Information

MX Series multi-output power supplies
MX series output comparison table
MX100T MX180T
Max. Power Total 315 watts 378 watts
Max. Power per Output
105W + 105W + 105W
or 105W + 210W
180W + 180W + 18W
or 360W + 18W
Max. Volts/Amps from
a single output
70V
6A
120V
20A
Output 1 Ranges
16V/6A, 35V/3A 15V/10A, 30V/6A, 60V/3A,
15V/20A*, 30V/12A*, 60V/6A*, 120V/3A*
Output 2 Ranges 16V/6A, 35V/3A, 35V/6A* 15V/10A, 30V/6A, 60V/3A
Output 3 Ranges 35V/3A, 70V/1.5A, 70V/3A* 5.5V/3A, 12V/1.5A
* range available subject to another output being disabled (shared power mode).
The MX Series - a new power supply generation
The MX Series represents a new generation of multiple output laboratory
power supplies from Aim-TTi.
Offering high power within a compact format they use ranged switched
mixed-mode regulation with display and control via a large backlit graphic
LCD with soft keys.
The first models in the MX Series to be launched are the 315 watt triple
output MX100T and 375 watt triple output MX180T.
Three full-performance outputs
All outputs of an MX Series power supply have fully variable voltage
and current setting and are able to operate in both constant voltage and
constant current modes.
High resolution metering is incorporated and variable OVP and OCP trips are
provided. Each output has its own DC On/Off switch.
Mixed-mode regulation
To provide its impressive power density the MX series combines high
frequency switch-mode pre-regulation with linear post-regulation to offer
performance that comes close to that of an all-linear design.
Excellent line and load regulation is matched by low noise and good
transient response.
Range switching and power control
To increase its ability to match a variety of applications, each
output has more than one range.
This enables higher currents to be provided when the voltage
requirement is lower, or higher voltages when the current
requirement is lower.
When higher power is required, a shared power mode is
available in which twice the power is available from a single
output..
MX Series Key Features
Three high performance outputs each with full functionality
Range switching gives variable voltage/current combinations
Shared power mode provides double power from a single output
Low output noise and ripple via linear final regulation
High setting resolution of up to 1mV and 0.1mA
Variable OVP and OCP trips on all outputs
50 setting memories per output plus 50 linked memories
Selectable voltage tracking (isolated tracking)
Selectable current meter averaging
Switchable remote sense capability
Graphic LCD provides simultaneous output metering
Numeric or spin-wheel control of all parameters
Individual or combined output on/off control with
programmable delay sequencing.
3U half-rack case for bench or rack mounting
GPIB, RS-232, USB and LAN (LXI) interfaces (-P models)
Duplicate power & sense terminals at rear (-P models)
















Typical Application Areas
Medium power bench-top applications requiring
multiple outputs
Situations where voltage and current requirements
may vary widely between projects
Repetitive testing applications requiring multi-output
settings memories
High density system applications requiring multiple
outputs from limited rack space
Remote control applications where bus interface
requirements may change





MX100T & MX100TP
315 watts total power
Three outputs of equal power, each capable of 35V at 3A
Range switching provides up to 70 volts and up to 6 amps
MX100TP includes full bus remote control
MX180T & MX180TP
375 watts plus of total power
Two high power outputs plus one low power output
High power outputs each capable of 30 volts at 6 amps
Range switching provides up to 120 volts or up to 20 amps
Low power output provides up to 12 volts or up to 3 amps
MX180TP includes full bus remote control










in a word “versatility”
Page 2