Instruction Manual

ManualsBrandsAlumax ManualsFor Home390c Supplement

Page 1 of 5 EPH-N00-06088

6-3-02

STIKSTALL

INSTRUCTION SUPPLEMENT

390c CONTINUOUS HINGE

FRAMELESS DOOR KIT

This Alumax 390c Continuous Hinge door panel kit is designed to

be installed in our StikStall framework with an inline panel (391), a

return panel (392), an inline and a return panel (393), a neo-angle

unit (394), or between two inline panels (395).

To ensure correct installation, this instruction supplement (packed

with a glazed or KD door panel kit) is designed to be used with a

StikStall Installation Instruction sheet (391, 392, 393, 394, 395) that

will be packaged with the corresponding StikStall frame kit. Each

step in the primary instruction sheet will indicate whether it applies

to all door types or if this supplement should be used.

%$7+(1&/2685(6

Tel:

Fax:

800-643-1514

870-234-3181

www.alumaxbath.com

An Alcoa Company ®

Summary of content (5 pages)

PAGE 1
%$7+ (1&/2685(6 An Alcoa Company ® Tel: 800-643-1514 Fax: 870-234-3181 www.alumaxbath.com 390c CONTINUOUS HINGE FRAMELESS DOOR KIT STIKSTALL INSTRUCTION SUPPLEMENT This Alumax 390c Continuous Hinge door panel kit is designed to be installed in our StikStall framework with an inline panel (391), a return panel (392), an inline and a return panel (393), a neo-angle unit (394), or between two inline panels (395).
PAGE 2
390 PARTS LIST *A. *B. *C. *D. *E. *F. *G. *H. *J. *K. *L. *M. *N. 1 Glazed Door Panel 1 Strike Jamb with Magnet 2 Snap-in Fillers 6 #8 x 1/4" Truss Head Screws 1 Handle Vinyl 1 Pull Handle 1 Drip Rail 1 Tapered Drip Vinyl 1 Roll of Double Stick Tape 1 #6 x 3/8" Pan Head Screws 1 Set Drip Rail Plugs 1 Bottom Rail 1 Rail End Cap & $ % ' ' ) ( / * .
PAGE 3
1 NOTE: Obscure glass doors should be installed with the rough surface of the glass to the exterior of the unit. Silk Screened or etched glass doors should be installed with the patterned surface to the inside. Determine which end of the door will be the bottom. Using a mallet or a hammer and wood block (never a hammer alone), carefully drive the bottom rail over the bottom edge of the glass and vinyl, snug to the factory installed vertical rail.
PAGE 4
Pull the bottom end of the hinge jamb tight to the curb filler [*C] and plumb the jamb. Drill two 1/8" holes thru the hinge jamb and into the wall jamb (or post) 3/8" to 3/4" from the wall and approximately 1/4" vertically from the ends of the jamb. Drill a third hole centered between the first two and enlarge the outer holes with a 3/16" drill for clearance on the self-tapping screws. Attach the hinge jamb/door panel permanently with three #8 x 1/ 4" truss head screws [*D].
PAGE 5
7 Adjust the drip vinyl [*H] by sliding it left or right until it just touches the curb. Trim the vinyl flush with the hinge side and notch 1/2" longer than the drip rail [*G] as shown on the strike side. Slide the vinyl into the drip rail and secure it on the hinge side of the drip rail with one #6 x 3/8" truss head screw [*K]. The drip plug [*L] is supplied with a left and right hand plug together. Break the two pieces apart and insert the appropriate plug into the high (strike) side of the drip rail.