SAVE THESE IMPORTANT SAFETY INSTRUCTIONS! 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. 5.
• If the product has been dropped or the housing has been damaged; • If the product exhibits a distinct change in performance. 10. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 11. Do not use the telephone to report a gas leak in the vicinity of the leak.
C s ntts en ntte on Co N Noottee:: When using hyperlinks to navigate through this document, you may use either the "back" button of your reader software to return to the table of contents, or the bookmark, using the bookmark display button.
MODEM CONNECTIONS Connector Pinout Power Supply Visual Indicators Subscriber Line Interface Ethernet Interface Single PC Configuration Straight-Through Cable Layout Multiple PC Configuration Crossover Cable Layout ATMF-25 Interface NETWORK CONNECTIONS Virtual Connections ATM-Forum Interface Ethernet Interface ISP/Corporate Network Requirements BRIDGED CONNECTIONS Multiprotocol Number of Machines Supported Plug and Play PC/Workstation Configuration Bridged Service with Filtering POINT TO POINT TUNNELING CONN
LAN Protocols Supported Known Limitations ADVANCED CONFIGURATIONS Overview IP Parameters Sample Configurations Ping-of-Life Procedure Ping-to-Defaults Procedure CHANGING THE MODEM SETTINGS Configuring the Browser Accessing the ADSL Modem Interface Welcome Page Basic Configuration Advanced Configuration Bridge Configuration Basic PPP/PPTP Configuration Advanced PPP/PPTP Configuration System Overview Page REGULATORY INFORMATION Environmental Conditions Safety Standards Power Supply Conformance Declarations In
SECTION 1: QUICK START PROCEDURES This section of the 1000 ADSL High Speed Modem User’s Guide provides the basic instructions to install your modem and access online services as quickly as possible. Procedures include steps for correct placement of your modem, cable connections, and switching on the modem. These quick start procedures assume a single PC configuration using the modem's default settings. A detailed description of features is provided in section 2 of this user's guide.
W Wa allll--M Mo ou un nttiin ng gO Op pttiio on n Part of the packaging is a wall-mounting template. If you want to mount the modem on a wall, cut the template out and use it as follows (see figure 1). 1. Use template to mark positions of holes as indicated in table A. Table A. If you mount the modem on... Mark positions of holes Left side of corner A1 and A2 Right side of corner B1 and B2 Area of wall away from corner Either A1 and A2 or B1 and B2 2. Drill the marked holes with a 6-mm (0.24-in.
Template Corner Figure 1. Wall-Mounting Instructions F Fiilltte err IIn nsstta alllla attiio on n To maintain normal phone service, a special filter must be installed in the Network Interface Device or NID, the gray box mounted on the outside of your home that terminates your phone connection. This filter, sometimes called a splitter, splits the voice (phone) signal from the ADSL (data) signal. Set-up and installation charges for ADSL service typically include the filter installation.
D De ette errm miin niin ng gY Yo ou urr S Se errvviic ce eT Tyyp pe e N Noottee:: Before continuing, you must know the type of service you are being provided. If you do not know your service type, contact your service provider for this information. Your service type is one of the following: • Bridged Service (RFC 1483) [with or without filtering] • Point To Point Service (PPP) • ATM-25 Service (ATMF) The ADSL modem is available in various models.
S Syysstte em mR Re eq qu uiirre em me en nttss The Alcatel 1000 ADSL high speed modem requires a PC or workstation equipped with an Ethernet 10Base-T network adapter card. N Noottee:: Before you begin, you will need to ask your service provider whether your connection will use static addressing, or DHCP (dynamic) addressing. You will need this information at step 9. H Ha arrd dw wa arre e IIn nsstta alllla attiio on n To connect your high speed ADSL modem, follow these steps: 1.
13. When the TCP/IP Properties window appears, click the IP Address tab. 14. If your service is DHCP, click the Obtain an IP address automatically radio button. If your service uses static addressing, press the Enter IP address radio button, and enter the IP address and subnet mask assigned to you by your service provider. 15. Restart your computer. 16. Turn on the modem by switching the on/off switch to |. Power/Sync Light The Power/Sync light begins blinking.
