Sliding Gate Operator User’s Manual Model: AC2000 www.AlekoGates.
AC2000 SLIDING GATE OPERATOR OUTLINE 1. Important safety information …………………3 2. Main features …………………………………3 3. Technical parameters …………………………4 4. Packing list ……………………………………4 5. Installation ……………………………………5 6. Electrical ………………………………………8 7. Tuning and operation ………………………11 8. Check …………………………………………15 9. Maintenance …………………………………15 10.
AC2000 SLIDING GATE OPERATOR 1. Important safety information Carefully read and follow all safety precaution and warnings before attempting to install and use this operator, incorrect installation can lead to severe injury. z Installing the AC2000 gate operator requires installation of standard 110V electrical wiring. This work should only be performed by a trained technician. Miswiring could cause personal injury or DEATH.
AC2000 SLIDING GATE OPERATOR 3. Technical parameters Table 1 Power supply AC110, 60Hz Output torque (Max.) 15N·m Motor speed 1650rpm Reduction ratio 1:30 Limit switch Magnetic limit switch Auto close time 0~44 sec. Remote control mode Single Button Environmental temperature -10ºC to +55ºC Emergency release key in case of power failure 4. Packing list After receiving the product, you should make an unpack-inspection, in which you should check whether the product was damaged.
AC2000 SLIDING GATE OPERATOR 5. Installation The AC2000 Chain-driven Gate Operator operates by forcing a straight piece of chain. This length of chain is extended between two chain brackets located at opposite ends of the gate. The entire configuration is shown in the diagram below. Fig.1 Conduit In order to protect the wires, conduit must be preset into the concrete when it is poured.
AC2000 SLIDING GATE OPERATOR Gate operator Socket head cap screw Chain box Operator bracket Nut Anchor bolt Anchor Conduit Wire Concrete pad Fig.2 Chain Box Make sure the ends of the guide chain are out of the chain holes on both sides of the chain box. Remove the cover and insert the manual release key and turn counter-clockwise to disengage the clutch. Remove the elastic band from the shaft and line up the key on the shaft with the sprocket at the chain box.
AC2000 SLIDING GATE OPERATOR Chain Brackets Use the appropriate bolts to attach the chain bracket to the frame of the gate. If the gate is of square frame style, use the square bolts shown. Gate Square frame Plain washer (Φ6) Square bolt Spring washer (Φ6) "L" bracket Plain washer (Φ8) Nut (M6) Master link Spring washer (Φ8) Nut (M8) Chain bolt Fig.4 Top view If the gate is of round frame style, use the round bolts shown.
AC2000 SLIDING GATE OPERATOR Magnets for limit switch (see Fig.7) z Install the magnet as shown in Fig.7 below. The magnet and limit switch are used to control the position of the gate. z When the magnet is installed, release the gear clutch and push the sliding gate manually to pre-determine the position. Fix the magnet bracket to the gate and then tighten the gear clutch. The lower bracket is for open position and upper bracket is for close position.
AC2000 SLIDING GATE OPERATOR Control board scheme Fig.
AC2000 SLIDING GATE OPERATOR Wiring notes for control board 1. Fuse: 10A, Ø5x20 2. Power input: E (Earth), L (Live), N (Neutral) AC110V 3. Motor: U (com), V (Positive direction), W (Opposite direction), E (grounding) 4. Capacitor: 80uF 5. Alarm lamp: AC110V 6. Sampling transformer: 220V/12V 1W 7. Force adjustor (VR): Clockwise +, Counterclockwise – 8. Power transformer: 110V/12VX12V 9. MCU: PIC 16C57C 10. Power indicator: LED1 11. Output power supply: AC24V 12. Memory card: 93C66 13.
AC2000 SLIDING GATE OPERATOR 15. Output power supply: +12V (DC +12V), COM (CO)，DET (Loop detector), I.R. (Infrared N.C) COM COM I.R GND COM +12V +12V Infrared Terminal X8, No.15 AC24V Terminal X5,No.11 AC24V Control board Infrared Control board Infrared with AC input COM DET GND COM +12V +12V COM COM Out Loop detector Out I.R Terminal X8, No.15 Infrared with DC input COM COM COM Out Out DET Terminal X8, No.15 AC24V Terminal X5,No.
AC2000 SLIDING GATE OPERATOR z z z z z To erase all existing remote controls, press and hold ‘AN’ button about 14 sec until the beeper stops ringing. This indicates that all the remote controls have been erased completely. The remote control works in a single channel mode. It has four buttons. The function of button 1, button 2 and button 3 are the same. With each press of the remote control button which has been programmed, the gate will open, stop, close or stop cycle.
AC2000 SLIDING GATE OPERATOR canceled. z Pedestrian mode: Pedestrian mode can be used to open gate about 0.3~1.5 meters for people pass through. *Set width of pedestrian mode: Please turn on the first and the second DIP switch (See Fig.8 No.18) to ON position. Press button 4 to open the gate (see Verify open direction section), Wait until the gate travels the distance according to your requirements (the distance range is 0.3m~1.5m or wait for 3~10 sec.), it is regarded as ‘the width of pedestrian mode’.
AC2000 SLIDING GATE OPERATOR and replaced the original auto-close time of pedestrian mode that you have been set in Set auto-close function of pedestrian mode section. *Keep width of pedestrian mode, cancel auto-close function of pedestrian mode: Please turn on the first and the second DIP switch (See Fig.8 No.18) to ON position. Press button 4 to open the gate (see Verify open direction section). Wait some seconds (3~10 sec.), then press the same button/button 4 to stop the gate.
AC2000 SLIDING GATE OPERATOR z Pedestrian mode: This feature can be used to open gate about 0.3~1.5 meters for people pass through. z Safe guard (Infrared photocell): If infrared beam is broken during closing, the gate will reverse and go open immediately. This feature will not function if the gate is in fully opened and closed positions or during opening. z Open priority: The gate will return to open if press ‘OPEN’ button of external button switch during closing.
AC2000 SLIDING GATE OPERATOR 10. Trouble Shooting Table 4 Trouble Possible causes The wire connector becomes loose. terminal Solutions block Motor only runs in one direction. Check wire connector terminal block. The limit switch wire connector terminal block becomes loose. Check limit switch wire connector terminal block. Check the limit switch mode.
