Installation Guide

SAVE FOR FUTURE USE
7301816-100 Rev. B
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2013
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure
Hacksaw Gasket Flexible Supply Tube Closet Bolts Carpenters Level
CAUTION: PRODUCT IS FRAGILE. TWO PEOPLE ARE RECOMMENDED FOR HANDLING
TO AVOID BREAKAGE AND POSSIBLE INJURY!
NOTE: Pictures may not exactly define contour of china and components.
NOTE: For proper operation these products require a minimum of 30 psi line pressure.
NEOLO FLOOR MOUNT BACK OUTLET
FLUSHOMETER TOILET
INSTALLATION INSTRUCTIONS
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be
sure your installation conforms to local codes.
!
Models 2529.116, 2530.116, 2531.116
NEOPRENE
SEAL
SEALANT
INSTALL NEOPRENE OR GRAPHITE FELT SEAL*
Install seal evenly around waste flange (horn).
Apply a thin bead of sealant around base flange.
*NOTE: Wax seal not recommended for this application.
FLUSH TO
1/16" (1.6mm)
EXPOSED
CLOSET
FLANGE
CLOSET
BOLTS
152mm
(6")
PILOT
HOLES
108mm
(4-1/4")
*
Install closet bolts in flange channel, turn
90°, and slide into place 6" (152 mm)
apart and parallel to floor. (Use putty to
hold bolts in place if necessary.) Brace
under flooring as needed and drill two
mounting pilot holes as shown.
INSTALL CLOSET BOLTS
1 REMOVE OLD TOILET
a. Close flush valve completely.
b. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug wall waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and perpendicular to the floor before new toilet is installed!
3
2
ROUGHING-IN DIMENSIONS NOTE: Distance from wall to closet flange centerline must be as listed below:
4
NEOLO 2529 TOP SPUD NEOLO 2530/2531 BACK SPUD
FINISHED WALL
FINISHED
FLOOR
267mm
(10-1/2")
76mm
(3")
108mm
(4-1/4")
108mm
(4-1/4")
632mm
(24-7/8")
476mm
(18-3/4")
356mm
(14")
C/L OF
OUTLET
352mm
(13-7/8")
222mm
(8-3/4")
152mm
(6")
19mm(3/4")
C/L OF SEAT POST HOLE
140mm (5-1/2") CENTERS
660mm
(26")
C/L OF 1/2" DIA. BOLT
HOLES ON 140mm (5-1/2) CENTERS
38mm (1-1/2") SPUD
108mm - 134mm
(4-1/4" - 5-1/4")
25mm (1") N.P.T. OR C.W.T.
SUPPLY TO FLUSH VALVE
FINISHED WALL
38mm
(1-1/2")
SPUD
70mm
(2-3/4")
DIA. HOLE
IN WALL
FINISHED
FLOOR
356mm
(14")
222mm
(8-3/4")
152mm
(6")
257mm
(10-1/8")
108mm
(4-1/4")
216mm
(8-1/2")
632mm
(24-7/8")
479mm
(18-7/8")
356mm
(14")
C/L OF
OUTLET
20mm
(3/4")
108mm
(4-1/4")
C/L OF SEAT POST HOLE
140mm (5-1/2") CENTERS
C/L OF 13mm (1/2") DIA. BOLT
HOLES ON 140mm (5-1/2") CENTERS
394mm
(15-1/2")
*
2529 = 267mm (10-1/2")
2530/2531 = 257mm (10-1/8")