P PO OIIN NT TT TO OP PO OIIN NT TS SE ER RV VIIC CE E If your service provider is providing point to point (PPP) service, your ADSL modem should have model number 3EC 18202 BB or 3EC 18202 DB on the bottom of the modem case. S Syysstte em mR Re eq qu uiirre em me en nttss The Alcatel 1000 ADSL high speed modem requires a PC or workstation equipped with the following: 1. Ethernet 10Base-T network adapter card, 2. Operating system such as Windows 95, Windows 98, or Windows NT (see note) 3.
6. Connect one end of the Alcatel Data Cable (provided) to the modem connector labeled 10BASE-T. 7. Connect the other end of the Alcatel Data Cable to the Ethernet 10Base-T network adapter card in your PC. 8. Start your PC. 9. Click Start, Settings, Control Panel, and finally, the Network icon. 10. Click the Configuration tab. 11. Scroll down to the TCP/IP protocol adapters, find the adapter which includes the name of your Ethernet card, and select it. 12. Click the Properties button. 13.
W Wiin nd do ow wss 9 95 5//W Wiin nd do ow wss 9 98 8D Diia all--U Up pP Prro oc ce ed du urre ess The dial-up feature is not included in the Windows 95 operating system. It can be downloaded without cost from the Microsoft web site http://www.microsoft.com or obtained through other software distribution sources. Procedures for downloading and installing this software are provided next. Downloading Dial-Up Networking Software Upgrade (Windows 95 Only) To download the Windows Dial-Up Networking 1.
N Noottee:: If you installed Windows 95 from a CD, have the Windows 95 CD ready before you begin the installation. To install the MSDUN13.exe file, proceed as follows: 1. At your desktop, click Start, and select Run from the menu. The Run window appears. 2. Specify the path for the MSDUN13.exe file in the Open box and click OK. This will install Microsoft Dial-Up Networking 1.3 for Windows 95. Do you wish to continue? 3. Click Yes. The End-User License Agreement window appears.
N Noottee:: If you do not see the VPN adapter on the list, it means that the operating system component file for this adapter was not loaded when Windows 98 was installed on your PC. You will need your Windows 98 CD-ROM at this point. The procedure follows: 5. Select Start, Settings, click Control Panel. 6. Double-click the Add/Remove Programs icon. The Add/Remove Programs Properties window (shown below) opens. 7. Click the Windows Setup tab.
12. Your PC will prompt you to insert your Windows 98 CD. When you do this, VPN will install, and you can follow the steps under Installing Dial-Up Networking Software (Windows 98 Only) to activate VPN. Configure the Connection To configure a new PPP connection to your corporate network or an ISP, do the following: 1. Double-click the My Computer icon. 2. Double-click the Dial-Up Networking icon. 3. Activate the Make New Connection application by double-clicking on the corresponding icon.
Figure 3. VPN Server Field (Windows 98 example) 8. Enter 10.0.0.138 (default IP address of the ADSL modem). 9. Click Next. A window appears indicating you have successfully installed a new dial-up networking Connection. 10. Click Finish. A new icon with the name of the connection you just created is added to your Dial-Up Networking folder (see figure 4). You can use this icon to make a connection to your corporate network or ISP.
Figure 4. Dial-Up Networking Folder (Windows 95 Example) Make the Connection After configuring the PPP connection, make the connection: 1. Double-click the My Computer icon. 2. Double-click the Dial-Up Networking icon. 3. Activate the connection setup by double-clicking the icon of the connection you want to establish. The Connect To window appears (see figure 5).
Figure 5. Connect To (Windows 98 Example) 4. Enter the User name and Password (the IP address defaults to the modem's IP address of 10.0.0.138). 5. Click Connect. The Connecting To window appears (see figure 6). Figure 6. Connecting To (Windows 95 Example) This window indicates the status of the connection process. When the connection is established, a connection icon appears on your desktop. You are now connected to the destination specified in the connection icon.
If you intend to use this connection often, it may be useful to create a shortcut to it on your desktop. To create a shortcut, select the icon and drag it to your desktop. The program asks if you want to create a shortcut to the selected item. Select Yes and a copy of the selected icon appears on your desktop. You can now make a PPP connection by double-clicking the shortcut. Break the Connection To break the connection, proceed as follows: 1. Click the connection icon. 2. Click Disconnect.
