Use and Care Guide

ManualsBrandsallen + roth ManualsOutdoorsAltadena 2-Piece Metal Frame Patio Conversation Set with Sunbrella Cushions

HOSE & REGULATOR ASSEMBLY AND REPLACEMENT

1. This ﬁre table comes equipped with a standard LP gas hose and regulator including the appliance side connection for a CGA

regulator supplied with this ﬁre table must be used. Only a hose

manufacturer can be used for replacement.

a. The CGA No 791 connection incorporates a magnetic ﬂow limiting device that acts

to limit the ﬂow of gas if a leak is detected

b. If the burner valve is open prior to the LP gas cylinder service valve being opened,

the connection will interpret this free ﬂow

c. The connection safety feature will reduce gas ﬂow from the regulator to the

appliance to a minimal level.

d. Be sure that the burner control valve is closed prior to opening the LP gas cylinder

service valve to ensure that the

mistakenly.

e. If the connection ﬂow limiting device is triggered mistakenly, close the LP gas

cylinder service valve and the burner valve,

reset, open the cylinder service valve, then open the burner valve and light the

ﬁreplace as per lighting instructions.

2. Be sure to protect the hose from any hot surfaces. Serious danger may result if the hose contacts any hot surface.

3. Regular maintenance of the hose and regulator:

a. Inspect the hose before each use of the ﬁre table. If the hose shows signs of

cracks, abrasions, cuts or damage of any

replace the hose as required before using the appliance. For assistance

or replacement of the hose, call Lowes at 1-866-439-9800. Use only

replacement parts from the

b. Inspect the seal inside the CGA No 791 service valve on the LP gas cylinder when

replacing the cylinder or at least once

damage, have the seal replaced by a certiﬁed gas dealer before operating the

appliance.

4. Do not use tools to tighten the CGA No 791 connection nut onto the LP gas cylinder service valve. Hand tighten only.

5. Be careful to not cross the threads on the connection when tightening the CGA No 791 connection on to the LP gas

6. “Leak Test” should always be performed after attaching the connection to the LP gas cylinder service valve. (See “Checking

for Leaks” section of this manual on page 12).

7. For the connection of the hose and regulator to the LP tank, refer to the “Connection” section of the LP gas cylinder section

above.

Glass Beads Warning:

1. Glass media may have sharp edges. Wear safety glasses and gloves when handling.

No 791 Cylinder Connection Device. The LP gas hose and

and regulator speciﬁed by

between the regulator and the burner valve.

of gas to be a leak.

connection ﬂow limiting device is not triggered

wait 10 seconds to allow the device to

kind, do not operate the appliance. Fix or

with repair manufacturer.

per year. If there is any indication of

cylinder service valve.

3. Pour the glass media evenly in to the burner area (with the exception of the screen-if applicable). The glass should be

1/2-1”above the burner.

2. Do not change or substitute the glass media material provided with this fire pit. If replacing, use only

replacement glass media available from your local authorized dealer/distributor.

5.Keep away from the unit for the first 20 minutes after igniting your unit for the first time,as lava rocks/pumice stones

could pop out and cause injury. Should any rocks pop out,discard them.

6.Always ensure that lava rocks/pumice stones/glass shards/glass beads are completely dry before use.

cause them to crack or pop.

4. IMPORTANT: Do not exceed a height of 1" above the burner when placing glass media. Ensure no media covers

the igniter screen. Store any excess media in a safe location.

/glass shards/glass beads

Failure to do so will

DO NOT PLACE ANY

MEDIA ON SCREEN