Installation Guide

ManualsBrandsallen + roth ManualsVanity LightsQuinn 4-Light Chrome Modern/Contemporary Vanity Light

ITEM #1362615

4-LIGHT VANITY BAR

PH19217

For Damp

Location

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-866-439-9800, 8 a.m. - 6 p.m., EST, Monday - Thursday,

8 a.m. - 5 p.m., EST, Friday.

Purchase Date

ATTACH YOUR RECEIPT HERE

welcoming • sophisticated • inspiring

allen + roth

is a registered trademark

Français p. 9

Español p. 17

MODEL #VBL19-4CH

Summary of content (8 pages)

PAGE 1
welcoming • sophisticated • inspiring For Damp Location ITEM #1362615 allen + roth® is a registered trademark of LF, LLC. All Rights Reserved. 4-LIGHT VANITY BAR MODEL #VBL19-4CH Français p. 9 Español p. 17 ATTACH YOUR RECEIPT HERE Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-439-9800, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
PAGE 2
TABLE OF CONTENTS Package Contents ............................................................................................................... 2 Hardware Contents .......................................................................................................................... 3 Safety Information ............................................................................................................... 3 Preparation ...........................................................................
PAGE 3
HARDWARE CONTENTS (shown actual size) AA BB Wire Connector Machine Screw Qty. 3 Qty. 2 SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS. DANGER • For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install or operate this product. Failure to do so could lead to fire, electrical shock or other injuries that could be hazardous or even fatal.
PAGE 4
SAFETY INFORMATION WARNING • To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this light fixture are designed to accept only one 12-gauge house wire and two lead wires from the light fixture. If your house wire is larger than 12-gauge or there is more than one house wire to connect to the corresponding fixture lead wires, consult an electrician for the proper size wire connectors to use.
PAGE 5
ASSEMBLY INSTRUCTIONS 1. Turn off circuit breakers and wall switch to the fixture supply line leads. 1 DANGER: Failure to disconnect power supply prior to installation may result in serious injury or death. 2. Remove existing fixture and disconnect all electrical wiring. 2 3. Remove mounting plate (B) from fixture (A) by removing mounting plate screws (C) from the edges of the fixture (A). 3 ON ON OFF OFF C A Save mounting plate screws (C) for later use.
PAGE 6
ASSEMBLY INSTRUCTIONS 4. Attach mounting plate (B) to outlet box (not included) using existing washers and outlet box screws or the machine screws (BB). NOTE: If the outlet box screws required for your outlet box are of a different size than the machine screws (BB), consult a licensed electrician before proceeding. Tighten machine screws (BB) to secure mounting plate (B). 4 BB CAUTION: The fixture must be mounted to an outlet box that is supported by the building structure.
PAGE 7
ASSEMBLY INSTRUCTIONS 6. Wrap electrical tape (not included) around each individual wire connector (AA) down to the wire. Push wire connectors (AA) gently back into outlet box. Carefully push excess wiring into outlet box. 6 AA AA A WARNING: Make sure no bare wire or wire strands are visible after making connections. Outlet Box AA 7. Attach fixture (A) to mounting plate (B) using the mounting plate screws (C) previously removed (Step 3, Page 5).
PAGE 8
CARE AND MAINTENANCE • Shut off main power supply. Wipe with soft cloth or use window cleaner. Do not use an abrasive cleaner. • Total wattage for this fixture is 25 watts; do NOT tamper with or attempt to repair LED component of fixture. TROUBLESHOOTING WARNING: Before beginning work, shut off the power supply to avoid electrical shock. PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Light does not come on initially or no longer comes on. 1. Power is OFF. 2. Faulty connection. 3.