEL....................................................................................................... 7 5. PROGRAMMES...
ENGLISH 3 manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it.
ENGLISH • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • This appliance complies with the E.E.C. Directives. • UK and Ireland only. This appliance is fitted with a 13 A mains plug. If it is necessary to change the mains plug fuse, use only a 13 A ASTA (BS 1362) fuse. 2.3 Water connection • Do not cause damage to the water hoses.
www.aeg.com 3. PRODUCT DESCRIPTION 1 2 11 10 1 2 3 4 5 6 9 8 7 Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 3.1 Beam-on-Floor The Beam-on-Floor is a light that is displayed on the floor below the appliance door. • When the programme starts, a red light comes on and stays on for the duration of the programme. • When the programme is completed, a green light comes on. • When the appliance has a malfunction, the red light flashes.
ENGLISH 4. CONTROL PANEL 1 1 2 3 4 5 2 On/off button Display Delay button Programme button (up) Programme button (down) 3 4 6 7 8 9 5 6 7 8 9 TimeSaver button XtraDry button RESET button Indicators 4.1 Indicators Indicator Description Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates. 5. PROGRAMMES The numbering of the programmes in the table (P1, P2, etc.) reflects their sequence on the control panel.
www.aeg.com Programme Degree of soil Type of load Programme phases Options P4 • Fresh soil • Crockery and cutlery • Wash 60 °C or 65 °C • Rinses • XtraDry • Normal or light soil • Delicate crockery and glassware • Wash 45 °C • Rinses • Dry • XtraDry 3) P5 1) This programme offers the most efficient use of water and energy consumption for crockery and cutlery with normal soil. This is the standard programme for test institutes.
ENGLISH 9 6. SETTINGS 6.1 Programme selection mode and user mode When the appliance is in programme selection mode it is possible to set a programme and to enter the user mode. Settings available in the user mode: • The level of water softener according to the water hardness. • Activation or deactivation of the acoustic signal for the end of a programme. • Activation or deactivation of the rinse aid empty notification. • Activation or deactivation of AirDry.
www.aeg.com Regardless of the type of detergent used, set the proper water hardness level to keep the salt refill indicator active. Multi-tabs containing salt are not effective enough to soften hard water. How to set the water softener level Make sure the appliance is in user mode. repeatedly to change the 1. Press setting. 2. Press the on/off button to confirm the setting. 6.3 The rinse aid empty notification There is also an acoustic signal that sounds when the programme is completed.
ENGLISH How to deactivate AirDry 11 Press on/off to confirm the setting. Make sure the appliance is in user mode. 7. OPTIONS Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running. Not all options are compatible with each other. If you select non compatible options, the appliance automatically deactivates one or more of them. Only the indicators of the still active options are on.
www.aeg.com inside the appliance. Do not use detergent and do not load the baskets. After starting a programme, it may take up to 5 minutes for the appliance to recharge the resin in the water softener. It seems that the appliance is not working. The washing phase starts only after this procedure is completed. The procedure is repeated periodically. 6. Turn the cap of the salt container clockwise to close the salt container. 8.1 The salt container 8.
ENGLISH 13 You can turn the selector of the released quantity (B) between position 1 (lowest quantity) and position 4 or 6 (highest quantity). 9. DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5.
www.aeg.com 2. Press again and again until the display shows the delay time you want to set (from 1 to 24 hours). The delay indicator comes on. 3. Close the appliance door to start the countdown. While a countdown is running it is possible to increase the delay time but not to change the selection of the programme and options. When the countdown is completed, the programme starts. Opening the door while the appliance operates Opening the door while a programme is running stops the appliance.
ENGLISH • Select a programme according to the type of load and the degree of soil. offers the most efficient use of water and energy consumption. 10.2 Using salt, rinse aid and detergent • Only use salt, rinse aid and detergent for dishwasher. Other products can cause damage to the appliance. • In areas with hard and very hard water we recommend to use plain dishwasher detergent (powder, gel, tablets containing no additional agents), rinse aid and salt separately for optimal cleaning and drying results.
www.aeg.com After the programme is completed, water can still remain on the inside surfaces of the appliance. 11. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 11.1 Cleaning the filters The filter system is made of 3 parts. C 4.
ENGLISH 17 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 11.3 External cleaning 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. • Clean the appliance with a moist soft cloth. • Only use neutral detergents.
www.aeg.com Problem and alarm code Possible cause and solution You cannot activate the appliance. • Make sure that the mains plug is connected to the mains socket. • Make sure that there is no damaged fuse in the fuse box. The program does not start. • Make sure that the appliance door is closed. • If the delay start is set, cancel the setting or wait for the end of the countdown. • The appliance has started the procedure to recharge the resin inside the water softener.
ENGLISH 19 Problem and alarm code Possible cause and solution Rattling/knocking sounds from inside the appliance. • The tableware is not properly arranged in the baskets. Refer to basket loading leaflet. • Make sure that the spray arms can rotate freely. The appliance trips the circuit-beaker. • The amperage is insufficient to supply simultaneously all the appliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use.
www.aeg.com Problem Possible cause and solution The dishes are wet. • For the best drying performance activate the option XtraDry and set AirDry . • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty. • The quality of the rinse aid can be the cause. • The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and use rinse aid and multi-tablets together.
ENGLISH 21 Refer to "Before first use", "Daily use" or "Hints and tips" for other possible causes. 13. TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 596 / 818 - 898 / 550 Electrical connection 1) Voltage (V) 220 - 240 Frequency (Hz) 50 Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 13 Power consumption Left-on mode (W) 5.0 Off-mode (W) 0.
www.aeg.
ENGLISH 23
156915522-A-182018 www.aeg.
