User's Manual

AT-WR4662n | High-Speed Mobility - Wireless Base Router
Safety Information
CE Declaration of Conformity (DoC)
The CE Declaration of Conformity is available at:
http://www.alliedtelesis.com/support/
.
This device complies with the essential requirements of the
R&TTE Directive 1999/5/EC. The following test methods have
been applied in order to prove presumption of conformity with
the essential requirements of the R&TTE Directive 1999/5/EC:
x EMC - EN 61000-6-3:2007
x EMC - EN 61000-6-4:2007
x EMC - EN 301 489-17 V2.1.1
x EMC - EN 50121-4:2006
x EMC - EN 50385:2002
x Radio - EN 300 328 V1.7.1
x Radio - EN 301 893 V1.5.1
x Safety - EN 60950-1:2006+A11:2009+A1:2010
This product may be used in all EU countries and other
countries following R&TTE directive 1999/5/EC.
In France, outdoor use is limited to 10 mW within the band
range of 2454÷2483.5 MHz..
Additional requirements for any country may evolve. Please,
check with the local authorities for the latest status of their
national regulations for both 2.4GHz. and 5GHz. wireless
LANs.
Please, be compliant to local regulations declaring your country
and the real gain value of antenna system in software
configuration by means the following commands:
¾ world-mode dot11d
¾ antenna gain
Note, the value of antenna gain is related to the whole antenna
system; that includes the gain of installed antenna and power
absorption effects (loss) caused by coax cables, connectors and
any other objects like, in example, N-way splitter/combiner.
The maximum permitted antenna-gain value is 27dBi in the
5500-5700MHz band, 22dBi in the 5150-5350MHz band and
18dBi in the 2.4GHz band.
Local language safety statements
Please, go to the Allied Telesis website
http://www.alliedtelesis.com/
for the translated safety
statement in your language
.
Allied Telesis 2 www.alliedtelesis.com
AT-WR4662n | High-Speed Mobility - Wireless Base Router
Hardware Installation
For connecting the equipment to the wired network, a
pre-assembled CAT 5 cable with outdoor waterproof RJ45
connector installed shall be used or the provided RJ45 assembly
can be field installed on a CAT 5 outdoor rated cable as shown
in Figure 3.
Package Content
Check your package for the following items. If any item is
missing or damaged, contact your Allied Telesis sales
representative for assistance.
x 1x AT-WR4662n unit (802.11n, with 2x2 MIMO)
x 2x protective caps for N-type connector
x 1x field installable RJ-45 connector kit
x 1x pole mount kit with screws, U-bolts and nuts
x 1x this Quick Installation Guide
Hardware description
The device has the following connection points:
x 4x antenna connectors, N-Type - female
x 1x Ethernet port, IEEE802.3af PoE
Figure 1 depicts how the rating label on the equipment back
indentifies th
e antenna connectors.
The antenna connectors are identified as:
0a - interface dot11radio 0, MIMO chain 0
0b - interface dot11radio 0, MIMO chain 1
1a - interface dot11radio 1, MIMO chain 0
1b - interface dot11radio 1, MIMO chain 1
Figure 1: AT-WR4662n antenna connectors
Figure 2 shows the bottom of the device offering N-type
connectors, the
Ethernet PoE connector and the protective
vent.
Figure 3: Weather proof RJ45 connector assembly
Mechanical Installation
Installing the device, first attach the provided pole mount
bracket or the optional AT-WR4501 wall mount bracket using
the 4 bolts provided with the equipment.
Figure 4: HSMIP Base Router mounted on pole
For pole installation mount the two provided U bolts as shown
in Figure 4 and fasten the four provided nuts until the
equipment i
s firmly held. Please do not exceed in order to avoid
mechanical deformation of bolts or mounting kit. For wall
mounting you will need to order the AT-WR4501 Wall Mount
kit.
Grounding the unit
On your pole always use proper wire grounding techniques in
accordance with your local electric codes. External antennas
must be properly grounded too.
Powering the unit
Figure 2: The bottom of AT-WR4662n
The device requires IEEE 802.3af PoE power feeding; attach
power sourcing
equipment (PSE) to the RJ45 PoE connector.
USE ONLY PSE which is compliant to IEEE 802.3af, otherwise
you can seriously damage the device.
Allied Telesis 3 www.alliedtelesis.com