LAVAMAT 74950A User manual Washing machine
Contents Thank you for choosing one of our high-quality products. To ensure optimal and regular performance of your appliance please read this instruction manual carefully. It will enable you to navigate all processes perfectly and most efficiently. To refer to this manual any time you need to, we recommend you to keep it in a safe place. And please pass it to any future owner of the appliance. We wish you much joy with your new appliance.
Safety information Environment concerns Packaging materials 36 37 Ecological hints 3 37 Subject to change without notice Operating instructions Safety information Read carefully & keep for future reference. • The safety of Your appliance complies with the industry standards and with legal requirements on the safety of appliances. However, as manufacturers, we feel it is our duty to provide the following safety notes.
Safety information Installation • This appliance is heavy. Care should be taken when moving it. • When unpacking the appliance, check that it is not damaged. If in doubt, do not use it and contact the Service Centre. • All packing and transit bolts must be removed before use. Serious damage can occur to the product and to property if this is not adhered to. See relevant section in the user manual.
Product description 5 • Make sure that children or pets do not climb into the drum. To prevent children or pets becoming trapped inside the drum the machine incorporates a special feature. To activate this device, rotate the button (without pressing it) inside the door clockwise until the groove is horizontal. If necessary use a coin. To disable this device and restore the possibility of closing the door, rotate the button anticlockwise until the groove is vertical.
Control panel Detergent dispenser drawer Compartment for detergent used for prewash . The prewash detergent is added at the beginning of the wash programme. Compartment for powder or liquid detergent used for main wash . Compartment for liquid additives (fabric softener, starch). Compartment for stain remover used for main wash with STAIN-option . Control panel Below is a picture of the control panel. It shows the programme selector dial as well as the buttons and the display.
7 START/PAUSE button ( START/PAUSE ) 8 DELAY START button ( DELAY START ) 9 Display Symbols on the control panel : = Handwash = Child Lock Display 9.1 9.2 9.3 9.4 9.9 9.5 9.6 9.7 9.8 9.1 - Temperature indicator and COLD symbol 9.2 - Spin Speed indicator, RINSE HOLD , NIGHT CYCLE - symbols , SPIN , 9.3 - Programme progress display: PREWASH , MAIN WASH , RINSE DRAIN , OVERDOSAGE • The programme progress display shows the washing phases of the selected programme.
First use • Delay start – The selected delay (20 hours max) set by means of the relevant button appears on the ’), then the duration of the previously display for about 3 seconds (for example selected programme is displayed. – The DELAY START symbol will appear on the display. – The delay time value decreases by one unit every hour and then, when remains 1 hour, the time decreases every minute.
Daily use 9 Child safety lock This device permits you to leave the appliance unattended and not to worry that children might be injured by or cause damage to the appliance. This function remains able also when the washing machine is not working. To enable (or disable) this option press simultaneously for about 6 seconds buttons 4 and 5 until the Child Lock symbol appears on (or disappears from) the display.
Daily use 2. If required, pour fabric softener into the compartment marked (the amount used must not exceed the MAX mark in the drawer). Close the drawer gently. Select the required programme by means of programme selector dial (1) You can choose the right programme for any type of laundry following the descriptions on the washing programme tables (see «Washing Programmes»). Turn the programme selector dial to the required programme. The programme selector determines the type of washing cycle (e.g.
Daily use 11 Select the spin speed, NIGHT CYCLE or RINSE HOLD option (button 3) When the required programme has been selected, your appliance automatically proposes the maximum spin speed provided for that programme. Press this button repeatedly to change the spin speed, if you want your laundry to be spun at a speed different from the one proposed by the washing machine. RINSE HOLD: by selecting this option the water of the last rinse is not emptied out to prevent the fabrics from creasing.
Daily use This option is recommended for heavily soiled laundry. STAIN option Select this option to treat heavily soiled or stained laundry with stain remover (extended main wash with time optimized stain action phase). The relevant symbol will appear on the display. This option is not available with a temperature lower than 40°C. If you wish to perform a programme with the stain option, pour stain remover into stain compartment marked with a blue arrow.
Daily use 13 If an incorrect option is selected, the yellow pilot light of the button 7 blinks 3 times and the message Err is displayed for a few seconds. Select the DELAY START (button 8) Before you start the programme , if you wish to delay the start, press the button repeatedly, to select the desired delay. The corresponding symbol will appear on the display. The wash programme can be delayed from 30 min - 60 min - 90 min, 2 hours and then by 1 hour up to a maximum of 20 hours by means of this button.
