Installation Guide

ManualsBrandsAltronix ManualsAccessoriesAccess & Power Integration Solution

Trove2SH2/TSH2 - Altronix/Software House - 1 -

Overview:

Trove2SH2 accommodates various combinations of Software House boards with or without Altronix

power supplies and accessories for access systems.

Specifications:

• 19 Gauge grey enclosure with ample knockouts for convenient access.

Enclosure Dimensions (H x W x D): 27.25” x 21.75” x 6.5” (692.15mm x 552.45mm x 165.1mm).

Trove2SH2

- Trove2 enclosure with TSH2 Altronix/Software House backplane.

• Includes: tamper switch, cam lock, lock nuts and mounting hardware.

TSH2

- TSH2 Altronix/Software House backplane.

• 19 Gauge backplane.

• Includes mounting hardware.

Dimensions (H x W x D): 25.375” x 19.375” x 0.3125” (644.525mm x 492.125mm x 7.9mm).

Backplane accommodates a combination of the following:

• Two (2) AL400ULXB2, AL600ULXB, AL1012ULXB, AL1024ULXB2,

eFlow4NB, eFlow6NB, eFlow102NB or eFlow104NB.

• One (1) ACM4(CB), ACM8(CB), MOM5, PD4UL(CB), PD8UL(CB), PDS8(CB), VR6.

• One (1) iStar Ultra GCM and two (2) iStar Ultra ACM.

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all

local codes and authorities having jurisdiction. Product is intended for indoor use only.

1. Remove backplane from enclosure. Do not discard hardware.

2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure.

Install three upper fasteners and screws in the wall with the screw heads protruding.

Place the enclosure’s upper keyholes over the three upper screws, level and secure.

Mark the position of the lower three holes. Remove the enclosure.

Drill the lower holes and install the three fasteners. Place the

enclosure’s upper keyholes over the three upper screws.

Install the three lower screws and make sure to

tighten all screws.

3. Mount UL Listed tamper switch (Included)

(Ademco model 112 or equivalent) in desired location,

opposite hinge. Slide the tamper switch bracket onto

the edge of the enclosure approximately 2” from the

right side (Fig. 1, pg. 1). Connect tamper switch

wiring to the Access Control Panel input or the

appropriate UL Listed reporting device.

To activate alarm signal open the door of the enclosure.

4. Mount Altronix/Software House boards to backplane,

refer to page 2.

Edge of

Enclosure

to Access Control Panel

or U.L. Listed

Reporting Device

Enclosure

Honeywell

model # 112

Tamper Switch

or equivalent

(provided)

Fig. 1

Rev. 062416

Installation Guide

Versatile Access Power and Integration Enclosures

Trove2SH2 TSH2

- Trove2 enclosure with - Altronix/Software House backplane only

Altronix/Software House backplane (TSH2)

Metal or Nylon Standoff

5/16” Pan Head Screw

Lock Nut

Summary of content (4 pages)

PAGE 1
Rev. 062416 Installation Guide Versatile Access Power and Integration Enclosures Trove2SH2 - Trove2 enclosure with Altronix/Software House backplane (TSH2) TSH2 - Altronix/Software House backplane only Overview: Trove2SH2 accommodates various combinations of Software House boards with or without Altronix power supplies and accessories for access systems. Specifications: • 19 Gauge grey enclosure with ample knockouts for convenient access. Enclosure Dimensions (H x W x D): 27.25” x 21.75” x 6.
PAGE 2
TSH2: Configuration of Altronix Power Supply and/or Sub-Assembly Boards and Software House Boards 1. Fasten standoffs (provided) to pems that match the hole pattern for Altronix Power Supply/Chargers or Altronix Sub-Assembly boards (Fig. 2, pg. 2). Fasten metal standoffs in the correct locations to provide proper grounding, see below (Fig. 2, pg. 2). 2. Mount boards to standoffs utilizing 5/16” pan head screws (provided) (Fig. 2, pg. 2). 3.
PAGE 3
TSH2 Dimensions Fig. 3 19.4” (492.76mm) 7.5” (190.5mm) 24.95” (633.73mm) 7.5” (190.5mm) 0.156” ( 3.96mm) 12.62” (320.55mm) 16.245” (412.62mm) 25.4” (645.16mm) 8.495” (215.77mm) 12.62” (320.55mm) 0.45” (11.43mm) 1.0” (25.4mm) 7.5” (190.5mm) 1.0” (25.4mm) 7.5” (190.5mm) 9.2” (233.
PAGE 4
Trove2SH2 Enclosure Dimensions (H x W x D): 27.25” x 21.75” x 6.5” (692.15mm x 552.45mm x 165.1mm) 21.50” (546.1mm) 2.00” (50.8mm) 5.25” (133.35mm) 3.50” (88.9mm) 3.50” (88.9mm) 5.25” (133.35mm) 0.685” (17.399mm) 1.25” (31.75mm) 0.5625” (14.29mm) 1.77” (44.96mm) 2.415” (61.34mm) Knockouts 1.125” (28.32mm) 0.885” (22.479mm) 6.25” (158.75mm) 0.85” (21.59mm) 6.25” (158.75mm) 1.25” (31.75mm) 19.80” (502.92mm) 1.5” (38.1mm) 2.00” (50.8mm) 6.75” (171.45mm) G 8.25” (209.54mm) 27.00” (685.8mm) 8.