Installation Guide

ManualsBrandsallen + roth ManualsCeiling LightsLynnpark 7-in Brushed Nickel Modern/Contemporary LED Flush Mount Light

APPROVED FOR USE

IN DAMP LOCATIONS

PH19491

Purchase Date

ATTACH YOUR RECEIPT HERE

welcoming • sophisticated • inspiring

ITEM #1448562

MODEL #CLL7BNKB

FLUSHMOUNT CEILING LIGHT

Français p. 9

Español p. 17

Questions, problems, missing parts? Before returning to your retailer, call our customer service

department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.

allen + roth

is a registered trademark

Summary of content (8 pages)

PAGE 1
welcoming • sophisticated • inspiring APPROVED FOR USE IN DAMP LOCATIONS allen + roth® is a registered trademark of LF, LLC. All Rights Reserved. ITEM #1448562 FLUSHMOUNT CEILING LIGHT MODEL #CLL7BNKB Français p. 9 Español p. 17 ATTACH YOUR RECEIPT HERE Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.
PAGE 2
TABLE OF CONTENTS Package Contents ................................................................................................................2 Hardware Contents ...........................................................................................................................2 Safety Information ................................................................................................................3 Preparation ...........................................................................
PAGE 3
SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS. DANGER • For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install or operate this product. Failure to do so could lead to electrical shock, fire or other injuries that could be hazardous or even fatal. • DO NOT connect this fixture to an electrical system that does not provide a means for equipment grounding.
PAGE 4
SAFETY INFORMATION CAUTION • TURN OFF ELECTRICITY at main fuse box (or circuit breaker box) before beginning installation by removing the fuse (or switching the circuit breaker off). • If you are not sure the lighting system has a grounding means, DO NOT attempt to install this fixture. Contact a qualified, licensed electrician for information regarding the proper grounding methods as required by the local electrical code in your area.
PAGE 5
ASSEMBLY INSTRUCTIONS 2. Remove existing fixture and disconnect all electrical wiring. 2 3. Attach mounting plate (B) to outlet box (not included) using the existing washers and outlet box screws or the machine screws (BB). NOTE: If the outlet box screws required for your outlet box are of a different size than the machine screws (BB), consult with a licensed electrician before proceeding. 3 Outlet Box Tighten machine screws (BB) completely to secure mounting plate (B) to outlet box.
PAGE 6
ASSEMBLY INSTRUCTIONS 4a. Prepare wire by stripping 1/2 in. of insulation from wire ends using wire strippers (not included). Unwrap BARE wire from BLACK and WHITE wires. Connect WHITE wire from fixture (A) to WHITE wire from outlet box using existing wire connector or wire connector (AA). Connect BLACK wire from fixture (A) to BLACK wire from outlet box using existing wire connector or wire connector (AA).
PAGE 7
ASSEMBLY INSTRUCTIONS 5. Align notches on the mounting plate (B) with tabs on fixure (A). Twist fixture (A) clockwise until fixture (A) locks into place and is secure. [NOTE: This may require some force.] 5 B A 6. Restore power and test fixture (A). 6 If light does not function, please refer to TROUBLESHOOTING on the following page. CARE AND MAINTENANCE • Shut off main power supply. Wipe fixture with soft cloth. Use window cleaner to clean glass. Do not use an abrasive cleaner on glass or fixture.
PAGE 8
TROUBLESHOOTING WARNING: Before beginning work, shut off the power supply to avoid electrical shock. PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Light does not come on initially or no longer comes on. 1. Power is OFF. 2. Faulty connection. 3. LED component is not working properly. 1. Make sure power supply is ON. 2. Check wiring and all connections. 3. Contact Customer Service. Fuse blows out or circuit breaker trips. 1. Crossed wires. 2. Power wire is grounding out. 1. Check wiring. 2.