Washing programmes Opening the door after the programme has started First set the machine to pause by pressing the button 7 . • If the DOOR symbol disappears, the door can be opened; • If the DOOR symbol doesn’t go off, it means that the machine is already heating, that the water level is above the bottom edge of the door. In this case the door cannot be opened; • If you cannot open the door but you need to open it, you have to switch the machine .
Washing programmes Programme - Maximum and Minimum Temperature - Cycle Description - Maximum Fabrics Load - Type of Laundry Options HYGIENE ( HYGIENE) 60° Main wash - Rinses - Long spin at the maximum spin speed Max. load 8 kg The washing programme for white cottons. This program eliminates the micro-organisms thanks to the washing by 60°C and an additional rinse. In this way the action is more effective. Put into the compartment Stain a special additive for hygiene and select the option Stain.
Washing programmes Programme - Maximum and Minimum Temperature - Cycle Description - Maximum Fabrics Load - Type of Laundry Options EASY IRON PLUS (EASY IRON PLUS) 60° - Cold Main wash - Rinses - Short spin at 1200 rpm Max. load 1,5 kg Synthetic fabrics to be gentle washed and spun. Selecting this programme the laundry is gently washed and spun to avoid any creasing. In this way ironing is easier. Furthermore the machine will perform additional rinses.
Washing programmes Programme - Maximum and Minimum Temperature - Cycle Description - Maximum Fabrics Load - Type of Laundry Options SPIN SPIN Drain and long spin at the maximum spin speed Max. load 8 kg Separate spin for hand washed cotton garments and after programmes which ends with water left in the tub. Before selecting this programme the selector dial . You can choose the spin speed must be turned to by pressing the relevant button to adapt it to the fabrics to be spun.
Washing programmes Programme - Maximum and Minimum Temperature - Cycle Description - Maximum Fabrics Load - Type of Laundry Options SPORT INTENSIVE SPORT INTENSIVE 40° - Cold Prewash - Main wash - Rinses - Short spin at 1200 rpm Max. load 2.5 kg Special programme is suitable for washing heavily soiled sport items. The machine will add automatically a prewash phase before the main wash to eliminate mud stains.
Helpful hints and tips Programme - Maximum and Minimum Temperature - Cycle Description - Maximum Fabrics Load - Type of Laundry ECONOMY COTTONS ECONOMY 60° Main wash - Rinses - Long spin at the maximum spin speed Max. load 8 kg White and fast coloured cotton . This programme can be selected for slightly or normally soiled cotton items. The temperature will decrease and the washing time will be extended. This allows to obtain a good washing efficiency so saving energy.
Helpful hints and tips Rub particularly soiled areas with a special detergent or detergent paste. Treat curtains with special care. Remove hooks or tie them up in a bag or net. Maximum loads Recommended loads are indicated in the washing programme charts. General rules: • Cotton, linen: drum full but not too tightly packed; • Synthetics: drum no more than half full; • Delicate fabrics and woollens: drum no more than one third full.
Care and cleaning 21 Ink: depending on the type of ink, moisten the fabric first with acetone1), then with acetic acid; treat any residual marks on white fabrics with bleach and then rinse thoroughly. Tar stains: first treat with stain remover, methylated spirits or benzine, then rub with detergent paste. Detergents and additives Good washing results also depend on the choice of detergent and use of the correct quantities to avoid waste and protect the environment.
Care and cleaning Descaling The water we use normally contains lime. It is a good idea to periodically use a water softening powder in the machine. Do this separately from any laundry washing, and according to the softening powder manufacturer's instructions. This will help to prevent the formation of lime deposits. After each wash Leave the door open for a while. This helps to prevent mould and stagnant smells forming inside the appliance.
Care and cleaning 23 Washing drum Rust deposits in the drum may occur due to rusting foreign bodies in the washing or tap water containing iron. Do not clean the drum with acidic descaling agents, scouring agents containing chlorine or iron or steel wool. 1. Remove any rust deposits on the drum with a cleaning agent for stainless steel. 2. Run a washing cycle without any washing to clean off any cleaning agent residues. Programme: Short Cotton Programme at maximum temperature and add approx.
