M10 airSOUND™ BAR USER’S GUIDE version 2.
CONTENTS Welcome 2 Product Overview 3 Getting Started 5 Advanced Setup & Use 9 Subwoofer Wireless 9 Other features 11 Maintenance 12 Troubleshooting 13 Specifications 16 Welcome Thank you for purchasing the orbitsound M10 airSOUND BAR with wireless subwoofer and Bluetooth. With proper use the orbitsound M10 delivers superb sound fidelity, engaging airSOUND, and will provide you with a fantastic listening experience.
Package contents Inside the box you will find: • • • • • • • • • M10 soundbar Wireless subwoofer Remote control Power supply + power cord (soundbar) Power cord (subwoofer) Quick start guide Safety and Warranty guide Analogue audio connection cable Digital optical (TOSLINK) connection cable Note: This User Guide is available for online download only.
The subwoofer (Back shown) Subwoofer Volume: Normal: Normal volume Max: +8dB volume Min: Minimum volume Wireless STATUS: OFF: No connection / No power / Low power state ON: Good sync / connection Flash: Bad connection The subwoofer is a wireless active loudspeaker that produces powerful Hi-Fi bass. It has been designed specially to complement the soundbar. Control panel overview The soundbar can be controlled from the control panel: 6 Optical Aux Bluetooth 1 2 1.
6. Source LED: Shows which source is currently playing 7. Status: Blue shows the soundbar is on. Red shows standby. (The light will flash when a button is pressed on the remote or on the control panel. Hint: Long press the power button to reset the soundbar. This will reset the source, volume, treble and bass memory to factory default settings. Press and hold for 3 seconds. The soundbar will confirm by flashing the power/status light 3 times.
Connect the Soundbar to your TV 1) Remove plastic covers from optical cable: IMPORTANT: Remove the protective plastic covers from a new TOSLINK (optical) cable before connecting to the optical sockets. Failure to remove these covers may result in damage and will interrupt the sound output. 2) Connect to your TV (optical) TV OPTICAL AUDIO OUT OPTICAL Spatial Soundbar with Bluetooth and Wireless Subwoofer ©2013 Orbitsound ltd.
3) Turn the soundbar ON: Optical Aux Bluetooth Press the power button. The indicator light will turn blue, and the optical indicator will light, showing the unit is playing the optical source. You can now hear the sound from your TV via the digital optical cable. Hint: Use the Volume + and - buttons to control playback volume. 4) Changing Source Optical Aux Bluetooth Pressing the source button on the control panel cycles through the inputs.
SS SS 1. Press to select Bluetooth sound source. The Bluetooth source light will show the status of the Bluetooth connection. 2. To pair a new device: Press and hold the Bluetooth pairing button for 3 seconds. The Bluetooth source light will flash quickly to show that pairing mode has started. Look on your device for ‘Orbitsound’ in the Bluetooth device list, and pair with it. When a device is paired, the soundbar Bluetooth source light will change to solid blue. 3.
Mute: Press the mute button to engage mute. This will stop all sound. The Soundbar status light will flash blue when mute is enabled. To resume play, press mute again. BASS TREB TREB BASS BASS TREB TREB Advanced Setup & Use The orbitsound M10 is easy to set up and enjoy, but even better sound may be achieved by following these guidelines. Spatial generation zones IMPORTANT: The areas marked need to be clear of obstacles in order for the spatial stereo sound field to work properly.
Subwoofer volume The subwoofer volume control on the back of the subwoofer allows you to preset the amount of bass that the system produces. Setting to ‘normal’ is the recommended balance. For quiet TV use, you can reduce the level. For louder music, you can increase the volume. Hint: The Bass control on the remote also changes the volume of the subwoofer. Hint: Once the subwoofer volume is set, you won’t need to adjust it often. It is set for the conditions of the room.
Hint: There are a total of 10 channels. Shift the channel repeatedly until there is no more interference. The soundbar will remember the channel when power is disconnected, so once set, there is no need to re-set. Subwoofer Pairing To pair a subwoofer to the soundbar, follow this procedure: POWER OPTICAL Spatial Soundbar with Bluetooth and Wireless Subwoofer ©2013 Orbitsound ltd. Model: M10 ON OFF AUX IN Approved components used WIRELESS CAUTION: To prevent electric shock, do not remove screws.
Other features Power saving The M9 features a low power state with wireless subwoofer lowpower control. When the soundbar enters standby mode, the power consumption reduces. It is recommended that Users routinely use standby mode to minimise household energy use. Setting memory When in standby mode, or if disconnected from the mains completely, the soundbar will remember settings for pairing, bass, treble, volume and source selection.
Maintenance Cleaning and care advice Use a soft, clean cloth moistened with plain, luke-warm water to clean the exterior of the unit. Glass cleaner is a good way to remove finger marks, but please use it sparingly, and avoid contact with the actual loudspeaker driver units. IMPORTANT: Never use solvents such as benzene or other strong chemical cleaners since these could damage the unit’s finish. It is VERY important that no liquid reaches the inside of the unit.
The sound is out of sync with the TV Make sure all video sources are connected to the TV and that the soundbar is connected to the TV optical output or RCA (AUX) output. This connection method should re-align the sound. If it is still out of sync, look for a sound/time alignment menu in the TV menus. Remote does not work Check that plastic strip in remote has been removed. If the remote has had a lot of use, replace the battery.
subwoofer (soundbar working) Check the subwoofer volume (back of subwoofer). Set to ‘normal’, then adjust to preference. Switch off subwoofer, wait for 1 minute, and switch on the subwoofer to reset it. Check power cables and power switches on soundbar and subwoofer. Try a different wireless channel. Use a paperclip to short press the pair button on the back of the soundbar.
Specifications Frequency range +/- 3 dB [Hz] 38 – 16KHz Control; response (remote control) LF: +,-8dB subwoofer volume HF: 10KHz +/- 8dB EQ Maximum SPL [dB] 97dBA Amp. power 280W total Crossover frequencies [Hz] 190/5,000 Tweeter drivers 1 x 1” m/c Front main drivers 4 x 2“ Orbitsound mk2 Spatial drivers 2 x 2” Orbitsound mk2 Enclosure type Sealed/orbitsound spatial Sub-Bass driver 1 x 6.
radio or television reception, which can be determined by turning off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.