USER GUIDE Publication AP7236
Limited One Year Warranty This product is warranted to be free from defects in materials or workmanship for period of one year from the date of purchase by the original owner. To ensure a high level of performance and reliability for which this equipment has been designed and manufactured, read this User Guide before operating.
PACKED ITEMS Check that you have received the following: ST1 STUDIO OUT 1 ST2 L L 2 TRACK 1 OUT STUDIO OUT 2 L L AUX 1 CRM L R LINE IN MIC LINE IN LINE IN 1 MIC 2 MIC LINE IN 3 MIC LINE IN 4 MIC LINE IN 5 MIC LINE IN 6 MIC LINE IN 7 MIC LINE IN 8 MIC LINE IN 9 MIC LINE IN 10 MIC LINE IN 11 MIC LINE IN 12 MIC LINE IN 13 MIC LINE IN 14 R R 2 TRACK 1 IN L L AUX 2 MIC MIC R CRM R R R LINE IN 15 AUX 3 16 ST1 L ST2 L ST3 L ST4 L ST1 R ST2 R
SAFETY INSTRUCTIONS WARNINGS - Read the following before proceeding : CAUTION ATTENTION: RISQUE DE CHOC ELECTRIQUE – NE PAS OUVRIR Read instructions: Retain these safety and operating instructions for future reference. Adhere to all warnings printed here and on the console. Follow the operating instructions printed in this User Guide. Do not remove cover: Operate the console with its covers correctly fitted.
SAFETY INSTRUCTIONS Important Mains plug wiring instructions The console is supplied with a moulded mains plug fitted to the AC mains power lead. Follow the instructions below if the mains plug has to be replaced.
CONTENTS Thank you for purchasing your Allen & Heath ZED-R16. To ensure that you get the maximum benefit from the unit please spare a few minutes familiarizing yourself with the controls and setup procedures outlined in this user guide. For further information please refer to the additional information available on our web site, or contact our technical support team. http://www.allen-heath.com http://www.allen-heath.com/zed http://www.myspace.com/thezedspace Allen & Heath Warranty ......................
PANEL DRAWINGS ZED-R16 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: CAUTION (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR. CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE FUSE WITH SAME TYPE AND RATING.
INTRODUCTION TO THE ZED-R16 A Technical Overview: The Allen & Heath ZED-R16 mixer has been carefully and lovingly designed in the beautiful county of Cornwall in the UK and is manufactured alongside a wide range of professional audio mixing consoles. Allen & Heath has a long history of making classic recording mixers such as the Sigma, Syncon, System 8, Saber and the GS3000, but for a few years have concentrated on the live sound, installation and pro DJ markets.
SPECIFICATIONS Operating Levels Inputs Mono channel (XLR) Input -6 to –60dBu for nominal (+14dBu in max) Mono channel Line Input (Jack socket) +14 to –40dBu (+34dBu maximum) Insert point (TRS Jack socket) 0dBu nominal +21dBu maximum Stereo Input (Jack sockets) 0dBu nominal (control = Off to +10dB) Stereo input (phono sockets) 0dBu nominal (control = Off to +10dB) 2 Track Input (phono sockets) 0dBu nominal +21dBu maximum Outputs Main (2 Track 1) L-R (XLR) +4dBu nominal. +27dBu maximum.
102mm (4.0”) DIMENSIONS 93mm (3.7”) 470mm (18.5”) 465mm (18.3”) 704mm (27.7”) 704mm (27.