Figure 7. Network Window 4. Select the Protocols tab and click Add. The Select Network Protocol Window appears (see figure 8).
Figure 8. Select Network Protocol Window 5. Scroll the dialog box and select Point-to-Point Tunneling Protocol from the list. 6. Click OK. The system prompts for a directory to copy installation files. 7. Specify the directory and click Continue. The installer loads the PPTP files. The PPTP Configuration window appears (see figure 9). Figure 9. PPTP Configuration Window 8.
10. Click OK to continue. This initiates configuration of the RAS. N Noottee:: You have completed the first part of the installation by adding PPTP as a remote protocol. The remaining steps configure RAS for PPTP. 11. In the Remote Access Setup Window (figure 11), add the new VPN ports to RAS by clicking Add. The Add RAS Device window appears (see figure 12). Figure 11. Remote Access Setup Window Figure 12. Add RAS Device Window 12. Each RAS Capable Device (also called a port) must be added individually.
Figure 13. Configure Port Usage Window 15. Select the Dial-out only option and click OK. 16. Perform steps 14 and 15 for each port (if required), then proceed with step 17. 17. To define which tunneled protocols you will allow through the VPNs, highlight each port and click Network. Then, in the Network Configuration Window, enable or disable the protocols you want and click OK. N Noottee:: You can enable or disable IP, IPX, or NetBEUI sessions for each port. 18. Click Continue. 19. Click Close.
To configure a connection to your corporate network or ISP, do the following: 1. Double-click the My Computer icon. 2. Double-click the Dial-Up Networking icon. 3. Is this the first time you are creating a connection? • If yes, go to step 4. • If no, go to step 5. 4. The Dial-Up Networking Window indicates that the phonebook is empty and prompts you to add an entry. Click OK and go to step 6. 5. The Dial-Up Networking window appears (figure 14).
N Noottee:: You can assign more than one phone number to each entry. This might be useful if you have a pool of phone numbers to connect to. To do this, click Alternate. 9. Select the serial line protocol offered by the server you are calling and click Next. The Login Script window appears. 10. Select Automate with this script and click Next. The IP Address window appears. 11. Enter 10.0.0.138, which is the default IP address of the ADSL modem, and click Next. The Name Server Addresses window appears. 12.
N Noottee:: User name and password are unique for a specific remote destination. They must be entered each time you want to set up a connection. Therefore, it is useful to create multiple icons, one to each remote destination. If you intend to use this connection often, it may be useful to create a shortcut to it on your desktop. To create a shortcut, select the Dial-Up Networking icon and drag it to your desktop. The program asks if you want to create a shortcut to the selected item.
A AT TM M--2 25 5S SE ER RV VIIC CE E If your service provider is providing ATM-25 Service, your ADSL modem should have model number 3EC 18200 AB on the bottom of the modem case. S Syysstte em mR Re eq qu uiirre em me en nttss The Alcatel 1000 ADSL high speed modem requires a PC or workstation equipped with an ATMF 25.6 Mb/s network adapter card that supports encapsulations and protocols described in RFC 1483 and RFC 2364.
Power/Sync Light The Power/Sync light begins blinking. After about two minutes, the light should be solid green. If the light is not solid green, check the telephone line cable between the modem LINE connector and the phone jack. If this connection is secure and the Power/Sync light is not solid green, contact your service provider for assistance. ATMF-25 Light The ATMF-25 light should be solid green.
SECTION 2: DESCRIPTION OF FEATURES The Alcatel 1000 ADSL high speed modem provides high speed virtual connections to multiple services simultaneously, using ATM/ADSL on standard telephone twisted pairs. Asymmetric Digital Subscriber Line (ADSL) is a high speed transmission technology that takes advantage of existing copper telephone lines and new telephone technologies to deliver data services to residential and small business users located within a limited distance from the Central Office (CO) exchange.
ADSL Modem Remote Splitter Small Office User ATM Network Ethernet/ ATMF Residential User Access Server Internet Access Server Information Servers Internet ISP Information Servers Corporate LAN Figure 15.