Care and cleaning 6. When no more water comes out, unscrew the pump and remove it. Always keep a rag nearby to dry up spillage of water when removing the pump. 7. Remove any objects from the pump impeller by rotating it. 8. Put the cap back on the emergency emptying hose and place the latter back in its seat. 9. Screw the pump fully in. 10. Close the pump door.
Care and cleaning 25 When the appliance is in use and depending on the programme selected there can be hot water in the pump. Never remove the pump cover during a wash cycle, always wait until the appliance has finished the cycle, and is empty. When replacing the cover, ensure it is securely retightened so as to stop leaks and young children being able to remove it.
What to do if… 7. Screw the hose back to the machine and make sure the connection is tight. 8. Turn on the water tap. Frost precautions If the machine is installed in a place where the temperature could drop below 0°C, proceed as follows: 1. close the water tap and unscrew the water inlet hose from the tap; 2. place the end of the emergency emptying hose and that of the inlet hose in a bowl placed on the floor and let water drain out; 3.
What to do if… 27 During machine operation it is possible that the yellow pilot light of button 8 blinks, one of the following alarm codes appears on the display and at the same time some acoustic signals sound every 20 seconds to indicate that the machine is not working: : problem with the water supply • : problem with the water draining • : door open • : anti-flooding system has activated • Once the problem has been eliminated, press the button 8 to restart the programme.
What to do if… Problem Possible cause/Solution The drain hose is squashed or kinked. • Check the drain hose connection. The drain filter is clogged. • Clean the drain filter. An option or a programme that ends with the The machine does not empty and/or does not water still in the tub or a that eliminates all the spin: spinning phases has been selected. • Select the draining or the spinning programme. The laundry is not evenly distributed in the drum. • Redistribute the laundry.
What to do if… Problem 29 Possible cause/Solution The transit bolts and packing have not been removed. • Check the correct installation of the appliance. The support feet have not been adjusted • Check the correct levelling of the appliance. The laundry is not evenly distributed in the drum. • Redistribute the laundry. Maybe there is very little laundry in the drum. • Load more laundry.
Technical data If you are unable to identify or solve the problem, contact our service centre. Before telephoning, make a note of the model, serial number and purchase date of your machine: the Service Centre will require this information. Technical data Dimensions Width Height Depth Depth (Overall dimensions) 60 cm 85 cm 60 cm 63 cm Electrical connection Voltage - Overall power - Fuse Information on the electrical connection is given on the rating plate, on the inner edge of the appliance door.
Installation 31 The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on the quantity and type of laundry, on the inlet water temperature and on the ambient temperature. Installation instructions Installation Unpacking All transit bolts and packing must be removed before using the appliance. You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again. 1.
Installation 3. Unscrew the three bolts using the key supplied with the machine. 4. Slide out the relevant plastic spacers. 5. Open the porthole, take out the inlet hose from the drum and remove the polystyrene block fitted on the door seal.
Installation 33 6. Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet. 7. Connect the water inlet hose as described under the paragraph «Water inlet». Positioning and levelling Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Before placing it on small tiles, apply a rubber coating.
Installation 1. Open the porthole and extract the inlet hose. 2. Connect the hose with the angled connection to the machine. Do not place the inlet hose downwards. Angle the hose to the left or right depending on the position of your water tap. 3. Set the hose correctly by loosening the ring nut. After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks. 4. Connect the hose to a tap with a 3/4” thread. Always use the hose supplied with the appliance.
Installation 35 Water-stop device The inlet hose is provided with a water stop device, which protects against damage caused by water leaks in the hose which could develop due to natural ageing of the hose. This fault is shown by a red sector in the window «A» . Should this occur, turn the water tap off and refer to your Service Centre to replace the hose. Water drainage The end of the drain hose can be positioned in three ways: 1.
Electrical connection The drain hose may be extended to a maximum of 4 metres. An additional drain hose and joining piece is available from your local Service Centre. Electrical connection Information on the electrical connection is given on the rating plate on the inner edge of the appliance door. Check that your domestic electrical installation can take the maximum load required, also taking into account any other appliances in use. WARNING! Connect the machine to an earthed socket.
Packaging materials The materials marked with the symbol are recyclable. >PE<=polyethylene >PS<=polystyrene >PP<=polypropylene This means that they can be recycled by disposing of them properly in appropriate collection containers. Ecological hints To save water, energy and to help protect the environment, we recommend that you follow these tips: • Normally soiled laundry may be washed without prewashing in order to save detergent, water and time (the environment is protected too!).
132950410 - 00 - 402009 www.electrolux.