User Manual Ventilated Closet Kit

ManualsBrandsallen + roth ManualsWood Closet Kits8-ft W x 6.6-ft H Antique Gray Wood Closet Kit

10 11

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS

Hardware Used

15. With a pencil, draw a level line at the desired

mounting location for long shelf (K). Using

L-brackets (KK) as a guide, mark the screw hole

locations with a pencil. Drill 3/8 in. diameter pilot holes

at least 2-1/2 in. deep at marked locations, then insert

wall anchors (RR) into the holes until they are ush

with the wall. Attach L-brackets (KK) to the wall using

M4 x 38 mm screws (UU) and to the long shelf (K)

using M4 x 14 mm wood screws (VA).

13. Using a stud nder (not included), locate the

edges of the wood studs. Find the center line of each

stud and draw a vertical reference line on the wall

over each one. Position installation template (R) at

desired location on wall.

Note: The bottom of the installation template (R)

should be no less than 31-1/2 in. from the oor.

Mark mounting holes with a pencil (not included) and

discard installation template (R). Drill 3/16 in. pilot

holes at marked locations. Then, with the beveled

edge facing up, attach the wall hanging cleats (I) with

large at washers (JJ) and M8 x 2-1/2 in. lag bolts (II).

18. Insert 22 mm metal poles (T) into 25 mm metal

poles (S). Using closed pole holders (YC) as a guide,

mark screw hole locations with a pencil. Drill 3/8 in.

diameter pilot holes at least 2-1/2 in. deep at marked

locations, then insert drywall anchors (not included)

into the holes. Attach closed pole holders (YC) with

M4 x 38 mm zinc screws (ZZ). Insert 25 mm metal

poles (S) into closed pole holders (YC), securing with

M4 x 15 mm self-tapping screws (YY).

Note: Drywall anchors are not required if installing

into a stud.

Wall Anchor

L-Bracket

M4 x 38 mm Screw

M4 x 38 mm Zinc Screw

Closed Pole Holder

M4 x 15 mm Self-tapping Screw

M4 x 14 mm Wood Screw

x 8

x 4

x 8

x 9

x 3

x 8

x 16

Lowes.com/allenandroth

Drywall Anchor

14. With the help from another person, carefully

hang the unit from mounting cleats (H) & middle

xed Shelf (G) onto wall hanging cleats (I).

Long Shelf Installation

Note: If long shelf (K) needs cut to t inside your

closet space, cut only one side of the shelf and do

not use a hacksaw. It is recommended you hire an

insured remodeler for this type of installation.

17. If you intend to install the Expandable Pole,

attach wood supports (J) on the inside of upper left

side panel (A) and/ or upper right side panel (B)

using wood screws (FF).

Note: The expandable pole should be installed to the

middle of wood support (J).

Pole Installation

Hardware Used

16. Attach long shelves (K) to left side panel (A) and

right side panel (B) with L-brackets (KK), securing

with M4 x 14 mm wood screws (VA).

M3.5 x 12 mm Wood Screw

x 12

Wooden Stud

40.6 in.

Minimum 31-1/2 in.

16 in.

Hardware Used

M8 x 2-1/2 in. Lag Bolt

Large Flat Washer

x 4