• Power Switch - On/Off switch Figure 16. Connectors on ADSL Modem N Noottee:: The modem has either an ATMF-25 connector or a 10BASE-T/MDI-X connector, not both. C utt ou no Piin orr P ctto ec ne nn on Co See figure 17 and table C for details on the modem connectors. 123456 12345678 RJ 14 RJ 45 Front view Front view Line ATMF-25 12345678 RJ 45 Front view 10BASE-T MDI-X Figure 17.
Table C. Connector Pinout Connector Pin No.
continuously green, the ADSL modem is ready for operation with terminal equipment. V Viissu ua all IIn nd diic ca atto orrss The functions for the visual indicators on top of the ADSL modem (figure 18) are listed in table D. Figure 18. Visual Indicators Table D.
S Su ub bssc crriib be err L Liin ne e IIn ntte errffa ac ce e The ADSL access network provides two types of traffic over a single metallic twisted-pair: • Data encapsulated in Asynchronous Transfer Mode (ATM) cells. • Voice connections (regular telephone service). These two traffic types are combined on the single twisted-pair by means of the Frequency Division Multiplexing (FDM) technique. To maintain your normal phone service, a remote splitter must be installed first (see figure 19).
S Siin ng glle eP PC CC Co on nffiig gu urra attiio on n A single PC with integrated Ethernet port or Ethernet Personal Computer Network Interface Card (PC-NIC) can be connected to the ADSL modem (see figure 20). The connection must be made with a straight-through cable (see figure 21) since a PC is equipped with an Ethernet interface of type Medium Dependent Interface (MDI). ADSL Modem PC with PC-NIC Remote Splitter ATM Network Ethernet Figure 20.
N Noottee:: If the port of the hub connected to the ADSL modem is equipped with an MDI/MDI-X switch and the active position is MDI, a straightthrough cable must be used. ATM Network Remote Splitter ADSL Modem Ethernet Hub Figure 22. Multiple PC Configuration N Noottee:: The maximum length of any 10Base-T segment must not exceed 100 meters (328 feet).
C Crro osssso ovve err C Ca ab blle eL La ayyo ou utt ADSL Modem Hub 1 Receive 1 Receive Twisted-Pairs 2 2 3 3 6 6 Transmit Transmit MDI-X Port MDI-X Port Figure 23. MDI-X to MDI-X External Crossover A e ce ac errffa ntte 5 IIn 25 F--2 MF TM AT The ATMF port, available on some ADSL models, is an ATMF-25 interface.
N NE ET TW WO OR RK KC CO ON NN NE EC CT TIIO ON NS S The Alcatel 1000 ADSL high speed modem supports two methods for accessing remote sites like corporate networks or the World Wide Web via a local ISP. The two methods are direct networking and dial-up networking. Direct networking describes a connection that is always active. In other words, no preliminary steps are required to obtain a connection.
ATM devices in the network. An end-to-end connection is established by linking the virtual connections between devices. This requires all intermediate ATM devices to have VPI/VCI assignments. For the ATM network, these assignments are the responsibility of network operators. These operators configure ATM devices to provide a Permanent Virtual Connection (PVC) through the network. The PVC provides an always-on service.
Table F. Ethernet Parameters Connection VPI VCIs Encaps ulation Bridged 8 35, 43, 51, 59 RFC 1483 [1] PPP/PPTP 8 67, 75, 83, 91, 99, RFC 107, 115, 123 2364 [2] [1] Ethernet V2.0/IEEE 802.3 bridged PDUs for both LLC/SNAP and VCMUX methods [2] PPP PDUs for both LLC/NLPID and VCMUX methods Standard Ethernet protocol is used to transport Ethernet frames between the ADSL modem and the PC. The modem provides an IEEE 801.
The VPI/VCI values for Ethernet/bridging are listed in table G. Table G. Ethernet VPI/VCI Values Parameter Value Meaning VPI 8 Virtual Path Identifier VCI 35, 43, 51, 59 Virtual Channel Identifier Other parameters for the Ethernet/bridging functionality are listed in table H. Table H.
could connect about 50 systems per port to completely fill up the database (the upstream bandwidth is limited to 1 Mb/s). If only one virtual port is in use, the 256 entries can be divided over two ports (virtual, Ethernet port). P Pllu ug ga an nd dP Plla ayy The ADSL modem is a plug and play device; through the bridge learning mechanism, it discovers at which side of the bridge workstations are located. It prevents traffic submitted to the local printer from crossing the bridge.
