Manualshelf

Installation Instructions

ManualsBrandsAltronix ManualsAccess Control Power productsNetwork Power Distribution Module
12345678910
- 10 - LINQ8PD/LINQ8PDCB
Battery Monitor Configuration (Fig. 7, pg. 10): The LINQ8PD(CB) displays the real time battery health.
Select Description
Battery Capacity Enter the battery rating in amp hours.
Battery Charge Level Enter the estimated percentage charge level of the Battery at the time of installation.
Max. Battery
Discharge Current
Enter the high current limit to be drawn from the battery in the event of a power failure. If this limit is exceeded an
SNMP trap message and/or email notification will be generated.
Max. Charge Current
Enter the maximum charge current of the connected power supply. If this limit is exceeded an SNMP trap message and/or
email notification will be generated.
Battery Service Date
Enter the date on which the installed batteries need to be serviced. An SNMP trap message and/or email notification will be generated on the entered date.
Note: Batteries should be inspected at least once a year. Even though the expected battery life is 5 years,
it is recommended changing batteries in 4 years.
Output Relay configuration (Fig. 7, pg. 10):
Three (3) output relays of the LINQ8PD(CB) can be configured for various uses. From the pull down menu select the desired setting for each relay.
Output Relay 1:
Setting Description
AC The relay will energize when AC trouble is detected.
Com Trouble The relay will energize when on all trouble conditions.
Output Relay 2:
Battery The relay will energize when Battery trouble is detected.
Tamper The relay will energize when the tamper input is triggered.
Output Relay 3
FACP The relay will energize when the FACP input is triggered.
Tamper The relay will energize when the tamper input is triggered.
Output Configuration (Fig. 8, pg. 10):
Field Name Description
Device ID Enter a descriptive name for the device connected to the output.
Current High/Low
Enter both the high current limit and low current limit in the appropriate fields for the connected Device.
If either of these limits are exceeded an SNMP trap message and/or email notification will be generated.
Voltage High/Low
Enter both the high voltage limit and low voltage limit in the appropriate fields for the connected Device.
If either of these limits are exceeded an SNMP trap message and/or email notification will be generated.
Device Management Interface
Setup
Site ID: Enter Location
Enter ID
Enter ID
Update Site ID
Sync with computer
Minimize Others
Submit Settings
Minimize
Update
Monday, Sept. 21 2015 [2:30 pm]
PS1 Volts High Limit
PS1 Volts Low Limit
PS1 Amps High Limit
PS1 Amps Low Limit
PS2 Volts High Limit
PS2 Volts Low Limit
PS2 Amps High Limit
PS2 Amps Low Limit
Output Device ID Current High (A) Current Low (A) Voltage High (V) Voltage Low (V) FACP Trigger Battery Backup Output Status
27.7
4
3
0
V
V
A
A
V
V
A
A
14
10.01
5
0
Bat Capacity
Bat Charge Level
Max Battery
Discharge Current
Max Charge Current
7
90
2.75
0.9
AH
%
A
A
Battery Service Date
Output Relay 1
Output Relay 2
Output Relay 3
02 /02 / 2015
Com Trouble
Tamper
FACP
FACP Trigger
Output Reset Trigger
Input Function
Max Temp
Dry
N.C.
Reset
50 C
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
Latching Ye s
No No
Battery PresencePS2 Presence
No
Yes
No
Yes
No
Yes
No
Non-Latching
Inactive
Latching
Non-Latching
Inactive
Latching
Non-Latching
3
3
3
3
3
3
3
3
27.70
0
0
0
0
0
0
0
3
3
3
3
3
3
3
3
1
2
3
4
5
6
7
8
Enter ID
Enter ID
Enter ID
Enter ID
Enter ID
Enter ID
Enter ID
27.7
27.7
27.7
27.7
27.7
27.7
27.7
Events Log HelpSecurity SettingsNetwork SettingsSetupStatus
A
B
D EC
Fig. 7
Device Management Interface
Setup
Site ID: Enter Location
Enter ID
Enter ID
Update Site ID
Sync with computer
Minimize Others
Submit Settings
Minimize
Update
Monday, Sept. 21 2015 [2:30 pm]
PS1 Volts High Limit
PS1 Volts Low Limit
PS1 Amps High Limit
PS1 Amps Low Limit
PS2 Volts High Limit
PS2 Volts Low Limit
PS2 Amps High Limit
PS2 Amps Low Limit
Output Device ID Current High (A) Current Low (A) Voltage High (V) Voltage Low (V) FACP Trigger Battery Backup Output Status
27.7
4
3
0
V
V
A
A
V
V
A
A
14
10.01
5
0
Bat Capacity
Bat Charge Level
Max Battery
Discharge Current
Max Charge Current
7
90
2.75
0.9
AH
%
A
A
Battery Service Date
Output Relay 1
Output Relay 2
Output Relay 3
02 /02 / 2015
Com Trouble
Tamper
FACP
FACP Trigger
Output Reset Trigger
Input Function
Max Temp
Dry
N.C.
Reset
50 C
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
Latching Yes
No No
Battery PresencePS2 Presence
No
Yes
No
Yes
No
Yes
No
Non-Latching
Inactive
Latching
Non-Latching
Inactive
Latching
Non-Latching
3
3
3
3
3
3
3
3
27.70
0
0
0
0
0
0
0
3
3
3
3
3
3
3
3
1
2
3
4
5
6
7
8
Enter ID
Enter ID
Enter ID
Enter ID
Enter ID
Enter ID
Enter ID
27.7
27.7
27.7
27.7
27.7
27.7
27.7
Events Log HelpSecurity SettingsNetwork SettingsSetupStatus
A
B
D EC
Fig. 8