ZED-R16 User Guide SIGNAL +48V PFL/AFL R PEAK DIGITAL RETURN POST-EQ PFL/AFL L DAC FIREWIRE BUS PHANTOM POWER SWITCH AUX 1 AUX 2 AUX 3 AUX 4 ADC MAIN MIX L MAIN MIX R ZED-R 16 BLOCK DIAGRAM DIGITAL SEND POST-EQ DIGITAL MASTER TO MIX L-R ADC DIGITAL MASTER IN DAC FIREWIRE BUS PFL DIGITAL RETURN PRE-INSERT GAIN EQ IN HPF 4 BAND PARAMETRIC EQUALISER MIC IN + - 100Hz INSERT LF LM g g f HM q g f AUDIO FADER ENABLE MIDI BYPASS FADER MAIN LR L INSERT MUTE TIP SEND PAN HF
MONO INPUT CHANNEL 1 1 2 Microphone Input Socket Standard 3-Pin XLR socket wired as Pin 1=Chassis, Pin 2=hot (+), Pin 3=Cold (-). Line Input Jack Socket Standard 1/4” (6.25mm) Jack socket for balanced or unbalanced line level signals. Wired Tip=Hot(+), Ring=cold (-), Sleeve=Chassis. IMPORTANT NOTE: The Line input signal is connected to the XLR input through attenuating resistors and coupling capacitors, in other words the two inputs are summed together at different levels.
MONO INPUT CHANNEL 7 HF 7 HF EQ The HF (High Frequency) equaliser affects the frequency response of the higher audible frequencies. The corner frequency of 12kHz is around 3dB from the maximum cut or boost of the circuit. 12k ZED-R 16 HF EQ -15 dBr 20.00 +15 1 15.00 10.00 Q 5.00 0.8 2k 1k F 6 0.00 4k -5.00 700 6k -10.00 HM 400Hz 8 18k -15.00 -20.00 20.00 Hz G -15 +15 1 8 100.00 1000.00 10000.00 30000.
MONO INPUT CHANNEL 9 HF 12k -15 LMF EQ The LMF (Low Mid Frequency) equaliser affects the lower middle of the audible frequency range. The frequency graduations on the sweep control are the centre frequencies of the EQ. As with the HMF section, the Q factor is variable from 0.8 to 6. The graph shows the Q setting in the minimum, middle and maximum positions, and the extents of the frequency range. +15 1 ZED-R 16 LMF EQ dBr 20.00 Q 15.00 0.8 2k 1k F 6 10.00 4k 700 6k 5.00 0.
MONO INPUT CHANNEL AUX1 12 Auxes 1 & 2 13 Auxes 3 & 4 PRE 12 OO +6 OO +6 AUX2 PRE AUX3 POST 13 AUX4 POST OO = +6 PAN 14 14 L MUTE 16 PFL 15 SIG L-R 5 0 Mute Switch This mutes or cuts the signal to the main L-R bus and the Auxes. A rectangular LED illuminates to show the Mute switch is pressed.
MONO INPUT CHANNEL 19 Fader 20 DIG SND Post EQ switch 21 DIG RET Pre INSert switch 22 DIG RET Post EQ switch 23 FADER=MIDI switch = PAN L R MUTE PFL 1 HI SIG 10 L-R The 60mm fader can be used as a normal channel fader where it will affect the level of signal to the main L-R bus and the postfade auxes. There is 10dB of gain at the top of the travel. The fader can also be used as a MIDI controller if the FADER=MIDI switch is pressed on that channel.
STEREO INPUT CHANNEL ST1 1 ST1 (& ST2) Phono & Jack sockets 2 ST1 (& ST2) Level 3 STEREO Channel EQ L R Standard RCA phono sockets and 1/4” jack sockets for unbalanced stereo inputs. The RCA phono sockets normally connect through the jack break contacts so giving a choice of which connector type to use. The left signal does not connect to the right if nothing is plugged into the right socket though, as with some of our other products.
STEREO INPUT CHANNEL HF 4 Auxiliaries 1 & 2 5 Stereo Balance control 12k -15 +15 LF 80Hz -15 +15 Each of these controls sends a mono signal to an auxiliary bus (a sum of the left & right inputs). The signal is sourced pre-fade which means that the level is independent of, and unaffected by the master level control The control varies the signal level to the bus from off (fully attenuated) to +6dB, with unity gain at the arrow.
