,® INSTALLATION INSTRUCTIONS UNDERCOUNTER DISHWASHER PLASTIC GIANT TUB MODELS INSTRUCTIONS D'INSTALLATION LAVN-VAISSELLE ENCASTRE MODELES A TRES GRANDE CUVE EN PLASTIQUE P % % % Table of Contents Table des matieres W10261420A ................................................ 2 ..............................................
Table of Confenfs Dishwasher Installation Safety ............................................ 2 InstallationRequirements ..................................... 3 Instructions Prepare (cont.) Dishwasher ........................................ 10 Tools and Parts............................................... 3 Make Power Cord Electrical Connection Location Requirements ....................................... 3 Determine ................................. Drain Requirements ....................
]NST TION REQUIREMENTS in addition, for first time installations Tools needed: Gather the recommended tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
*Insulation may be compressed. (not used on all models) Check that all surfaces have no protrusions that would prohibit dishwasher installation. NOTE: Shaded area of cabinet walls show where utility connections may be installed. *Measured from the lowest point on the underside Of countertop. May be reduced to 33 7%" (86 cm) by removing wheels from dishwasher. _*Minimum, measured from narrowest point of opemng.
• A new drain hose is supplied with your dishwasher. If this is not long enough, use a new drain hose with a maximum length of 12' (3.7 m)(Part Number 3385556) that meets all current AHAM/IAPMO test standards, is resistant to heat and detergent, and fits the 1" (2.5 cm) drain connector of the dishwasher. • Make sure to connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20" (50.8 cm) minimum above the floor.
Electrical Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher. Failure to do so can result in death or electrical shock. If the water line and the cable extend to the locations shown, proceed to the "install Drain Hose" section. If they do not reach far enough, follow the instructions in the "Prepare Cabinet Opening-New Utilities" section.
Woodcabinet: Sand holeuntilsmooth. Metalcabinet: Cover holewithgrommet included withpower supply cordkit. Option Route cable from power supply through cabinet hole (cable must extend to the right front side of cabinet opening). Tape cable to the floor in area shown. This will avoid cable from moving when dishwasher is moved into cabinet opening. B, Direct Wire: Helpful Tip: Wiring the dishwasher will be easier if you route the cable into the cabinet opening from the right side.
Slowly route watersupply linethrough holeincabinet. (ifusing copper tubing, itwillbendandkinkeasily, sobegentle.) It should befarenough intothecabinet opening toconnect itto thedishwasher inletonthefrontleftsideofthedishwasher. Route drainhose asshown through holeincabinet tothefront center ofopening wheredrainconnection willbemade. Tape drainhose tothefloorinareashown. Thiswillkeepitfrommoving whendishwasher ismoved intocabinet opening.
_ ;; _;; _ _;;_;;t;; ¸ ;;_; _;:; ?_;:_h;; ¸ _;_ _;_;_;; _ _ tit;; 1.Connect black end of of drain hose to waste tee and cut if needed. NOTE: Do not cut ribbed section. 2. Attach black end of drain hose to waste tee with a large silver drain hose clamp (provided). Use pliers to squeeze clamp open and move into position. If the drain hose was cut use a 1W' to 2" (3.8 to 5 cm) screw-type clamp (not provided). Option C, Waste disposer = with air gap 1.
P:_iii:" e{li:i:i0, s::_iiii::'_ e :iii:}, i_i_i_ii s ]ii:_ w i,;i_:_,!!_ii@_ e !i!: '_¸ Tip Over Hazard Do not use dishwasher untiJ completely installed. Do not push down on open door. Using a 1/4" hex head socket, nut driver or Phillips screwdriver, remove 2 screws attaching access panel and lower panel to dishwasher. Doing so can result in serious injury or cuts. NOTE: Do not remove tech sheet from access panel. Excessive Weight Hazard Use two or more people to move and install dishwasher.
Option A, Power Supply Cord: Using a1/4" hex-head socket, nutdriverorPhillips screwdriver, remove terminal boxcover. Retain forlateruse. Route cord so that it does not touch dishwasher motor to lower part of dishwasher tub. Pull cord through strain relief in terminal bow. Select UL Listed/CSA Approved twist-on wire connectors (not included) rated to connect your household wiring to 16-gauge dishwasher wiring. Install aULListed/CSA Approved strainrelief.
Power Cord--Connect remaining wires NOTE: Do not pre-twist stranded wire. Twist on wire connector. Gently tug on wires to be sure both are secured. 0 Connect wires black to black and white to white, using UL Listed/CSA Approved twist-on wire connectors (not included). Place wires inside terminal box. Insert tabs on left side of cover. Make sure wires are tucked inside box. Close cover ensuring wires are not pinched. Use 1/4"nut driver and previously removed screw to secure cover.
