Instructions
Table Of Contents
- Titelseite
- Inhaltsverzeichnis
- Bildteil Häcksler Easy Crush MH/LH 2810
- Original-Betriebsanleitung
- Translation of the original instructions for use
- Vertaling van de originele gebruikershandleiding
- Traduction de la notice d’utilisation originale
- Traducción del manual original de instrucciones
- 1 Acerca de este manual de instrucciones
- 2 Descripción del producto
- 3 Instrucciones de seguridad
- 4 Montaje
- 5 Puesta en funcionamiento
- 6 Funcionamiento
- 7 Mantenimiento y limpieza
- 8 Almacenamiento
- 9 Eliminación del producto
- 10 Ayuda en caso de avería
- 11 Servicio de atención al cliente/servicio técnico
- 12 Garantía
- Traduzione del manuale per l'uso originale
- Prevod originalnih navodil
- Prijevod originalnih uputa za uporabu
- Tłumaczenie oryginalnej instrukcji obsługi
- Překlad originálního návodu k použití
- Preklad originálneho návodu na použitie
- Az eredeti kezelési útmutató fordítása
- Oversættelse af den originale brugsanvisning
- Översättning av originalbruksanvisning
- Oversettelse av den originale bruksanvisningen
- Käännös alkuperäisestä käyttöohjeesta
- Originalios naudojimo instrukcijos vertimas
- Oriģinālās lietošanas instrukcijas tulkojums
- Перевод оригинального руководства по эксплуатации
- Переклад оригіналу посібника з експлуатації
442981_a 27
Disposal
9 DISPOSAL
■
Electrical and electronic appliances do
not belong in household waste, but
should be collected and disposed of
separately.
10 HELP IN CASE OF MALFUNCTIONS
NOTE For malfunctions that are not listed
in this table or that you cannot resolve yourself,
please contact our customer service.
MH 2810
Malfunction Possible cause Solution
Motor does not start. Collector box missing or not
locked.
Push collector box in completely and
lock it.
Mains socket (house installation)
defective.
Use a different mains socket in the
house.
Extension lead defective. Inspect the lead and replace it, if
necessary.
Machine does not pull in
material to be shredded.
Collector box overflowing due to
material backing up in the cutting
unit.
Empty collector box.
Remove material to be shredded
from the cutting unit, if necessary,
see see chapter 6.5 "Clearing a cut-
ting disk/cutting drum blockage",
page25.
Cutting unit clogged with wet mate-
rial to be shredded.
Clear the clogging by feeding branch
material.
Material to be shredded
is not properly cut.
Blades blunt or damaged Turn or replace the blades, see see
chapter 7.2 "Replacing/turning the
shredder blades (MH 2810) (11/12)",
page26
Motor switches off. Motor protection switch switched
off due to cutting disk overload or
blockage.
The motor can be switched on again
after a cool-down phase of approx.
fiveminutes.
Unusual noises, rattling
in the machine.
Bolts on the motor, its mounting,
the carriage or the cutting unit are
loose.
Re-tighten bolts.
LH 2810
Malfunction Possible cause Solution
Motor does not start. Direction of rotation switch in zero
position.
Turn the direction of rotation switch
to the left or right.
Collector box missing or not
locked.
Push collector box in completely and
lock it.
Mains socket (house installation)
defective.
Use a different mains socket in the
house.
Extension lead defective. Inspect the lead and replace it, if
necessary.