M-94Z INSTRUCTION MANUAL Neo Angle Shower door 08.
Please keep this manual and product code number for future reference and replacement parts ordering if necessary. GENERAL INSTRUCTIONS • Read this manual carefully and completely before proceeding. • It is recommended that you wear safety glasses at all times during the installation. INSTALLATION OVER CERAMIC TILES • Silicone should be used to seal the gap where the ceramic tiles meet the panel.
INSTALLATION MANUAL TOOLS AND MATERIAL REQUIRED LONG NOSE LOCKING PLIER (X2) SCREWDRIVERS SILICONE BLOCK CUTTING PLIER TAPE MEASURE MALLET PENCIL LEVEL DRILL 1/4˝& 1/8˝ DRILL BITS * To install the shower door on ceramic tiles, use a 1/4’’ drill bit for ceramic tiles SCISSOR 2 PEOPLE REQUIRED 3
INSTALLATION MANUAL INSTALLATION OF COMPONENTS FOLLOW INSTALLATION STEPS REQUIRED FOR THE MODEL STEP 7 STEP 1 • Wall Jambs Installation • Secure the expanders see page 6-8 see page 22 STEP 2 STEP 8 • Support bars installation • Fix panel assembly see page 23 see page 8-11 STEP 3 STEP 6 • Door panel assembly • Fix panel installation see page 19-21 see page 12 STEP 4 STEP 10 • Sealing • Bottom gasket installation see page 28 see page 13-15 STEP 5 STEP 9 • Door panel installation & hing
INSTALLATION MANUAL PARTS LISTING 12 12 10 11 HINGE 1 1 14 2 2 7 3 3 9 9 14 HINGE 6 8 5 13 1 5 4 4 4 ITEM PARTS QTY 1 WALL JAMB (REGULAR PUNCH) 2 2 EXPANDER 2 3 GASKET 2 4 ALUMINUM THRESHOLD 1 5 ALUMINUM “U” CHANNEL 2 6 BOTTOM GASKET 1 7 SIDE PANEL GASKET 1 8 MAGNETIC GASKET 2 9 HINGED FIXED PANEL 1 10 SIDE PANEL 1 11 DOOR PANEL 1 12 SUPPORT BAR 2 13 KNOB 1 14 HINGE 2 ITEM PARTS QTY 15 SPACING BLOCKS 2 16 WALL PLUG 7 17 SCREW CAP
INSTALLATION MANUAL WALL JAMBS INSTALLATION 1 1a. Cut-out the template before installation. 1a 1b. Place the template on the threshold of the base. 1b 1c. 1c Use the template to locate the wall jambs position on the base. Level and mark the position of the wall jambs on the wall.
INSTALLATION MANUAL WALL JAMBS INSTALLATION (CONTINUED) 1 1d. Drill holes using Ø1/8’’ drill bit and use the wall jambs holes as reference. 1d 1e. Remove the wall jambs. 1f. Insert one drop of silicone in each hole in the wall before inserting the wall plug. 1g. Before replacing the wall jambs on the base remove the template and add a drop of silicone on the bottom back of the wall jambs.
INSTALLATION MANUAL 1 WALL JAMBS INSTALLATION (CONTINUED) 1h. Screw the two wall jambs into the wall plugs by using screws 1 1/4’’ (x6). Ensure verticality with the level. 1i. Place some silicone inside the botttom of the wall jamb. 20 1h 1i 2 2a. FIX PANEL ASSEMBLY panel glass Install the hinged into the U channel temporarily. To have a correct place the U channel as shown.
INSTALLATION MANUAL 2 2b. 2b Install the panel glass into the U channel temporarily. To have a correct place the U channel as shown. 10 5/16” 5 2c. Slide temporarily the two 2d. Level the glass panels and lock the position by clamping the wall jambs and expander with pliers. panel assemblies into the two wall jambs . 2c 9 2d 10 COVER THE PLIER’S TEETH BEFOREHAND TO AVOID SCRATCHING THE ALUMINUM PARTS.
INSTALLATION MANUAL 2 FIX PANEL ASSEMBLY(CONTINUED) 2e. Use a mallet to install the side and magnetic gasket son the 2e 7 panels.
INSTALLATION MANUAL 2 2f. Unscrew the rear side of the 4 hinges as illustrated. 2f 14 2g. Fasten the front side and one of the rear side component of the hinges to the Use the provided hex. Key. *Handle showed is model (Q) panel as illustrated.
INSTALLATION MANUAL DOOR PANEL ASSEMBLY 3 3a. Screw the handle on the door as illustrated. 11 3a 13 3b. Use a mallet to install the magnetic gasket on the door panel. THE MAGNETIC GASKET MUST BE IN LINE WITH THE DOOR ON TOP. 3b 8 Hinged Fix Panel Side THE MAGNETIC GASKET IS LONGER THAN THE DOOR PANNEL AT THE BOTTOM.
INSTALLATION MANUAL 4 4a. BOTTOM GASKET INSTALLATION Cut the bottom gasket with the following path using cutting pliers.