Turnbothleveler legstothesame height. Putwheels inthe required position determined from"Dishwasher Height Adjustment Chart". (Tochange wheelposition, useafiat-blade screwdriver topopoutthewheel, thensnapintothenew position.) Using twoormorepeople, stand dishwasher upright. NOTE: Donotinstall kickplate untilinstructed. Move dishwasher cabinet opening close to i i Built-up floors(Kitchen floorheight ishigher thancabinet opening.) Example: Kitchen floortiledoesnotextend into cabinet opening.
Withanother person holding thedishwasher tokeep itfrom tipping, openandclose thedoorafewtimes. Lfthedoorcloses orfallsopenunder itsownweight, thedoortension willneedto beadjusted. IMPORTANT: Ifwheels wereremoved, cover thefloorwhen moving thedishwasher. Slowly move dishwasher completely into cabinet opening. Donotkinkorpinchwaterline,drainhose, power supply cordordirectwirebetween dishwasher and cabinet. Remove cardboard fromunder dishwasher. NOTE: Itisallrightifdishwasher fitstightlyintocabinet opening.
NeJpfuJ Tip:Push uponfrontofdishwasher toraise dishwasher offtheground toadjust frontlegs. Withsome installations, it maybeeasier toadjust thefrontlegusing the3/16" hexhead socket oradjustable wrench. using copper or flexible line Copper tubing only: Put the tubing into the 90 ° elbow fitting as far as it will go (the copper tubing bends and kinks easily). Slide the nut and ferrule forward and start the nut onto the elbow threads.
NOTE: If the power proceed to "Secure Green clamp supply cord was connected earlier Dishwasher in Cabinet Opening" section. _;_[_[_#__[_[___ Option B, Direct Wire: Black drain hose connector -- Drain hose Drain hose stop Stop Place towel under drain hose to catch any water in drain hose. Place the small green drain hose clamp onto the small end of the drain hose. Push the new drain hose into the black drain hose connector up to the drain hose stop.
Electrical Electrically ground Connect ground in terminal box. death, to follow fire, Ifneeded, see website for animated representation Visit www.amana.com/electrical under FAQ tab. Hazard of this step. dishwasher. wire to green Do not use an extension Failure Shock these or electrical ground connector cord. instructions can result in shock. Tighten to secure cable. ) Ground Form bare ground wire into a U-shaped hook.
(iiiii iii ii iL:Ai:iii:i e ii:i NOTE: Do not drop screws into bottom of dishwasher. Locate brackets on top of dishwasher and secure dishwasher to countertop with two, # 10 x 1/2" Phillips-head screws (included). The dishwasher must be secured to keep it from shifting when door is opened. Check that dishwasher in cabinet is still level front to back and side to side opening. IMPORTANT: If you have solid countertops such as corrian, granite, etc., you must use side mounting kit (Part Number 8212560).
Remove towelfromdishwasher. Reinstall thelowerdishracl<. Hold thetwopanels together andplace themagainst dishwasher leg.Using aPhillips or1¼,, screwdriver, reinstall thescrews through theholes intheaccess panel andtheslotsinthelowerpanel. Ifneeded, seewebsite foranimated representation ofthisstep. Visitwww.amana.com/anchoring under FAQ tab. Check thattheloweredgeofthelowerpanel contacts thefloor. Adjustifnecessary. Check thatgrounding clipisattached tothelower panel.
[_ Read the Dishwasher dishwasher. [_ Electrical Plug into a grounded Do not remove Shock 3 prong ground Hazard dishwasher and allow it to complete the shortest wash cycle. After the first 2 minutes unlatch door, wait 5 seconds, then open door. Check to see that there is water in the bottom of the dishwasher tub. Check that dishwasher is working Do not use an adapter• Failure in death, to follow fire, these Check that all parts have been installed and no steps were skipped.
Table des rnati@res Instructions S_curit_ du lave-vaisseJJe.................................... 21 d'instaHation Pr6paration E×igences d'instaHation...................................... 22 du lave-vaisselle Outillageet pieces .......................................... 22 Raccordement Exigences d'emplacement ................................... 22 Dimensions Sp6cificationsde l'6vacuation...............................
