Installation Manual

ManualsBrandsAltronix ManualsData UTP8 Channel Passive UTP Transceiver Hub with Integral Camera Power w/8 HubWayAv Video Balun/Combiners

- 4 - HubSat8D

2. Plug the RJ45 connector at one end of the CAT-5 or higher structured cable into the RJ45 jack marked [PVD1]

on Circuit Board A (F

ig. 1i, pg. 4). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured

cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1.

• For 24VAC cameras use Altronix model HubWayAv Video Balun/Combiner (F

igs. 2a, 2b, pg. 6).

• For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner (Figs. 2c, 2d, pg. 6).

•

For non-isolated 12VDC cameras use Altronix model HubWayDvi Video Balun/Combiner (Figs. 2c, 2d, pg. 6).

The total cab

le distance must not exceed 750 ft. for video transmission between the HubSat8D and each camera.

Repeat this step for all other camera channels [PVD2-4] on Circuit Board A and [PVD1-4] on Circuit Board B.

3. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 6) power

LEDs (Green) of the HubSat8D will illuminate w

hen AC power is present (Fig. 1e, pg. 4) and HubWayAv, HubWayDv

or HubW

ayDvi Video Balun/Combiner LEDs will illuminate indicating power is present (Fig. 2b, 2d, pg. 6).

4. Measure the output voltage at each Video Balun/Combiner (Figs. 2b, 2d, pg. 6) before making connections to

each camera to insure proper operation and a

void possible damage.

5. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 4a, pg. 6).

. Connect power outputs of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners to power inputs

of cameras (Figs. 2a-2d, pg. 6). Polarity must be observed.

•

HubWayAv - Terminals marked [AC POWER] (Figs. 2a, 2b, pg. 6).

•

HubWayDv/HubWayDvi - Terminals marked [– 12VDC +] (Figs. 2c, 2d, pg. 6).

. Connect the terminals marked [+ DATA -- ] of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners

to data input terminals of cameras for PTZ control (Figs. 2b-2d, pg. 6). Polarity must be observed.

When using fixed cameras disregard this step.

. Connect the BNC connector of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners to the

BNC video outputs of cameras (Figs. 2b-2d, pg. 6).

9. Set illuminated master pow

er disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg

. 6).

Fig. 1 - HubSat Circuit Board A / HubSat Circuit Board B

PVD1

VIDEO1 VIDEO2 VIDEO3 VIDEO4

PVD2 PVD3 PVD4

+ DATA -

DATA 1-4 VIDEO 1-4

28VAC

24VAC

28VAC

24VAC

28VAC

24VAC

28VAC

24VAC

OFF

UX1 AUX2

UX3 AUX4

1a - BNC Connector: Video in from remote camera

video out to DVR.

1b - Output PTCs: Protects each output.

1c - Power Terminals: 24VAC/28VAC power outputs.

1d - Output Voltage Switches: Selects

24V

AC/28VAC/OFF for each output.

1e - LED(s) 1-4: Pow

er output indicators.

1f - Data: RS422/RS485 input from head end equipment

VR) for PTZ control.

1g - Channels 1-4: Single CAT-5 or higher structured

cab

le out to HubWay, HubWayLD or HubWayLDH enables

transmission of up to four (4) video signals.

1h - Data: CAT-5 or higher structured cable to data port

on HubW

ay, HubWayLD or HubWayLDH or head end

equipment (DVR).

1i - Channels 1-4: CAT-5 or higher structured cable

to cameras.

1g1h