STUDIO OUTPUTS & ST3 & 4 INPUTS STUDIO OUT 1 STUDIO OUT 2 9 L L R R 10 ST3 L ST4 L ST3 R ST4 R ST3 LEV -10 ST4 -5 LEV 0 -20 9 5 Studio Monitor Outputs The Studio Outputs allow a selection of signals to be sent as outputs for artists monitors. The selection switches enable the main L-R mix (post fader) and auxes 1 to 4 (post master level) to the studio outputs. If more than one switch is pressed the signals mix together.
AUX MASTERS & MAIN OUTPUTS. 2 TRACK 1 OUT L AUX 1 R AUX 2 1 2 Track 1 Output XLR connectors 2 2 Track 2 Output jack sockets 3 Insert L & R jack sockets 1 Standard 3-Pin XLR panel plug wired as Pin 1=Chassis, Pin 2=hot (+), Pin 3=Cold (-). Electronically balanced, +4dBu = 0VU.
MASTER SECTION CRM L 2 TRACK 1 IN 1 Control Room Monitor jack sockets 2 Alternate Monitor jack sockets 3 2 Track 1 Input phono sockets 4 2 Track 2 Input jack sockets 5 Main meters 6 PFL/AFL Active LED 7 2 TRACK DUB switches 8 2 TRACK 1 replace L-R switch L 1 3 CRM R Standard 1/4” (6.25mm) Jack socket for connecting powered monitor speakers or an amplifier for the engineers control room monitor speakers. Impedance balanced. Wired Tip=Hot(+), Ring=cold (-), Sleeve=Chassis.
MASTER SECTION 9 2 TRACK 1 REPLACE L-R TALK LEV MIN MAX 9 Talkback Section A built in microphone and talkback system allows the engineer to talk to the artists in the studio or foldback monitors on stage. The Talk Level control adjusts the gain of the amplifier, be wary of feedback if the talkback signal is routed to the local monitors via the AFL system or the proximity of the studio monitors is such that they are able to feedback to the talkback microphone.
DIGITAL CONNECTIONS & SWITCHES 1 2 5 4 3 MIDI OUT ADAT OUT 9-16 1-8 ADAT IN 9-16 1-8 FIREWIRE ADAT 44.1kHz 48kHz FireWire/ADAT configuration switch 1 2 This switch determines whether the digital interface is predominantly FireWire or ADAT and will be dependent on what type of external equipment is used. Set to FireWire if a computer or equipment with IEEE 1394 FireWire connection is to be used or ADAT if an ADAT machine only is to be connected.
DIGITAL INPUT & OUTPUT CONFIGURATIONS DIGITAL I/O CONFIGURATIONS: 1 FireWire mode 44.1 or 48kHz MONO CHANNELS 1 -16 ANALOGUE I/O 1-8 9-16 1-8 STEREO MASTER 9-16 17-18 17-18 FIREWIRE ADAT A-D A-D D-A D-A DAW ZED-R16 The following four set-up configuration diagrams show a schematic representation of the ZED-R16 digital I/O section connected to the recording/playback equipment. Note the FireWire channel differences at higher sample rate settings.
ZED DICE DRIVERS: SYSTEM COMPATIBILTY DRIVER RELEASE VERSION: V3.3.2 The ZED DICE drivers are supplied to Allen & Heath by TC Applied Technologies Ltd. They are customised versions of drivers used in generic FireWire devices used extensively throughout the Pro Audio industry.
CONNECTING TO A COMPUTER Downloading the Drivers Your ZED-R16 has software installed and working already, but in order for your Windows or MAC computer to be able to communicate with the FireWire device in ZED-R you’ll need to load some Drivers onto your computer. The installer software is available on the Allen & Heath website at: http://www.allen-heath.com/zed/ Microsoft Windows XP + Vista Installation: Make sure that the ZED-R16 is not connected to your computer.