EXIGENCES D'INSTALLATION Autres Rassembler les outils et pieces n_cessaires avant de commencer rinstallation. Lire et observer les instructions avec chacun des outils de la liste ci-dessous. fournies articles _ventuellement Bride de tuyaU Vis 1½ _2 I (38,1_ 5cm)_ (max. 3) n_cessaire ,.,: Tournevis . _ !ame Plate Couteau utilitaire Tourne-ecrou ou cl6 _ douille _hexagonale de _.
I'emplacement d'installation doltoffrir: •facilit6 d'acces acanalisation d'eau, c_blage 61ectrique et canalisation d'6gout. •facilit6 d'acces pour chargement etd@hargement delavaisselle; si I'appareil estinstall6 dans unangle, ondoltpr@oir unespace libre d'aumoins 2"(5,1cm)entre lec6t6delaporte dulave-vaisselle etle murouleplacard adjacent ousup6rieur. •ben@uerrage delacavit6, pour fonctionnement correct etaspect esth6tique. •fa,cades deplacard perpendiculaires ausol.
•Unnouveau tuyaud'6vacuation estfourniaveclelave-vaisselle; s'il n'estpassuffisamment long,utiliser untuyauneufpluslongde Iongueur maximale 12'(3,7m)(piece no3385556) conforme aux criteres detestenvigueur deAHAM/IAPMO, r6sistant alachaleur etauxd6tergents, quipeut_treconnect6 surleraccord de 1"(2,5cm)dulave-vaisselle.
INSTRUCTIONS D'INSTALLATION Risque Interrompre de choc I'alimentation _lectrique le lave-vaisselle (au niveau fusible ou disjoncteur). Le non-respect un d_c_s _D de cette ou un choc n _lectrique du tableau instruction avant d'installer de distribution peut - causer _lectrique.
0 Placard trou. en bois : Poncer pour produire Placard m6tallique : Installer cordon d'alimentation. une surface lisse dans le sur le trou le passe-ill fourni avec le Installer un cSble depuis I'alimentation _lectrique jusqu'a la cavit_ d'encastrement du lave-vaisselle, a travers le trou perc_ dans la paroi (la Iongueur du cSble doit _tre suffisante pour qu'il puisse p_n_trer dans le c6t_ avant droit de I'ouverture d'encastrement).
Faire passer prudemment lacanalisation d'alimentation travers letrouperc6 dansleplacard. (SiI'onutilise untubede cuivre, celui-ci peuts'6craser/se d6former facilement Iorsd'une flexion; proc6der prudemment.) IIfautquelaIongueur dela section quid6passe dansI'espace d'encastrement soit suffisante pourleraccordement aI'entr6e dulavewaisselle sur lec6tegauche/a I'avant dulave-vaisselle.
1. Arracher I'opercule arrachable du broyeur d6chets - utiliser un marteau et un tournevis. 2. Retirer I'opercule arrachable pince a bec effil& 3. Connecter I'extr6mit6 noire du tuyau d'6vacuation sur le brise-vide; couper n6cessaire. REMARQUE : Ne pas couper section ondul6e. 4. @ 1.Connecter I'extr6mit6 noire du tuyau d'6vacuation sur le raccord T du circuit de plomberie; couper si n6cessaire. REMARQUE : Ne pas couper dans la section ondul6e.
Risque de basculement hie pas utiliser le lave=vaisselle jusqu'a ce qu'il soit compl_tement installS. hie pas appuyer sur la porte ouverte. Utiliser une cl6 a douille hexagonale ou tourne-6crou Le non=respect de ces instructions peut causer des blessures graves ou des coupures. de 1¼,ou un tournevis Phillips; 6ter les deux vis fixant le panneau de I'ouverture d'acces et le panneau inf6rieur sur le lave-vaisselle. REMARQUE : Ne pas enlever la fiche technique coll6e sur le panneau de I'ouverture d'acces.
Utiliser untourne-6crou, unecl6adouille hexagonale de1/4" ou untournevis Phillips; d6monter lecouvercle duboftier de connexion; conserver lavisetlecouvercle pourr6utilisation. Installer le cordon d'alimentation de telle maniere qu'il ne soit pas en contact avec le moteur du lave-vaisselle, jusqu'a la partie inf6rieure de la cuve du lave-vaisselle. Introduire le cordon dans le boftier de connexion a travers le serre-cSble.
REMARQUE : Nepaspr6-torsader lesconducteurs toronn6s. Installer chaque connecteur defilssurlesconducteurs (mouvement devissage). Tirerdoucement surlesconducteurs pourv6rifier qu'ilssontsolidement connect6s. Utiliser desconnecteurs defils(homologation ULouCSA) (pas fournis) pourraccorder lesconducteurs -noiranoiretblanc blanc. C&bled'alimentation : blanc_ noir_ Conducteur de_Vis liaison&laterre Placer lesillsaI'int@ieur duboftier deconnexion. Ins6rer lespattes duc6t6gauche ducouvercle.
