Installation Guide

HEX WENCH, SUPPLIED
8
9
HANDSHOWER INSTALLATION (Model 2555.921 series only)
TEST INSTALLED FAUCET
6
Turn VALVES "off" and attach handles.
Lift HANDSHOWER from HOLDER, direct spray into tub, lift
TRANSFER KNOB to check HANDSHOWER and HOSES for leaks.
Turn handles "off."
Drop SPRAY ESCUTCHEON (1) through the fourth hole of the tub ledge (12" max from
SPOUT center) with SPRAY ESCUTCHEON (1) directed towards tub center. Be sure RUBBER
RING (2) is properly seated in ESCUTCHEON (1). Install RUBBER WASHER (3) BRASS WASHER (4)
and LOCKNUT from underside of ledge.
Secure SPRAY ESCUTCHEON (1) by tightening LOCKNUT.
Add SEAL WASHER (5) and connect HOSE (10) to outlet nipple
at the bottom of COUPLING (7). Tighten firmly.
Slip SHOWER HOSE (8) with COUPLING NUT through SPRAY
ESCUTCHEON (1). Install SEAL (9) and connect both HOSES (8)
and (10), Connect HAND SHOWER (11) to SPRAY HOSE (8).
When not in use, HANDSHOWER should be seated
in the HOLDER.
NOTE
Before the bathroom is completely finished, you may
want to remove spout, handshower, and handles.
To remove handles, reverse steps in section 4.
To remove SPOUT (1), proceed as follows:
Lift TRANSFER ROD (2) and unscrew KNOB (3). (Model 2555.921only).
Remove PLUG BUTTON (4) and remove SET SCREW (5) using 5mm hex
wrench supplied.
Lift SPOUT (1) off SHANK (6) carefully and remove RUBBER RING (7).
Unscrew SHANK SLEEVE (8) and lift TRANSFER ROD (2) from
SHANK (6). (Model 2555.921 only).
Reverse sequence to re-install SPOUT (1). Be sure RUBBER
RING (7) is properly seated in its recess at the base of the SPOUT (1).
Make certain SET SCREW (5) is properly aligned and tight so that
SPOUT (1) is locked in place.
7
5
With handles in "off" position, turn on water supplies and check
all connections for leaks.
Operate both handles and flush water lines thoroughly.
Check SPOUT mounting for leaks.
The flow rate of this Tub Filler exceeds 20 gallons/minute
at higher water pressure. Do not fill bathtub unattended.
CAUTION
1
2
3
4
5
5
7
8
10
9
1
2
3
4
6
7
6
8
DO: SIMPLY RINSE THE PRODUCT
CLEAN WITH CLEAR WATER.DRY
WITH A SOFT COTTON FLANNEL
CLOTH.
DO NOT: DO NOT CLEAN THE
PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH
CLEANERS, OR A CLOTH WITH
A COARSE SURFACE.
CARE INSTRUCTIONS:
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2011
HOT LINE FOR HELP
M 9 6 5 111 R E V. 1. 1
11
SERVICE
2
90˚
If spout drips, operate handles several times from
OFF to ON position. Do not force - handles turn
only 90˚.
6
4
3
5
7
1
Turn valve to OFF position
Remove SET SCREW (7) with 5/64" Hex Wrench.
Pull HANDLE (1) “UP” firmly to
release from ADAPTER (3).
Pull HANDLE BASE (6) off DECK ADAPTER (2).
Remove SPRING CLIP (4). Lift STOP WASHER (5),
turn 90˚ and replace. Replace SPRING CLIP (4).
Re-install HANDLE ASSEMBLY.
To change direction of handle:
5/64" HEX
WRENCH
9
LOCKNUT