CONNECTING TO A MAC Downloading the Drivers Your ZED-R16 has firmware installed and working already, but in order for your MAC computer to be able to communicate with the FireWire device in ZED-R you’ll need to load some Drivers onto your computer. The installer software is available on the Allen & Heath website at: http://www.allen-heath.com/zed/ MAC Installation: Make sure that the ZED-R16 is not connected to your computer. Save the DMG file to your MAC desktop.
ZED DICE CONTROL PANEL A description of the Control Panel for the ZED DICE driver v3.3.2. Both the Windows & Mac versions are covered by this guide, the differences are highlighted where relevant. The Windows or Mac installer program will install the driver software for the ZED DICE audio streaming device onto your computer, and a control panel application which can be used to check and set up certain parameters such as sample rate and synchronisation source.
ZED DICE CONTROL PANEL The control panel is divided into two main sections, Global Settings and Device Settings. Global Settings All system related settings are here, grouped into four Tabs for Windows, two for the Mac version. Bus Tab: Contains controls for choosing the system clock master device, sample rate, synchronisation source, buffer size, and operation mode. When the mouse pointer hovers over the Master combo box, a ToolTip will display the IEEE1394 unique ID of the device.
ZED DICE CONTROL PANEL The WDM tab (Windows only) can be used for enabling or disabling the Windows Driver Model audio channels, configuring them as mono, stereo or surround, depending on your computer’s capability, and mapping the WDM channels to the required channels on your ZED-R16. For example you can map the stereo WDM channels to the master L-R channels (17-18) on your mixer so that your computer CD player and general audio will be played to the Master L-R channels for monitoring.
ZED DICE CONTROL PANEL Device Settings This area of the control panel shows information for the ZED-R16 if connected to the FireWire bus. The device (mixer) is shown in the Devices list on the right, the clock symbol is displayed if it is the clock master and a padlock symbol shows if the device is locked or unlocked (synchronised or not). On the left of the Device Settings area are two Tabs, General and Firmware Loader.
ZED-R16 User Guide fx 33 fx ST1 STUDIO OUT 1 ST2 LINE IN KEY: MIC LINE IN 1 MIC LINE IN 2 MIC LINE IN 3 MIC LINE IN 4 MIC LINE IN 5 MIC LINE IN 6 MIC LINE IN 7 MIC LINE IN 8 MIC LINE IN 9 MIC LINE IN 10 MIC LINE IN 11 MIC LINE IN 12 MIC LINE IN 13 MIC LINE IN 14 KT-88 2 TRACK 1 OUT STUDIO OUT 2 L AUX 1 L L L L R R R R ST1 L ST2 L ST3 L ST4 L ST1 R ST2 R ST3 R ST4 R CRM L R 2 TRACK 1 IN L AUX 2 MIC MIC CRM R R LINE IN 15 AUX 3 16
ZED-R16 User Guide fx 34 fx ST1 STUDIO OUT 1 ST2 STUDIO OUT 2 L L L R R R R ST1 L ST2 L ST3 L ST4 L ST1 R ST2 R ST3 R ST4 R 2 TRACK 1 OUT R L AUX 1 L CRM L LINE IN KEY: MIC LINE IN 1 LINE IN 2 INSERT MIC LINE IN 3 INSERT MIC LINE IN 4 INSERT MIC LINE IN 5 INSERT MIC LINE IN 6 INSERT MIC LINE IN 7 INSERT MIC LINE IN 8 INSERT MIC LINE IN 9 INSERT MIC LINE IN 10 INSERT MIC LINE IN 11 INSERT MIC LINE IN 12 INSERT MIC LINE IN 13 INSERT MIC LINE
MODES OF OPERATION RECORDING PRE-EQ FROM AN ANALOGUE MIX The basic mode for ZED-R16 with all the configuration switches in the up position (not pressed). ZED-R16 can be operated as a traditional analogue mixer, using the main L-R mix as a stereo monitor mix for the multitrack recording, or as a PA mix if working live. A clean recording feed will be sent on the FireWire bus or the ADAT outputs for recording each channel, sourced from just after the pre-amp and hi-pass filter.
