Installation Instructions

ManualsBrandsAmerican Standard ManualsBathtubs2770.018WC.020

THANK YOU...

for selecting an American Standard bath. Your new bath is

shipped to you after careful inspection. The whirlpool version

is completely assembled with pump, motor, and system

piping. All you need to finish the installation are your

selected fittings and electrical connections for a whirlpool.

To insure maximum performance and pleasure from this

product, please follow the instructions and cautions.

GENERAL INSTALLATION INFORMATION

Carefully uncrate and inspect your new bath for any shipping

damage. If such damage is found, report it to your vendor

immediately.

After inspection and during installation, protect the bath from

construction damage. After installation, and before enclosing

with wallboard, tile, etc., water test the unit and check for

leaks.

If a whirlpool, do not make modifications to the whirlpool

system or remove pump from factory mounting. This could

adversely affect the safety and performance of the whirlpool

and void the warranty. Do not handle or move the whirlpool

by the pump, motor, or piping system.

Fittings (bath filler, shower arm, etc.) are not provided with

the bath and must be ordered separately. Framing and

enclosing materials are provided by others. Check for

availability of optional American Standard wall tiling bead

(required for recess installations).

Protect all finished surfaces of the whirlpool during

construction and installation using a drop cloth.

WARNING! Do not lift whirlpool by the piping harness at

any time.

NOTE: Deck-mounted fittings are not recommended.

752481-100 Rev. K

All product names listed herein are trademarks

of American Standard Inc. unless otherwise noted.

List of Optional Components (not included):

• Safe T-Heater 9075.120*

• Tile Bead Kit 751755-100*

• Apron Kit*

* see your American Standard Distributor

List of Required Components (not included):

• Drain 1583.470* • Bath Filler*

* see your American Standard Distributor

List of Required Tools and Supplies:

Tools

• Level

• Tape Measure

• Pipe Wrench

• Slip Joint Pliers

• Screw Driver

• Standard

Woodworking Tools

• Personal Safety

Equipment

• Caulking Gun

Supplies

• Nails

• Putty

• Caulking (waterproof)

• 1 x 3 or 2 x 2

Stringers

• Drop Cloth

• 15 amp GFI

Outlet

• Cement, Plaster,

Grout

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

INTEGRAL

SUPPORT

FEET

LEVELING

STRINGER

NOT FOR

SUPPORT

ROUGH

FLOOR

2-3/4"

(70mm)

C/L OF

OVERFLOW

C/L OF

SPOUT

C/L OF

VALVES

C/L OF

SHOWER ARM

59-7/8"

(1521mm)

31-3/4"

(806mm)

OUTLINE OF CUTOUT

58-3/8" X 30-1/4"

(1483 x 768mm)

15-7/8"

(403mm)

8-3/4"

(222mm)

2-3/8"

(60mm)

(8) JETS

CUTOUT IN FLOOR

FOR DRAIN

PUMP

FINISHED

WALL

3/4"

(19mm)

9" (229mm)

C/L OF

SUPPLIES

C/L OF DRAIN

SEE FITTING

SPECS FOR

DIMENSIONS

(2) AIR VALVES

ON/OFF

SWITCH

PROVIDE ACCESS TO PUMP FOR

SERVICING ON ALL INSTALLATIONS

18-1/4"

(464mm)

1-1/2"

(38mm)

19-3/4"

(502mm)

1-1/2" O.D.TAILPIECE

12"

(305mm)

12"

(305mm)

OPTIONAL TO

FINISHED FLOOR

USUALLY BETWEEN

65" & 78"

(1651 & 1981mm )

(102mm)

2-3/4"

(70mm)

4-5/8"

(117mm)

1-1/2" N.P.T.M.

THREADS

SAFE-T-HEATER

REMOVABLE

BLANK

INSTALLATION INSTRUCTIONS

HIGH GLOSS ACRYLIC

SHOWN LESS ALL FITTINGS

CADET™ 5' x 32"

WHIRLPOOL/BATHING POOL

2770.XXXW SERIES

59-7/8 x 31-3/4 x 19-3/4 In. (1521 x 806 x 502mm)

85 Lbs. (39 Kg.)

535 Lbs. (243 Kg.)

54 Gal. (204 L.)

49 Gal. (186 L.)

20 x 40 In. (508mm x 1016mm)

53-1/2 x 26 In. (1359mm x 699mm)

14 In. (356mm)

41 Lbs./Sq. Ft. (197 Kgs/Sq. m.)

15.6

29.6

GENERAL SPECIFICATIONS FOR 2770 WHIRLPOOL

INSTALLED SIZE

WEIGHT

WEIGHT w/WATER

GAL. TO OVERFLOW

MIN. OPERATING GAL.

BATHING WELL AT SUMP

BATHING WELL AT RIM

WATER DEPTH TO OVERFLOW

FLOOR LOADING

(PROJECTED AREA)

PTS.

CUBE (FT

)

WHIRLPOOL ELECTRICAL SPECIFICATIONS

1.25 HP, 9.9 AMPS, 120V.SYSTEM I PUMP

Summary of content (4 pages)

PAGE 1
2770.XXXW SERIES WHIRLPOOL/BATHING POOL INSTALLATION INSTRUCTIONS CADET™ 5' x 32" HIGH GLOSS ACRYLIC SHOWN LESS ALL FITTINGS 8-3/4" (222mm) THANK YOU... PROVIDE ACCESS TO PUMP FOR SERVICING ON ALL INSTALLATIONS 59-7/8" (1521mm) 12" (305mm) for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The whirlpool version is completely assembled with pump, motor, and system piping.
PAGE 2
INSTALLATION AND FRAMING INSTRUCTIONS The variety of installations possible for this whirlpool may require framing procedures other than those shown. Locate studs as required. Ensure roughing-in dimensions are proper, plumb and square. Provisions must be made in all installations for an access opening for servicing the pump and controls. It is strongly recommended that an additional opening be provided for access to the drain components. NOTE: The apron should not be used as the primary access opening. 1.
PAGE 3
ELECTRICAL INSTALLATION INSTRUCTIONS All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes. WARNING: When using electrical products, basic precautions should always be observed, including the following: 1. DANGER: RISK OF ELECTRIC SHOCK Connect only to a circuit protected by a ground-fault circuit interrupter. 2. Grounding is required. The unit should be installed by a licensed electrician and grounded. 3.
PAGE 4
WIRE SELECTION GUIDE Maximum distance from fusebox to motor 50' Motor High Performance 1.1 10 0' 150' 20 0' 115V Power Line 12 12 10 8 The siz es shown on this char t are recommendations for copper conductors only. Always follow local and national electrical codes DRAIN CONNECTION AND SYSTEM TEST Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the pump couplings and make sure they are hand-tight.