Each time the PC starts up, it automatically broadcasts an IP address request. When the remote entity responds to this request, you are connected. The following instructions to enable DHCP assume a Windows 95 operating system: 1. Start the PC and double-click the My Computer icon. 2. Open the Control Panel and double-click the Network icon. 3. In the Network window, select the Configuration tab. 4. Select TCP/IP Protocol - 3COM EtherLinkIII ISA. 5. Click Properties. 6.
discarded. Also, all multicast frames arriving on the remote virtual port(s) are silently discarded. Broadcast Traffic on Bridge Por ts The modem forwards only IP and ARP broadcast frames in both upstream and downstream directions. IP and ARP broadcast frames arriving on the Ethernet port are forwarded to the remote virtual port(s). All other broadcast frames arriving on the Ethernet port are silently discarded.
P PO OIIN NT TT TO OP PO OIIN NT TT TU UN NN NE EL LIIN NG GC CO ON NN NE EC CT TIIO ON NS S IIn nttrro od du uc cttiio on n If local workstations require connections to the outside world via the modem’s Ethernet interface and your ISP or corporate network administrator requires that you use a dial-up connection, you must use Point-to-Point Tunneling Protocol (PPTP). This protocol enables Point-to-Point Protocol (PPP) over an Ethernet interface.
Because PPTP tunneling is based on the IP protocol, an IP connection between your local PCs and the modem must exist before setting up a local tunnel. Configuration of IP functions in the modem is described in the CHANGING THE MODEM SETTINGS section (click on that section's heading to return here.) N Noottee:: Various platforms support PPTP. Subsequent examples are provided for Windows 95, Windows 98, and Windows NT. Other operating systems are not covered.
Figure 27. All ATM Channels to a Single Remote Destination Specific Connection It is possible to connect to more than one remote site through the ADSL modem, for example, your ISP and your corporate network. In this case, the modem's ATM channels are allocated to each site. For example, four ATM channels could be provisioned to the ISP and four channels to the corporate network. The best practice is to specify the site you want to connect to.
You can specify the ATM connection to use by inserting C:n in the VPN Server field of the Connect To window (see figure 29). C refers to Connection and n is a virtual ATM channel in the range 0 to 7. Figure 29. Specifying a Connection in the VPN Server Field Custom Connection You can customize the selection of remote destinations by entering a name for a Channel ID in the PPTP Destination Table (see figure 30). Figure 30.
Figure 31. Specifying a Name in the VPN Server Field N Nu um mb be err o off P PP PP P//P PP PT TP PC Co on nn ne ec cttiio on nss S Su up pp po orrtte ed d Tunneling does not affect the local network; you may add as many workstations as the local network supports. However there is an upper limit to the number of simultaneous outbound connections. Unlike bridging, a PPP/ATM channel cannot be shared by multiple users. Every local user establishing a tunnel requires an ATM channel on the network.
One Tunnel Windows 95 and Windows 98 allow you to create only one tunnel at a time. This means that you cannot connect to an ISP and the corporate network simultaneously. Tunneling within a Tunnel Tunneling within a tunnel is not possible with Windows 95 because of its single tunnel limitation. N Noottee:: Windows NT does not share these two limitations. It is possible to create multiple tunnels and simultaneously connect to multiple remote destinations.
• The modem is preconfigured with IP address 10.0.0.138 • The default IP address can be changed to a different address • The modem can be automatically configured via BOOTP • The modem supports logical multi-homing N Noottee:: Local configuration is only possible through the Ethernet interface of the modem. IIP PP Pa arra am me ette errss The IP address used for local connection is limited to the private local network.
Table I. Default Netmask IP Address Class Default Netmask A 255.0.0.0 B 255.255.0.0 C 255.255.255.0 S Sa am mp plle eC Co on nffiig gu urra attiio on nss Single PC The modem comes preconfigured with IP address 10.0.0.138. To establish a local connection between the PC and the modem, configure the IP address of the PC within the same IP network of the modem, and if subnetting is applied, within the same IP subnet of the modem. The address must be unique within the network.