MODES OF OPERATION RECORDING POST-EQ FROM AN ANALOGUE MIX If the DIG SEND = POST EQ switch is pressed then the digital output from the channel will be sourced from after the equaliser. Use this mode if you want to use ZED-R16 as an analogue mixer and want to EQ the signal being recorded. ANALOGUE SIGNAL MIC LINE IN 1 INSERT 48V 0 20 30 40 GAIN 50 -14 6 60 40 HPF 100Hz HF 12k -15 +15 1 Q 0.8 2k DIGITAL SIGNAL (FIREWIRE OR ADAT) 6 4k 1k F 700 6k HM 400Hz 18k G -15 +15 1 Q 0.
MODES OF OPERATION USING DIGITAL PROCESSING PLUG-INS IN AN ANALOGUE MIX The digital channel inputs and outputs are used to send a signal to the Digital Audio Workstation of software application where processing plug-ins such as noise gates or compressors can be used, almost as if they were plugged into the insert point on the channel. ANALOGUE SIGNAL MIC Analogue signal converted to digital after the Pre-amp and sent to the FireWire Bus or ADAT output.
MODES OF OPERATION IN LINE MULTITRACK RECORDING AND MONITORING The signal for recording is send pre EQ (it can be post EQ if the DIG SND = post EQ switch is pressed) and the track can be monitored by pressing the DIG RET = post EQ configuration switch. Using this mode emulates the traditional method of monitoring from the replay head of a tape machine which is a reliable way of monitoring what is being recorded.
MODES OF OPERATION ANALOGUE MIXDOWN FROM DIGITAL SOURCE Here, the digital inputs to the channels are selected to go to the channel just before the insert point (replacing the signal from the pre-amp). This mode allows for analogue mixing from a multi-track digital source using the simply gorgeous analogue EQ on the ZED-R16. It is also a great mode to use when overdubbing tracks, using the digital inputs for monitor & foldback purposes whilst using the PRE-INSert digital send to do the overdub recording.
MODES OF OPERATION DIGITAL MIXDOWN USING FADERS AS MIDI CONTROLLERS Many people will want to stay in the digital domain once their tracks are recorded. The ZED-R16 appreciates this and allows the channel faders to be used as MIDI controllers where they can be assigned to control the level or other parameter within the Digital Audio Workstation or software application. The analogue part of the fader is bypassed at unity gain, so it is still possible to route signals to the mix bus if required.
MODES OF OPERATION EXTREME FLEXIBILITY—ANALOGUE PLUG-INS! You can even use the EQ in the ZED-R16 channel as an analogue plug-in for your Digital Audio Workstation! To do this press both the DIG RET = PRE INS to source the channel from your DAW and the DIG SND = POST EQ, so the output of the EQ goes back to the DAW. You may need to create a new track in your software application for the equalised audio, otherwise a feedback loop could easily be created between the ZED-R16 and the DAW.
cakewalk SONAR LE DIGITAL AUDIO WORKSTATION SONAR LE Overview. SONAR LE is a software application from Cakewalk and is included free of charge with your new ZED-R16 mixing console. SONAR LE is a first step into the world of sequencing and hard disk recording on the Windows platform. You’ll be able to record 8 tracks simultaneously from your ZED-R16 mixer, arrange songs, then play back 8 tracks simultaneously to your ZED-R16 mixer via the FireWire bus.
System Requirements (For SONAR LE) (For running SONAR LE on a Windows computer. The system requirements for connecting to ZED-R16 are documented separately) System Requirements Minimum Recommended Windows XP Windows XP/Vista/Vista x64 Intel® Pentium® 4 1.3 GHz, or AMD™ Athlon XP 1500+ or higher Intel® Pentium® 4 2.
