Installation

ManualsBrandsAltronix ManualsData UTP8 Channel Passive UTP Hub/Balun Kit, 115/230VAC

Rev. 070908

Passive UTP Transceiver Hub

with Integral Camera Power

Installation Guide

Models Include:

HubWay8DS

- UL Listed eight (8) Channel Passive UTP Transceiver Hub with Integral Camera Power

HubWay82DS

- UL Listed eight (8) Channel Passive UTP Transceiver Hub with Integral Camera Power

- Includes eight (8) UL Listed Accessory HubWayAv Video Balun/Combiners

HubWay83DS

- UL Listed eight (8) Channel Passive UTP Transceiver Hub with Integral Camera Power

- Includes eight (8) UL Listed Accessory HubWayDv Video Balun/Combiners

More than just power.

Video • Data • Power

Summary of content (8 pages)

PAGE 1
Video • Data • Power Passive UTP Transceiver Hub with Integral Camera Power Installation Guide Models Include: HubWay8DS - UL Listed eight (8) Channel Passive UTP Transceiver Hub with Integral Camera Power HubWay82DS - UL Listed eight (8) Channel Passive UTP Transceiver Hub with Integral Camera Power - Includes eight (8) UL Listed Accessory HubWayAv Video Balun/Combiners HubWay83DS - UL Listed eight (8) Channel Passive UTP Transceiver Hub with Integral Camera Power - Includes eight (8) UL Listed Accesso
PAGE 2
Overview: Altronix HubWay8DS Passive UTP Transceiver Hub w/Integral Camera Power transmits UTP video, RS422/RS485 data and power over a single CAT-5 or higher structured cable. Unit provides 8 camera channels in a space saving 1U EIA 19” rack mount chassis which may be rack, wall or shelf mounted. Video transmission range is up to 750 ft. max. per channel. Units are compatible with AC and/or DC fixed or PTZ cameras when utilizing Altronix HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners.
PAGE 3
7. Connect the BNC video outputs for HubWay8DS Channels 1-8 to the corresponding video inputs on the head end equipment (DVR) (Fig. 1d, pg. 4). 8. Connect the RS422/RS485 output of the head end equipment (DVR) to the data input terminal block of the HubWay8DS unit (polarity must be observed) (Fig. 1c, pg. 4). 9. Connect Video Balun/Combiner at camera 1 to the HubWay8DS unit utilizing CAT-5 or higher structured cable.
PAGE 4
-4- Rear 8 7 6 5 1-8 CH 1-4 -- DATA + 4 1f - Channels 1-4 & Channels 5-8: Links HubSat units enabling video transmission of up to four (4) cameras over a single CAT-5 structured cable. CH 5-8 24VAC OFF 28VAC 1b - LED(s) 1-8: Power indicators. 1a - Output voltage switches: Selects 24VAC/28VAC/OFF for each output. Fig. 1 3 2 Top View 1 + -- HubWay Passive Unit 8 7 6 5 4 1d - BNC Connector: Video outputs to head end equipment (DVR).
PAGE 5
Po we rL ED Ty pe Ca m era Ou t to put V ca o m lta era ge Altronix Model Number In p fro ut V m o un H ltag it ub e W ay HubWayAv, HubWayDv and HubWayDvi Video Balun/Combiners: HubWayAv *24VAC/28VAC *24VAC/28VAC 24VAC cameras Green HubWayDv *24VAC/28VAC 12VDC 12VDC cameras Red HubWayDvi *24VAC/28VAC 12VDC electronically isolated 12VDC cameras without isolation Red *Based on camera load and structured cable length. Fig. 2 Fig. 2c Fig.
PAGE 6
-6- HubWay Passive Unit CAT-5 CAT-5 6 115VAC Input, 50/60Hz 24VAC/28VAC Camera Power Provided by HubSat4D Data (CAT-5) 7 5 4 3 2 Fixed Camera Video (Coax) Power PTZ Camera Video Data Power HubWayAv Video Balun Combiner CAT-5 1-8 CH 1-4 -- DATA + Fig. 4a - Optional hookup utilizing HubSat4D.
PAGE 7
1U EIA 19” Rack Mount Chassis Mechanical Drawing & Dimensions: 1.625”H x 19.125”W x 8.5”D REAR -- DATA + 24VAC OFF 28VAC 1.625" CH 5-8 8 7 6 5 1-8 CH 1-4 4 3 2 1 8 7 6 5 4 3 2 1 AC POWER TOP & BOTTOM 17.625" 8.5" FRONT 19.125" .75" Fig. 5 Illuminated master power disconnect circuit breaker: • OFF position Circuit breaker tripped – Switch not illuminated. • RESET (ON) position – Switch illuminated.
PAGE 8
Mounting Options: Rack Mount Installation 1- Remove and discard factory installed screws from both sides of rack chassis (Fig. 6a). 2- Install mounting brackets (A) on the left and right side of rack chassis using the four (4) flat head screws (B) (included) (Fig. 6b). 3- Place unit into desired EIA 19” rack position and secure with mounting screws (not included) (Fig. 6c). Fig. 6 Fig. 6b Fig. 6a Fig.