Installation Guide

ManualsBrandsAmerican Standard ManualsBathColony Soft 4 in. Centerset 2-Handle Low-Arc Bathroom Faucet in Polished Chrome with Speed Connect Drain

COLONY SOFT

2275.409

2275.509

Insert FAUCET (1) and CABLE CONNECTOR (2) through center hole

of mounting surface. Fig. A.

From under side of mounting surface thread the two MOUNTING

NUTS (3) onto FAUCET SHANKS (4). Fig. B.

Center FAUCET (1) and hand tighten MOUNTING NUTS (3) to

secure FAUCET (1).

Certiﬁed to comply with ANSI A112.18.1

Installation

Instructions

Centerset Lavatory Faucet

with Speed Connect™ Drain

INSTALL FAUCET

Adjustable Wrench Screwdriver Channel Locks

Recommended tools

Tubing Cutter

Congratulations on purchasing your American Standard faucet

with the Speed Connect drain, a feature found only on

American Standard faucets.

*Your new American Standard faucet is designed to work only with

the Speed Connect drain.

To ensure that your installation proceeds smoothly-please read these

instructions carefully before you begin.

Fig. A.

Fig. B.

M968876 Rev. 1.2

Plumbers' Putty or Caulking

(HAND TIGHTEN)

Speed Connect Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the ﬁrst time, every time.

Apply a bead of putty along the edge of the underside of the FAUCET (1).

PUTTY

Summary of content (6 pages)

PAGE 1
C COLONY SOFT Centerset Lavatory Faucet with Speed Connect™ Drain H Installation Instructions 2275.409 2275.509 Congratulations on purchasing your American Standard faucet with the Speed Connect drain, a feature found only on American Standard faucets. Speed Connect Drain* • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time. *Your new American Standard faucet is designed to work only with the Speed Connect drain.
PAGE 2
POP-UP DRAIN Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 3 DRAIN BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 3 4 REMOVE FLANGE Fig. A. 1 Thread FLANGE (1) counter-clockwise and remove Fig. B. FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 3
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 1-1/4” O.D. 8 CHECK OPERATION OF POP-UP Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. 1 Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.
PAGE 4
10 TEST INSTALLED FITTING 1 5 With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Ensure that AERATOR (3) is tightened completely. 3 Operate HANDLES (1) to allow water flow. CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in SINK. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting section in these instructions.
PAGE 5
Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 6
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front.