Next, launch SONAR LE. Click Options/Audio and click on the Drivers tab. The Input and Output Drivers for ZED R should appear in the option boxes. If they don’t, click the Advanced tab and check that the Driver Mode is set to ASIO. The Input drivers are the audio sources to the computer. Using SONAR LE, only 8 simultaneous inputs can be used at one time and these are shown in the screenshot enabled in pairs.
To record the audio on tracks 1 & 2, click the R buttons so they light up red, then the record button (circle) on the transport controls on the top icon toolbar. (Or select larger transport controls from Views). The audio wave profile will show in the track panes. Click stop (Square) when finished. To listen to the recording, click rewind, then de-select the input echo buttons (to the right of the R buttons. Also disarm the tracks by de-selecting the R buttons.
Enabling MIDI Control with SONAR LE With SONAR LE running and ZED-R16 connected via FireWire, click Options in the main menu toolbar, then MIDI Devices. Enable ZED-R as a MIDI input device to SONAR by clicking on it as below. Click OK and return to the main Options menu and click Controllers/Surfaces where you can choose the MIDI control source for your project. If none appear then click the Add New button (yellow star) and select the controller surface type as MMC-1 and the In port as ZED-R.
ZED-R MIDI IMPLEMENTATION MIDI CONTROLLER MESSAGE TYPE DATA 1 DATA 2 MIDI CONTROLLER MESSAGE TYPE DATA 1 DATA 2 FADER CH1 CC 01 0-127 SWITCH 1 NOTE ON/OFF 01 7F/00 FADER CH2 CC 02 0-127 SWITCH 2 NOTE ON/OFF 02 7F/00 FADER CH3 CC 03 0-127 SWITCH 3 NOTE ON/OFF 03 7F/00 FADER CH4 CC 04 0-127 SWITCH 4 NOTE ON/OFF 04 7F/00 FADER CH5 CC 05 0-127 SWITCH 5 NOTE ON/OFF 05 7F/00 FADER CH6 CC 06 0-127 SWITCH 6 NOTE ON/OFF 06 7F/00 FADER CH7 CC 07 0-127 SWITCH
ZED-R MIDI IMPLEMENTATION Changing MIDI Channel The default MIDI channel is 16. To change the MIDI channel follow the following procedure: 1. 2. 3. 4. 5. 6. 7. With ZED-R16 powered off, press & hold down the PLAY button and switch on the mains power to ZED-R16. Release the PLAY button. Press & hold down the MIDI switches 1,3,5 & 7 in a combination from the table below. Press and release the PLAY button again. Release the switches 1,3,5 & 7, if any are pressed from step 3. Turn off the mains power.
WIRING NOTES PROCESSOR Insert cable wiring RETURN S INSERT T OUT T R S R SEND GROUND RETURN SEND S T R IN LINK RING TO SLEEVE TO UNBALANCE Y-Adapter Y-Adapter RCA phono jacks 2 Outputs to 1 Input adapter 1 Output to 2 Inputs RCA PHONO CABLE UNBALANCED No ! UNBALANCED INSTRUMENT CABLE UNBALANCED BALANCED TRS JACK CABLE BALANCED Sleeve=ground Sleeve=ground Ring=cold (-) Ring=cold (-) Tip=hot (+) TO INPUT Tip=hot (+) 2=hot (+) 1=ground BALANCED MIC CABLE 1=ground BALANCED
PRODUCT SUPPORT Investigate ALLEN & HEATH’s other ranges at www.allen-heath.com Large Live Sound mixers — iLive digital, ML and GL Series Small Format Live Sound mixers — ZED, MixWizards and PA Series DJ products — Xone Series Sound Management Series — iDR Series Registering your product Thank you for buying the Allen & Heath ZED-R16 mixer. We hope that you are happy with it and that you enjoy many years of faithful service with it, and record and mix some great music. Please go to www.allen-heath.
