Installation Guide

ManualsBrandsAltronix ManualsAutomation & Security8-Door Access and Power Integration Kit Includes Trove2PX2 with eFlow104NB, ACM8, VR6, PDS8

T2PXK7F8

8 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove2 enclosure with TPX2 Altronix/Paxton backplane

- One (1) eFlow104NB - Power Supply/Charger

- One (1) ACM8 - Fused Access Power Controller

- One (1) VR6 - Voltage Regulator

- One (1) PDS8 - Dual Input Fused Power Distribution Module

Access & Power Integration

Rev. 040419

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

All registered trademarks are property of their respective owners. More than just power.™

Installation Guide

All components of this Trove kit are UL Listed sub-assemblies.

Please refer to the included corresponding Sub-Assembly Installation Guides for further information.

Summary of content (4 pages)

PAGE 1
Access & Power Integration T2PXK7F8 8 Door Kit with Fused Outputs Fully assembled kit includes: - Trove2 enclosure with TPX2 Altronix/Paxton backplane One (1) eFlow104NB - Power Supply/Charger One (1) ACM8 - Fused Access Power Controller One (1) VR6 - Voltage Regulator One (1) PDS8 - Dual Input Fused Power Distribution Module All components of this Trove kit are UL Listed sub-assemblies. Please refer to the included corresponding Sub-Assembly Installation Guides for further information.
PAGE 2
Overview: Altronix T2PXK7F8 Trove Paxton kit is pre-assembled and consists of Trove2PX2 enclosure/backplane with factory installed Altronix power supply/charger and sub-assemblies. T2PXK7F8 kit also accommodates up to eight (8) Paxton Net2 Plus modules for up to eight (8) doors in a single enclosure. 24VDC @ 9.7A 20.2826.4 8 8 10A/ 2.5A/ 10A/ 250V 250V 32V PDS8 Board Output Fuse Rating 20.1726.
PAGE 3
Configuration of Paxton Net2 Plus Modules: 1. Align the Paxton Net2 Plus modules on the backplane to match the modules’ mounting holes with corresponding pems. 2. Fasten spacers (provided) onto metal pems (Fig. 2a, pg. 3). 3. Mount Paxton Net2 Plus modules to spacers utilizing pan head screws (provided) (Fig. 2a, pg. 3). Note: Paxton Net2 Plus modules have one (1) RJ45 jack and one (1) switch each. Please make sure that they are mounted correctly, as shown in Fig. 2 below. 4.
PAGE 4
Enclosure Dimensions (H x W x D approximate): 27.25” x 21.5” x 6.5” (692.15mm x 546.1mm x 165.1mm) 21.50” (546.1mm) 5.25” (133.35mm) 3.5”(88.9mm) 3.5”(88.9mm) 5.25” (133.35mm) 0.685” (17.4mm) 1.25” (31.8mm) 6.25” (158.8mm) 1.25” (31.8mm) 0.5625” (14.3mm) 1.77” (45mm) 2.415” (61.3mm) 1.5” (38.1mm) Knockouts 1.125” (28.3mm) 0.885” (22.5mm) 2.00” (50.8mm) 6.25” (158.8mm) 2.00” (50.8mm) 19.80” (502.9mm) 8.00” (203.2mm) 27” (685.8mm) 8.25” (209.5mm) 6.75” (171.5mm) 2.00” (50.8mm) 0.85” (21.