Power over the Ethernet PoE Managed Midspan Solution for Standard Network Infrastructure Installation Guide Models Include: NetWay8M - Eight (8) Port PoE Midspan Injector DOC#: NETM Rev. 052110 NetWay16M - Sixteen (16) Port PoE Midspan Injector More than just power.
Overview: Altronix NetWay8M/NetWay16M Managed Midspans provide power and pass data for PoE compliant cameras/edge devices. Cameras/edge devices may be located up to 100m (328 ft.) from the NetWay unit. A NetWayXT repeater module can be utilized to extend the distance an additional 100m (328 ft.) for a total range of up to 200m (656 ft.). A maximum range of 600m (1968 ft.) is possible using multiple repeaters, based on camera/device port requirement.
Note: All interconnected devices must be UL Listed. 7. Upon completion of wiring set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 1g, pg. 3). 8. Port status LEDs on the NetWayM will initialize when PoE devices are connected as follows: - LED will illuminate when devices are IEEE 802.3af compliant. - LED will blink once and illuminate when devices are IEEE802.3at compliant (PoE Plus). 9. To utilize the PoE shutdown feature it is necessary to do the following: a.
1g 1h Illuminated master power disconnect circuit breaker (switch): • OFF position Circuit breaker tripped Switch not illuminated. • RESET (ON) position Switch illuminated. IEC 320 Connector: 115VAC 60Hz (grounded line cord included). Installing a NetWay1512 adapter for 12VDC IP cameras up to 13W: 1. Mount NetWay1512 in proximity to IP camera (Fig. 2, pg. 4). Affix one side of velcro (supplied) to NetWay1512 and the place the second side of the velcro in the desired location. 2.
NetWay8M/NetWay16M Typical Application: Fig. 4 NetWayXT Extends Ethernet 100m (328 ft.) NetwayXT Repeater PoE Camera www.altronix.com Power OUT IN PoE Camera PoE + Camera NetWay1512 Netway1512 Typical UL294 Application: Card Reader I.T.E. 43KC Adapter www.altronix.com IN OUT 12VDC + Output --- 12VDC IP camera Strike HID Solo NetWay8M + PoE -SHUTDOWN Programming and Status Ethernet Switch NVR/Network Server Technical Specifications: Parameter Description No.
NetWay8M/NetWay16M User Interface and Programming: Note: A constant PC connection is not required for proper operations and is used as a local programming/monitoring tool only. Step 1. Set Local Area Connection of your laptop to DHCP mode. For Windows XP: a. Open Network Connections by clicking Start button, then clicking Settings, then clicking Network Connections. b. Right click the Local Area Connection. Click Properties.
PoE port setup: Individual ports may be disabled if those ports are not used or to avoid the connection of unauthorized PoE devices. 1. To disable one or more ports click on the Disable radio button(s) in the PoE column (Fig. 5, pg. 7). 2. To enable one or more ports click on the Enable radio button(s) in the PoE column (Fig. 5, pg. 7). Note: To enable all ports click on the Enable All link below PoE column. 3. Click Submit to save the changes or proceed with programming.
Configuring NetWay8M/NetWay16M for network connection: Since every Network Configuration is different, please check with your Network Administrator to see if your NetWay8M/ NetWay16M should use static IP addresses, or DHCP assigned IP addresses and/an Inbound Port assignment prior to setting up network connection. 1. Click Network Settings link. If you are prompted for an administrative password, type and submit the password. Note: Default settings have password requirements turned off . 2.
The default port for NetWay8M/NetWay16M is: 80 Note: Port 80 is the default port used for web browsing. Because of this, in order to prevent the average user from hosting a web server, most ISPs BLOCK traffic using port 80 from reaching the average site. If you only plan to monitor your NetWay8/NetWay16M on a LAN, you can use port 80, and don’t have to concern yourself with routers.
NetWay8M/NetWay16M Rack Mount Chassis Mechanical Drawing & Dimensions: Fig. 7 + PoE -SHUTDOWN + PoE -SHUTDOWN 19.125" .75" 17.625" 8.5" 1.625" AC POWER (ON) The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the presence of an insulated “DANGEROUS VOLTAGE” within the products enclosure that may be of sufficient magnitude to constitute an electric shock.
Mounting Options: Rack Mount Installation 1- Remove and discard factory installed screws from both sides of rack chassis (Fig. 8a). 2- Install mounting brackets (A) on the left and right side of rack chassis using the four (4) flat head screws (B) (included) (Fig. 8b). 3- Place unit into desired EIA 19” rack position and secure with mounting screws (not included) (Fig. 8c). Fig. 8 Fig. 8a Fig. 8b Fig.
Notes: Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice. 140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056 website: www.altronix.com, e-mail: info@altronix.com, Made in U.S.A.