Installation Instructions

ManualsBrandsAltronix ManualsAccess Control Power productsNetwork Power Distribution Module

LINQ8PD/LINQ8PDCB - 7 -

1. Network setup:

Click [Network Settings] tab. This will open the Network Setting screen. In this screen the

MAC Address of the LINQ8PD(CB) module will be found along with the programming fields

for the Network Settings, Trap Receiver Settings, SNMP Port Settings and Email Settings.

Network Settings (Fig. 3a, pg. 7):

In the IP Address Method field select the method that the IP Address for the LINQ8PD(CB)

will be obtained “Static” or “DHCP” then follow the appropriate steps.

STATIC (Fig. 3a, pg. 7):

Field Name Description

IP Address Enter the IP address assigned to the LINQ8PD(CB) by the network administrator.

Subnet Mask Enter the Subnet of the network.

Gateway

Enter the TCP/IP gateway of the network access point (router) being used

Note: Gateway configuration is required to properly receive emails from

the device.

HTTP Port

Enter the HTTP port number assigned to the LINQ8PD(CB) module by the

network administrator to allow remote access and monitoring. The default inbound

port setting is 80. HTTP is not encrypted and unsecure. Even though HTTP can be

used for remote access it is recommended primarily for use with LAN connections.

HTTPS Port

Enter the HTTPS port number assigned to the LINQ8PD module by the

network administrator to allow remote access and monitoring. The default inbound

port setting is 443. Being encrypted and more secure HTTPS is highly

recommended for remote access.

System Port

Used to update device firmware. Enter the port number assigned to the

LINQ8PD(CB) module by the network administrator. Default Port setting 667*

a. Click [Submit Network Settings] button, a dialog box will display

“New network settings will take effect after the server is rebooted” click “OK”.

DHCP (Fig. 3a, pg. 7):

After selecting DHCP in the IP Address Method field click [Submit Network Settings] button, a dialog box will display “New network settings will take effect after the server is

rebooted” click “OK”. Next click [Reboot Server] button. After rebooting the LINQ8PD(CB) will be set in the DHCP mode. The IP address will be assigned by the router when

the LINQ8PD(CB) is connected to the network. It is recommended to have the assigned IP Address reserved to ensure continued access (see the network administrator).

Field Name Description

Subnet Mask When operating in DHCP the router will assign the subnet mask values.

Gateway TCP/IP gateway of the network access point (router) being used will be displayed.

HTTP Port

Enter the HTTP port number assigned to the LINQ8PD(CB) module by the network administrator to allow remote access and monitoring. The default inbound

port setting is 80. HTTP is not encrypted and unsecure. Even though HTTP can be used for remote access it is recommended primarily for use with LAN con-

nections.

HTTPS Port

Enter the HTTPS port number assigned to the LINQ8PD(CB) module by the network administrator to allow remote access and monitoring.

The default inbound port setting is 443. Being encrypted and more secure HTTPS is highly recommended for remote access.

System Port Used to update device firmware. Enter the port number assigned to the LINQ8PD(CB) module by the network administrator. Default Port setting 667*

Click the [Submit Network Settings] button, a dialog box will display “New network settings will take effect after the server is rebooted” click “OK”.

Device Management Interface

Network Settings

Site ID: LINQ8

Monday, Sept. 21 2015 [2:30 pm]

Submit Network Settings

Submit Email SettingsSubmit Test Email

Submit Trap Receiver IP Settings

Submit Port Settings

Restore Factory Settings

Reboot Server

IP Address Method:

IP Address:

Subnet Mask:

Gateway:

HTTP Port:

HTTPS Port:

System Port:

MAC Address:

BC:34:00:30:01:72

STATIC

192.168.168.107

255.255.255.0

192.168.0.11

443

667

SNMP Port:

Trap Message Port:

161

162

Trap Receiver IP Address 1:

Trap Receiver IP Address 2:

Trap Receiver IP Address 3:

Trap Receiver IP Address 4:

Trap Receiver IP Address 5:

192.168.168.200

From:

Subject:

Username:

Password:

SMTP server IP:

SMTP server Port:

Outgoing Email Address 1:

Outgoing Email Address 2:

Outgoing Email Address 3:

Outgoing Email Address 4:

Outgoing Email Address 5:

event.report@linqinfo

event.report

• • • • • • • •

smtp.gmail.com

587

Network Settings:

Trap Receiver Settings:

SNMP Port Settings:

Email Settings:

Events Log HelpSecurity SettingsNetwork SettingsSetupStatus

Fig. 3