Technical Specifications

Data sheets are subject to change without notice. For the latest version, please check the product page at www.tccmaterials.com
Available Size
• 1 qt. (32 oz. / 4 cups / 0.95 L) bottle (BOM #103941)
Coverage
Refer to Technical Data section.
5. INSTALLATION
Preparation
Read all directions before starting work.
• Prepare surfaces per manufacturers instructions of the
cement, concrete or masonry product being used. Proper
surface preparation is crucial to achieving a successful
application.
Note: It is the responsibility of the installer/applicator to ensure
the suitability of the product for its intended use.
Mixing
• Slowly stir Concrete / Masonry Set Accelerator before use.
Do not create bubbles or foaming by shaking the product.
• Always use clean tools and mixing containers.
• Follow packaged product manufacturer instructions for
proper water per bag ratio. Substitute Liquid Air Entraining
Admixture in place of “equal amount” of water to achieve the
suggested addition rate per ratio tables. So, if you add 4
ounces of this admixture, add 4 ounces less water to keep
the amount of “liquid per bag” ratio the same.
Application
This admixture is added to the mixing water of the concrete or
mortar to achieve a desired air entrainment of the finished
product. For air entrained concrete slabs, use a broom or float
finish and do not use a steel trowel finish.
Curing
Follow manufacturers instructions for the cement, concrete or
masonry product being used.
Clean Up
Follow manufacturers instructions for the cement, concrete or
masonry product being used.
Limitations
• Follow all industry standard safety procedures when handling,
such as gloves and eye protection.
• Do not allow unused bottle of product to freeze. Store dry at
40°F-95°F (4°C-35°C).
Safety
READ THE SAFETY DATA SHEET (SDS) BEFORE USING
THIS PRODUCT. SDS information is available on our website:
tccmaterials.com
Cautions
Read complete cautionary information printed on product
container prior to use.
This Product Data Sheet has been prepared in good faith on the
basis of information available at the time of publication. It is
intended to provide users with information about and guidelines
for the proper use and application of the covered Akona brand
product(s) under normal environmental and working conditions.
Because each project is different, TCC Materials cannot be
responsible for the consequences of variations in such
conditions, or for unforeseen conditions.
1. PRODUCT NAME
Akona
®
Liquid Air Entraining Admixture
2. MANUFACTURER
Akona Manufacturing, LLC
A TCC Materials Company
2025 Centre Pointe Blvd., Suite 300
Mendota Heights, MN 55120 USA
Phone: [phone]
Web: tccmaterials.com
3. PRODUCT DESCRIPTION
Akona Liquid Air Entraining Admixture is a ready to use
aqueous solution of special organic materials. Liquid Air
Entraining Admixture entrains a small and stable amount of air
into the desired mix. These small, stable air voids enhance the
mixture and improve workability. Its chemical composition and
physical properties make it ideal for many construction
applications. It is intended for use when increased workability
and freeze-thaw durability of concrete or mortar is preferred.
Features and Benefits
• Improves strength, workability, and freeze-thaw resistance
• Improved plasticity, water retention, and cohesiveness of
mortar
• Improved resistance to scaling from deicing salts
• Reduced permeability, increased water tightness
• Reduced segregation and bleeding
• Meets ASTM C260 Standard Specification for Air-Entraining
Admixtures for Concrete
When/Where to Use
• Exterior
• Concrete and cement mixes
• Masonry mortars
4. TECHNICAL DATA
• The concrete ratio (Table I) is designed to achieve an air
entrainment level of 6.5% (± 1.5%).
• The mortar ratio (Table II) is designed to achieve an air
entrainment level of 8% (± 2%).
• Many factors can effect final air content when mixing
concrete or mortar product in the field.
LIQUID AIR ENTRAINING
ADMIXTURE
Air entraining admixture for concrete and mortar
Table I: Concrete Air Entrainment Target 6.5% (± 1.5%)
Product: Suggested Rate:
60 lbs. (27.2 kg) Pre-blended
Concrete
3 fl. oz. (⅜ cup)
(88.7 ml)
80 lbs. (36.3 kg) Pre-blended
Concrete
4 fl. oz. (½ cup)
(118.3 ml)
94 lbs. (42.6 kg) Portland Cement
16 fl. oz. (2 cups)
(473 ml)
Table II: Mortar Air Entrainment Target 8% (± 2%)
Product: Suggested Rate:
60# Type N Pre-blended Mortar
4 fl. oz. (½ cup)
(118.3 ml)
80# Type N Pre-blended Mortar
5 fl. oz. (⅝ cup)
(147.8 ml)
80# Type S Pre-blended Mortar
6 fl. oz. (¾ cup)
(177.4 ml)