Owner manual

ManualsBrandsAlera Lighting ManualsLightingAPCS CVL

Page 1/4 Rev. 07/15/13 curves / CVL-APCS TID

Curv Louvered - A+CLASS

Technical Installation Data

without notice. 701 Millennium Blvd. Greenville, SC 29607 / Tel 864.678.1000 / Website www.aleralighting.com

US Patent #8,436,542

Row Mounting

sections

BottoM View

data chaRt

Nominal

Length

Approx. Weight

A B C D

3-lamp*

4' 19 lbs. 47 ¼" 48" 192 ⅝" 48 ⅝"

8' 31 lbs. 95 ¼" 96" 384 ⅝" 96 ⅝"

single Mounting

Connection SectionCross Section

2¾"

9½"

4', 8', 12'

A B B B

Note: Suspension data is computed using the standard aircraft cable assembly. The use of rigid stems will yield dierent data. Please consult

factory for stem data. *3-Lamp includes CLC cover.

4', 8', 12'

to install a/V downlight coVeR:

» »

1. Install center lamp. 2. Place A/V cover directly over center lamp. 3. Install outer lamps.

Summary of content (4 pages)

PAGE 1
Curv Louvered - A+CLASS Technical Installation Data sections 23/4" 91/2" Cross Section Connection Section Bottom View 8' Single Mounting D A 4', 8', 12' Row Mounting C A B B B 4', 8', 12' data chart Nominal Length Approx. Weight 4' 8' A B 19 lbs. 47 ¼" 31 lbs. 95 ¼" 3-lamp* C D 48" 192 ⅝" 48 ⅝" 96" 384 ⅝" 96 ⅝" Note: Suspension data is computed using the standard aircraft cable assembly. The use of rigid stems will yield different data. Please consult factory for stem data.
PAGE 2
Curv Louvered - A+CLASS Technical Installation Data Connection Instructions: 1. Install first fixture of row with two hangers. 2. Slide inner die cast plates together. 3. Secure fixture joints with two bolts and nuts and attach hanger at opposite end. 4. Repeat steps 2 and 3 until row is complete. 3-Lamp Cross Sections Suspension Instructions: 1. Set bottom nut to desired fixture height. 3-Lamp Cross Sections 2. Adjust upper nut for a minimum of ⅜" between upper and lower nuts. 3.
PAGE 3
Curv Louvered - A+CLASS Technical Installation Data A+CLass 4 rows, no wbd 120V INPUT LIGHTING CIRCUIT POWER TO CONTROLLER CCM BATTERY TYPE BR2032 INSERT Main Power Feed GROUND NEUTRAL 277VAC 120VAC NEUTRAL LINE 120\277VAC GENERAL ROW 1 NEUTRAL A/V GENERAL ROW 2 NEUTRAL A/V GENERAL ROW 3 NEUTRAL A/V GENERAL SELECT NEUTRAL WHITE BOARD ROW 4 BACK A/V WHT BRD NEUTRAL Line voltage wiring from luminaire row(s) to Classroom Control Module (CCM) per federal, state, and local codes.
PAGE 4
Curv Louvered - A+CLASS Technical Installation Data A+CLass 4 rows, no wbd 277V INPUT LIGHTING CIRCUIT POWER TO CONTROLLER CCM BATTERY TYPE BR2032 INSERT Main Power Feed GROUND NEUTRAL 277VAC 120VAC NEUTRAL LINE 120\277VAC GENERAL ROW 1 NEUTRAL A/V GENERAL ROW 2 NEUTRAL A/V GENERAL ROW 3 NEUTRAL A/V GENERAL SELECT NEUTRAL WHITE BOARD ROW 4 BACK A/V WHT BRD NEUTRAL Line voltage wiring from luminaire row(s) to Classroom Control Module (CCM) per federal, state, and local codes.