Installation Guide

ManualsBrandsAmerican Standard ManualsBathMoments Selectronic Plug-In AC Powered Touchless Lavatory Faucet in Polished Chrome

M965653 Rev. 1.4 (10/15)

CAUTION: Use only American Standard

supplied cable sets. Using non-AS supplied

cables, or cutting, splicing or modifying any

components will void the warranty.

Installation Instructions

Certified to comply with ASME A112.18.1

NOTE TO INSTALLER: Please give this manual to the customer after installation.NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic

Products visit our website at: www.americanstandard-us.com

or e-mail us at: CRTTEAM@americanstandard.com

For Parts, Service, Warranty or other Assistance,

please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-306-1093)

SELECTRONIC

Moments

Proximity Faucets

Product No.'s & Options

Specifications

Faucet Installation

Electrical Installation

Start-up / Maintenance

FAQ’s / Troubleshooting

Parts

2-3

4-6

7-8

8-9

MODEL NUMBERS

2506.1X2 2506.1X3 2506.1X5

Summary of content (10 pages)

PAGE 1
Installation Instructions SELECTRONIC® Moments Proximity Faucets MODEL NUMBERS 2506.1X2 2506.1X3 2506.1X5 CAUTION: Use only American Standard supplied cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty. © 2007 American Standard Product No.'s & Options 1 Specifications 2 Faucet Installation 2-3 Electrical Installation 4-6 Start-up / Maintenance 7-8 FAQ’s / Troubleshooting 8-9 Parts 10 Certified to comply with ASME A112.18.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. All American Standard Faucets Are Water Tested At Our Factory. Some Residual Water May Remain In The Faucet During Shipping. UNPACKING The illustration below shows the fitting and all loose items after they have been removed from the carton. Some items may be packaged partially assembled to other items.
PAGE 3
Roughing-in Dimensions Fig. 1 GENERAL DESCRIPTION: FINISHED WALL Electronic faucet with proximity operation. Vandal resistant solid brass construction single post mounting. Operates on DC (battery/power pack) or AC permanent power (plug-in/hardwire). In-line strainer for solenoid is integral. Single inlet 3/8 compression, built-in check valves, and flexible stainless steel 16-1/4" reach inlet hose for spout connection. 154mm (6-1/16) 126mm (5) 159mm (6-1/4) 55.
PAGE 4
2 MOUNT CONTROL BOX; Fig. 2 Fig. 2 LAVATORY RIM OR MOUNTING SURFACE 1. Determine location of CONTROL BOX (1). It must be located with-in the 14" (356mm) by 21" (533mm) shaded area shown in Figure 2 in order for electrical connections from the spout assembly to be made. 14" (356mm) NOTE: CONTROL BOX SUPPLY HOSE is 20". Distance between wall supply and CONTROL BOX (1) must be taken into consideration. SUPPLIES ENCLOSURE MOUNTING HOLES 1 2-3/4" (71mm) 2.
PAGE 5
ELECTRICAL INSTALLATION Product Fig. 1 1 Page DC Long Life Power Pack (6053.193) 4 DC Standard Battery (6055.193) 4 AC Plug-in (6056.193) 5 AC Hardwire (6059.193) 5 AC Multi Hook-up (6057.193) 6 Fig. 1a 2 Fig. 1b 3 5a 5 INSTALL BATTERY A DC VERSIONS (LONG LIFE POWER 4 PACK & STANDARD BATTERY); Fig. 1 1. Remove CONTROL BOX COVER (1). Fig. 1. -P2 CR Fig. 1c STANDARD BATTERY 6 2. Feed the 27" EXTENSION CABLES (2) through the top of CONTROL BOX (3). Fig. 1a.
PAGE 6
B AC VERSIONS (HARDWIRE / PLUG-IN); Fig. 2 Fig. 2 CAUTION 2 Disconnect AC power supply before opening CONTROL BOX. 3 1 NOTE: For AC installation, make power supply connection before mounting CONTROL BOX (3) to wall. 1. Remove CONTROL BOX COVER (1). Feed the EXTENSION CABLES (2) from the Faucet through the top of CONTROL BOX (3). Fig. 2. FOR PLUG-IN HOOKUP ONLY 2a. Insert POWER CORD (8) through POWER SUPPLY GROMMET (9) Fig. 2a. 3a. Insert POWER CORD (8) through side GROMMET (6) as shown. Fig. 2a.
PAGE 7
Fig. 3 Unit #2 Unit #1 Unit #3 Already installed 10 ft. EXTENSION CABLE AC HARDWIRE POWER SUPPLY AC POWER SUPPLY OR *MAXIMUM OF 15 UNITS PER AC POWER SUPPLY. 10' MAXIMUM CABLE LENGTH BETWEEN UNITS. C MULTI-AC VERSION (DAISY-CHAIN); Fig. 3, 3a Important: All control box covers must be removed before beginning to make daisy-chain connections. Disconnect the first unit’s Y-Adapter from power supply before making daisy-chain connections.
PAGE 8
MAINTENANCE Fig. 1 DETECTION ZONE A HAND WASH SENSOR OPERATION; Fig. 1 When the Sensor detects a user, the water immediately starts to flow. Water flow will stop 2 seconds after user is out of sensor range. The off delay allows the user to comfortably move his hands without the flow cycling on and off. As a precaution, a safety timer will turn off the water, after the sensor has been blocked for 59 seconds. The water will stay off until the blockage is removed from the detection zone.
PAGE 9
LONG LIFE POWER PACK; Fig. 4 Fig. 4 1. Remove COVER from CONTROL BOX (1). CR-P2 D INSTALL / REPLACE THE BATTERY or 1 5 2 STANDARD BATTERY 2. Disconnect BATTERY HOLDER (3) from 27" EXTENSION CABLE (5). 6 3 3. Remove old BATTERY from BATTERY HOLDER (3). Install new BATTERY (2) making sure the terminal side is inserted first and shape of the battery follows the shape of the BATTERY HOLDER (3). LONG LIFE POWER PACK 4. To replace LONG LIFE POWER PACK (4), unplug and replace with new Power Pack. 5.
PAGE 10
TROUBLESHOOTING FLOW CHARTS UNIT DOES NOT FUNCTION ARE EXTERNAL SUPPLY STOPS OPEN? NO OPEN EXTERNAL SUPPLY STOPS. NO OPEN INTERNAL SUPPLY STOP. (HEX KEY NEEDED) YES CRITICALLY LOW BATTERY. INSTALL NEW BATTERY. YES IS INTERNAL SUPPLY STOP OPEN? YES REPEATED DOUBLE FLASH ON SENSOR? NO 1 RECONNECT BATTERY TO SENSOR. DOES SENSOR FLASH FOR 5 SECONDS? 2 NO NO 1 2 DEAD BATTERY. INSTALL NEW BATTERY. REPEAT. CHECK FOR DAMAGE TO SENSOR WIRE INSULATION. REPLACE SENSOR.