Roues et pieds - R_glage Tuyau Ajuster (vissage)les deux pieds de r6glage de I'aplomb a la m_me hauteur. Placer les roues a la position n6cessaire selon les indications du "Tableau de r6glage - Hauteur du lave-vaisselld'. (Pour modifier la position des roues, utiliser un tournevis a lame plate pour enlever la roue; reinstaller la roue a la nouvelle position choisie (emboftement).
Silaportesefermetroprapidement, r6duire latension des ressorts :d6placer lepointd'ancrage deI'extr6mit6 duressort versI'avant dulave-vaisselle. REMARQUE :Utiliser lem_me pointd'ancrage (encoche) pour chaque ressort (c6t6gauche etc6t6droit). IMPORTANT :Silesroues ont6t6enlev6es, prot6ger lesol durant led6placement dulave-vaisselle. Ins6rer (lentement) completement lelave-vaisselle danslacavit6 d'encastrement.
Conseil utile: Pousser surI'avant dulave-vaisselle pour soulever 16gerement lelave-vaisselle etles6parer dusolpourle r6glage despiedsavant. Dans certaines configurations d'installation, ilpeut_treplusfacile d'utiliser unecl6adouille hexagonale de3A6" ouunecle_molette pourler6glage des pieds avant.
1_ Raccordement du tuyau d'_vacuation REMARQUE : Si un cordon d'alimentation a 6t6 connect6 pr6c6demment, passer a la section Immobilisation vaisselle dans la cavit_ d'encastrement. Bride verte Connecteur noir du tuyau d'_vacuation du lave- Tuyau d'_vacuation Butte du tuyau d'_vacuation Butte Placer une serviette sous le tuyau d'6vacuation pour r6cup6rer toute quantit6 d'eau qui peut s'6couler du tuyau.
Configuration C_ble de c bl d'a imentation : conducteur de_ liaison _ la terre Risque Retier le lave=vaisselle a la terre d'une methode Si n6cessaire, Brancher la terre le fJl relic dans la boite Ne pas utilJser Le non=respect d_ces, a la terre au connecteur le le site Internet (onglet FAQ) qui vid6o de cette 6tape. de la borne. un cable de rallonge. de ces instructions un incendie vert relic consulter www.amana.
REMARQUE :Veiller anepaslaisser tomber unevisaufonddu lave-vaisselle. Identifier lesbrides d'arrimage ausommet dulave-vaisselle; fixer lesbrides surleplandetravail avecdeux visPhillips n° 10x V2" (fournies). II faut que le lave-vaisselle puisse osciller/basculer soit immobilis6 Iors de rouverture pour qu'il ne de la porte. V6rifier raplomb vertical etraplomb transversal dulavevaisselle install6 danslacavit& IMPORTANT :Sileplandetravail estfaitd'unmat6riau comme leCorrian, legranit, etc.
Retirer laserviette deprotection quiavait6t6plac6e aufonddu lave-vaisselle. R6installer lepanier inf6rieur. Maintenir lesdeux panneaux ensemble; placer lesdeux panneaux contre lepieddulave-vaisselle. Utiliser untournevis Phillips ouun tournevis 1¼,, pour r6installer lesvisatravers lestrousdupanneau de I'ouverture d'acces etdupanneau deplinthe. Sin6cessaire, consulter lesiteInternet www.amana.com/anchoring (onglet FAQ) quipr6sente une description vid6odecette6tape.
[_1Lire attentivement avec I'appareil. le mode d'emploi du lave-vaisselle fourni [_ V&rifier que tousles composants ont &t_ install&s et qu'aucune _tape n'a _t_ omise. V_rifier la presence de tous les outils. Risque de choc _iectrique Brancher sur une prise a 3 alveoles reliee a ia terre. Ne pas enlever la broche de liaison a la terre. Ne pas utitiser [_1Mettre le lave-vaisselle en marche; laisser I'appareil ex_cuter le programme de lavage le plus court.
W10261420A © 2009 All rights reserved. Tous droits reserves. @Registered TrademarWTMTrademark of Maytag Used under license by Maytag @Marque d@osee/TMMarque de commerce de Maytag Emploi sous licence par Maytag Corporation or its related companies. Limited in Canada. Corporation ou de ses compagnies affili_es. Limited au Canada. 7/09 Printed in U.S.A Imprime aux E.-U.
