Installation Guide

INSTALLATION INSTRUCTIONS
791033-100 Rev. M
AMERICAST BRAND
ENGINEERED MATERIAL
CAMBRIDGE
®
2460 SERIES/2461 SERIES WHIRLPOOL / BATHING POOL
FOR AFTER-SALES SERVICE CALL 1 [phone] WEEKDAYS.
THANK YOU...
for selecting an American Standard bath. Your new
bath is shipped to you after careful inspection. The
whirlpool version is completely assembled with pump,
motor, and system piping. All you need to finish the
installation are your selected fittings and electrical
connections for a whirlpool.
To insure maximum performance and pleasure from
this product, please follow the instructions and
cautions.
GENERAL INSTALLATION INFORMATION
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your
vendor immediately.
After inspection and during installation, protect the bath from construction damage. After installation, and before
enclosing with wallboard, tile, etc., water test the unit and check for leaks.
Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely
affect the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by
the pump, motor, or piping system.
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and
enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead
(required for recess installations).
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.
WARNING! Do not lift whirlpool by the piping harness at any time.
List of Optional Components (not included):
• Safe-T-Heater 9075.120*
* see your American Standard Distributor
List of Required Components (not included):
• Drain 1583.470*
• Bath Filler*
* see your American Standard Distributor
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 4
Stringers
• Drop Cloth
• 15 amp GFCI
Outlet
• Cement, Plaster,
Grout
GENERAL SPECIFICATIONS FOR 2460/2461 WHIRLPOOL
WHIRLPOOL ELECTRICAL SPECIFICATIONS 2460/2461.028 & .128
SYSTEM I PUMP 1.4 HPR, 7.5 AMPS,120V.
SAFETY HEATER 12 AMPS,120V.
60 x 32 x 17-3/4 In. (1524 x 813 x 451mm)
142 Lbs. (64 Kg.)
559 Lbs. (254 Kg.)
50 Gal. (190 L)
39 Gal. (148 L)
41 x 20 In. (1041 x 508mm)
54 x 26 In. (1372 x 660mm)
12-5/8 In. (321mm)
41 Lbs./Sq.Ft. (200 Kgs./Sq.m)
13.9
30.9
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
1-1/2" N.P.T. THREADS
1-1/2" O.D. TAILPIECE
117mm
(4-5/8)
ROUGH
FLOOR
3/4"
(19mm)
PUMP
PROVIDE ACCESS TO PUMP FOR SERVICING ON ALL INSTALLATIONS
ON / OFF
SWITCH
SAFE-T-HEATER
REMOVABLE BLANK
60"
(1524mm)
32"
(813mm)
16"
(406mm)
FINISHED
WALL
1"
(25mm)
9" X 12"
(229 X 305mm)
FLOOR
CUTOUT
2-3/4"
(70mm)
17-3/4"
(451mm)
17-3/8"
(441mm)
2-3/4"
(70mm)
3"
(76mm)
8"
(203mm)
2-1/2"
(64mm)
15/16"
(24mm)
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2013