INSTALLATION MANUAL 4 BOTTOM GASKET INSTALLATION (CONTINUED) 4b.
INSTALLATION MANUAL 4 BOTTOM GASKET INSTALLATION 4c. Use a mallet to install the bottom gasket on the door panel. 4d. Place the 2 spacing blocks under the bottom gaskets as illustrated.
INSTALLATION MANUAL 5 DOOR PANEL INSTALLATION 5a. Place the door centered on the base threshold. 5b. Align the holes of the door and panel. 2 PEOPLE REQUIRED 5b 5a INTERIOR SHOWER SIDE INTERIOR SHOWER SIDE LEVEL GLASS PANELS TO ALIGN THE HOLES.
INSTALLATION MANUAL 5 DOOR PANEL INSTALLATION(CONTINUED) 5c. Adjust the glass panels. The magnetic gaskets must be aligned and in contact. 5d. Fasten the remaining rear side component of the hinges to the door as illustrated. Use the provided hex. Key.
INSTALLATION MANUAL 5 DOOR PANEL INSTALLATION (CONTINUED) 5e. Adjust the wall jambs and the expanders so that the doors are closing properly. The magnetic gaskets must be aligned and in contact. 5f. Level and mark the positions of the U channels on the base. 5e Top view 5f 5g. Remove the back side of the hinges, the door and 5g 18 panels .
INSTALLATION MANUAL 6 FIX PANEL INSTALLATION 6a. Replace temporarily the U channels on the position marks. 6b. Drill holes through the U channels using Ø1/8’’ drill bit . 6a 6b 5 5 1” 6c. Remove the aluminum “U” channels. 6d. Insert one drop of silicone in each hole in the base before replacing the aluminum “U” channels. 6e. Screw the two aluminum 6c into the base by using screws 1 1/4’’ (x4).
6h. INSTALLATION MANUAL 6 FIX PANEL INSTALLATION (CONTINUED) 6f. Place the clear setting blocks (#22) over the screws . 6g. Insert the two panels into the wall jambs and the aluminum “U” channels 6h. Clamp the expanders and the wall jambs making sure to protect the metal surfaces. Level the glass panels and if necessary use also the clear setting blocks #23. 6i. Replace the door on the base threshold. 6g 6f 22 6h 6i COVER THE PLIER’S TEETH BEFOREHAND TO AVOID SCRATCHING THE ALUMINUM PARTS.
INSTALLATION MANUAL 6 6j. FIX PANEL INSTALLATION (CONTINUED) 6j Reinstall the back side of the hinges. 6k. Remove the spacing blocks. 6l. The magnetic gaskets must be aligned and in contact. If needed adjust the glass panels so that the doors are closing properly. 6k 6l THE MAGNETIC GASKETS MUST BE ALIGNED AND IN CONTACT.
INSTALLATION MANUAL 7 SECURE THE EXPANDERS 7a. Secure the panels with the screws 3/8” (x6) ensuring that the magnetic gaskets are still in contact . Place the caps on the heads of apparent screws. 7b. Remove the pliers after the panels are secured. 7a 18 INTERIOR SHOWER SIDE 7b REMOVE THE PLIERS.
INSTALLATION MANUAL 8 SUPPORT BARS INSTALLATION 8a. Loosen the glass clip. Align the slotte to the panel. The slotted screw head should be on the inside of the shower. panel 8b. Rest the support bar on the inside the tub. Level it and trace an arc on the wall. 8a 12 8b 8c. Isolate the wall bracket and drill a hole, using a 1/4˝ drill bit through the wall. Locate the position of this hole by way of the wall bracket. Insert a wall plug. 8d. Secure the wall bracket to the wall by way of the screw.
INSTALLATION MANUAL 9 ACCESSORIES INSTALLATION 9a Draw lines at a distance of 1/8” from the two aluminum “U” 9b Mark the lines intersections in each corner and the middle of the base as illustrated. 9c Place temporarily the aluminum threshold on the marked positions as illustrated. Place the middle of the threshold on the middle of the base. towards the outside of the shower as illustrated.
INSTALLATION MANUAL 9 ACCESSORIES INSTALLATION (CONTINUED) 9d 9d Mark on the threshold the two locations marked previousely on the base. 9e Remove the aluminium threshold. 9f Cut the aluminium threshold with the following path using cutting pliers.
INSTALLATION MANUAL 9 ACCESSORIES INSTALLATION (CONTINUED) 9g Replace the threshold on the base and mark the position .The thresholds must touch the “U” channels . Cut the two small end parts if needed. 9g THE THRESHOLDS MUST TOUCH THE “U” CHANNELS.
INSTALLATION MANUAL 9 ACCESSORIES INSTALLATION (CONTINUED) 9h Apply a bead of silicone to the underside of the threshold. 9i Replace the threshold on the base using the lines marked previously.
INSTALLATION MANUAL 10 SEALING 10a Silicone the outside of the shower, around the wall jamb, below of the U channels. panels, around the threshold and around the 10b Wait 24 hours before using the shower to dry the silicon.