Table J. Address Allocation for Private Networks IP Address Range Allocation 10.0.0.0 to 10.255.255.255 1 class A network number 172.16.0.0 to 172.31.255.255 16 contiguous class B network numbers 192.168.0.0 to 192.168.255.255 256 contiguous class C network numbers Small Workgroup To set up a local workgroup around the modem, you can use the private IP address range of the modem. Allocate IP addresses to each PC and make sure all addresses are unique (figure 33). IP address : 172.16.0.
Automatic IP Parameter Distribution The modem can also operate in more advanced local networks that rely on a BOOTP server for centralized IP configuration. The modem contains a BOOTP client that issues BOOTP requests during the first two minutes after power-up/reset. If a BOOTP server is present in the local network, it replies, and the modem acquires its IP parameters automatically.
1. Select Start from the Windows 95 taskbar. 2. Select Programs. 3. Select MS-DOS prompt. 4. In the DOS window, execute the following command: route add For example: route add 10.0.0.140 172.16.0.0.1 To verify the IP connection, you can ping the modem. If the modem responds, you can set up tunnels.
For example: arp -a -N 138.203.5.172 Example of response: Interface: 138.203.5.172 on Interface 2 Internet Address Physical Address Type 138.203.4.76 08-00-20-83-b7-26 dynamic 5. Add a static entry to the ARP table: arp -s 01-90-D0-80-01-01 -N N Noottee:: The is a placeholder for the IP address to be assigned. In the following example, 10.0.0.145 will be used.
N Noottee:: You may also leave the entry in the ARP cache; it does not affect modem operation. N Noottee:: The modem and the PC must be in the same IP (sub)network. Otherwise, the ping is issued with the MAC address of the default router. P Piin ng g--tto o--D De effa au ullttss P Prro oc ce ed du urre e If the modem configuration is incorrect, the Ping-to-Defaults procedure can be used to restore default settings.
C CH HA AN NG GIIN NG GT TH HE EM MO OD DE EM MS SE ET TT TIIN NG GS S This section describes how to access the high speed modem to configure operating parameters. The Alcatel 1000 high speed modem is already configured with default parameters and may not require adjustment. C Co on nffiig gu urriin ng g tth he eB Brro ow wsse err Web browsers can be configured to connect to the Internet directly or via a Proxy Server. To find out if you are using a proxy server, check the preferences of your browser.
N Noottee:: The modem’s default IP address is 10.0.0.138. The welcome page appears. The modem now operates as a web server, displaying additional pages when you click on their links. Each page provides fields for entering operating parameters for your configuration. Appearing on most of the pages are the following buttons: Apply Clicking this button activates the settings you have entered. Because the settings are stored in volatile memory, they will be lost if you turn off the modem or if the modem resets.
W We ellc co om me eP Pa ag ge e The welcome page provides the following buttons: Initial Setup Click this button to access the basic configuration page for adapting internal modem settings to your local networking requirements. Bridge Click this button to configure parameters for Ethernet LAN bridging. PPP/PPTP Click this button to configure parameters for Point-to-Point Protocol (PPP) relaying. Point-to-Point Tunneling Protocol (PPTP) is used to implement PPP through the modem Ethernet port.
Because the Alcatel 1000 ADSL modem supports multihoming (one interface supporting multiple IP addresses), the manually configured IP address and the automatically acquired IP address are active simultaneously. The MAC address of the modem’s Ethernet interface is displayed under the header of the basic configuration page. The following parameters are available on this page: User Defined Configuration Table An example of the User Defined Configuration Table is shown in figure 35.
Default Gateway If you want to use the modem in a more advanced local network, you can supply the IP address of your local default gateway. For standard applications with the modem connected to multiple PCs or workstations through a multiport hub, leave this field empty. BOOTP/DHCP Configuration Table The BOOTP configuration is enabled by default. If your network has an active BOOTP/DHCP server, the modem obtains its IP parameters automatically during the first 120 seconds after being switched on.
The modem can operate with multiple IP addresses (multi-homing), but there can be only one active default gateway. If BOOTP/DHCP is enabled, the default gateway supplied in the User Defined Configuration Table is automatically disabled. Even if no default gateway is supplied by the BOOTP/DHCP server, the default gateway entry in User Defined Configuration Table is not used.
