Product Manual

10
FIGURE 16 (Right Hand Side View)
FIGURE 14 (Left Hand Side View)
(Right Hand Side View) FIGURE 15
ENGLISH
STEP 14: (SEE FIGURE 14)
• Assembleballendofcontrolcableupthroughholein
cableendttingandpulluntilballslipsinsidecurled
edgeofttingasshown.Ifballwon'tslipunderedge
ofcurlitwillneedtobeinsertedthroughopenendof
curl.
• Assemblea1/4"x1-1/4"hexboltdownthroughthe
cableendtting,the5/8"longspacerandtheleft
handholeinthechannelassembly.Securewitha
1/4"nylocknut. Tighten.
NOTE: Makesurethecablemountbracketisalignedwith
thecableendttingasshowntopreventbindingofcable.
Attachtheotherendofthecontrolcableinalaterstep.
STEP 15: (SEE FIGURE 15)
• Toattachthebladetothechannelassembly,align
thenotchedholesinthepivotplatewiththenotched
holesintheblade.Inserta1/8"x1-1/4"cotterpin
downthroughtheholeatthebendinthebladepivot
shaft.Spreadtheendsofthepin.Fromtheleftside
insertthebladepivotshaft,bendfacingup,through
thenotchedholes.Securetheshaftwithanother1/8"
x1-1/4"cotterpinthroughtheendholeintheshaft.
Spreadtheendsofthepin.
• Removetheplasticcapandone3/8"hexnutfromthe
boltinthebladeadjustspring.Adjusttheremaining
3/8"hexnutdownapproximately1"ontothebolt
threads.Hookthespringoverthespringmountrod
asshown.Placetheboltupthroughtheholeinthe
topedgeofthebladeandreassembletheother3/8"
hexnutandtightendownagainstthetopedgeofthe
blade.Replacetheplasticcapovertheendofthebolt
threads.
STEP 16: (SEE FIGURE 16)
• Assemblethe1/2"washerontothechannelpivotpin.
• Attachthechannelassemblytothetractorbyplacing
theendofthechannelassemblyupinsidethe
pivotsupportbracketonthetractor.Alignthehole
inthepivotsupportbracketwiththesecond hole
inthechannelassembly.Insertthechannelpivot
pinthroughthealignedholesfromtheleftsideand
securewithasmallhairpincotterpushedalltheway
throughtotheloopend.
NOTE: Allhairpincottersonthissnowbladeshouldbe 
pushedthroughtotheirloopend.
1/4" x 1-1/4"
HEX BOLT (B)
CABLE END
FITTING
1/4" NYLOCK NUT (G)
5/8" SPACER (T)
CHANNEL
ASSEMBLY
HOLE
REAR
3/8" HEX NUT
(TOP)
PLASTIC
CAP
3/8" HEX NUT
(BOTTOM)
BLADE
1/8" x 1-1/4"
COTTER PIN (O)
BLADE
PIVOT
SHAFT
SPRING
MOUNT
ROD (Z)
BLADE
ADJUST
SPRING
1/8" x 1-1/4"
COTTER
PIN (O)
PIVOT PLATE
1/2" WASHER (S)
CHANNEL
PIVOT PIN (AA)
CHANNEL
ASSEMBLY
HOLE IN END OF
CHANNEL ASSEMBLY
SMALL HAIRPIN
COTTER (N)
PIVOT SUPPORT
BRACKET