• Automatic - parameters acquired automatically through BOOTP/DHCP Configuration Table • Additional - parameters added via IP Address Table Action This field allows you to delete or add a parameter set. IP Route Table The modem can be configured to reach workstations in networks outside of its own local network. This is done by adding specific routes in the IP Route Table (figure 38). Destination Gateway Mask Intf Action - Add Use input fields below to add entry Figure 38.
Bridge Port Encap FCS VPI VCI State Action - Add Use input fields below to add entry - LLCSNAP NO 8 Figure 39. Port States Table The fields of the Port States Table are described next. Bridge Por t One of the characteristics of a databridge is the number of ports it supports. A bridge port is the logical equivalent of an interface. By default, the ADSL modem supports one local port (Ethernet interface) and four remote ports.
State This field allows you to change the state of the individual remote ports. By default, only two ports (one local port and one virtual port) are in the forwarding state, meaning traffic can pass through them. The other ports can be enabled, if required, by placing them in the Enabled state. Action This field provides action buttons to add or delete bridge ports. The maximum number of remote bridge ports is four.
B Ba assiic cP PP PP P//P PP PT TP PC Co on nffiig gu urra attiio on n The PPTP configuration page provides a PPTP Destination Table for PPP/PPTP connection information (see example in figure 41). Channel ID Name State 0 ISP1 IDLE 1 ISP1 IDLE 2 ISP1 IDLE 3 ISP1 IDLE 4 ISP2 IDLE 5 ISP2 IDLE 6 ISP2 IDLE Figure 41. PPTP Destination Table The fields of this table are described next. Channel ID The numbers displayed in this column are the ATM Virtual Channels on the ADSL line.
A Ad dvva an nc ce ed dP PP PP P//P PP PT TP PC Co on nffiig gu urra attiio on n This page contains the PPTP Connection table. It provides a more detailed listing of PPP/PPTP connections and configuration information (figure 42).
HDLC Framing PPP packets arriving via a PPTP tunnel and PPP packets encapsulated on ATM connections differ in format. The PPP format on AAL5 is shown in figure 43. P_ID Information Padding Figure 43. PPP ATM Format The PPP format within a tunnel is shown in figure 44. This format has two additional bytes (FF and 03) in front of the packet, inherited from another encapsulation method (PPP in HDLC-like framing). Address FF Control P_ID Information Padding 03 Figure 44.
R RE EG GU UL LA AT TO OR RY Y IIN NF FO OR RM MA AT TIIO ON N E En nvviirro on nm me en ntta all C Co on nd diittiio on nss • The equipment may not be mounted at a location exposed to solar and/or heat radiation. • The equipment must be mounted in normal living or working areas with a minimum ambient temperature of -5°C (23°F) in steady state conditions. • The equipment may not be subjected to water (even from other sources than rain and icing) and no condensation is allowed.
C Co on nffo orrm ma an nc ce eD De ec clla arra attiio on nss IIn ntte errffe erre en nc ce e IIn nffo orrm ma attiio on nP Pa arrtt 1 15 5o off F FC CC CR Ru ulle ess Your Alcatel product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
If your Alcatel product causes interference to radio or television reception when it is in use, you might correct the interference with any one or all of these measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Modifications to this product not expressly approved by Alcatel could void the user’s authority to operate the equipment.
P Po ou urr lle ess U Uttiilliissa atte eu urrss C Ca an na ad diie en nss d de eM Mo od de em m AVIS: L’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme à certaines normes de protection, d’exploitation et de sécurité des réseaux de télécommunications. Toutefois, le Ministère n’assure pas que le matériel fonctionnera a la satisfaction de l’utilisateur.
T TR RO OU UB BL LE ES SH HO OO OT TIIN NG GT TIIP PS S Problem Solution ADSL modem does not work (visual indicators do not light) Verify that the ADSL modem is plugged into an electrical outlet. Verify that the power switch on the ADSL modem is turned on. ATMF connection does not work Verify that the cable is securely connected to the ATMF-25 connector.
EAlcatel 1999 - All Rights Reserved 3EC 16389 ABAA TCZZA Edition 01
