INSTALLATION & OPERATION GUIDE FOR EVERCLEAN® / EVOLUTION® WHIRLPOOLS AND BATHTUBS MODEL 2422L / V 5' x 32" MODEL 6060LC / VC / LCE CORNER MODEL 2771L / V 5' x 36" MODEL 2645L / V OVAL MODEL 7236L / V 6' x 36" MODEL 2425L / V - LHO 5' x 32" IA-LHO MODEL 2425L / V - RHO 5' x 32" IA-RHO MODEL 2908L REMINISCENCE® MODEL 2711L ELLISSE® MODEL 2773L CADET® 6' x 36" MODEL 2774L CADET® 6' x 42" MODEL 2775L CADET® CORNER MODEL 2732L 5' x 32" THANK YOU...
TABLE OF CONTENTS: Safety Instructions...............................................................................Page 3 General Information.............................................................................Page 4 Optional Components..........................................................................Page 4 Specifications......................................................................................Page 5 Roughing-in Reference.....................................................
IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS READ AND FOLLOW ALL INSTRUCTIONS! ! WARNING: Risk of personal injury. Do not permit children to use this unit without adult supervision. ! WARNING: Risk of personal injury. Do not operate this unit without the guard over the suction fitting. ! WARNING: Risk of electric shock. Do not permit electrical appliances (hair dryer, telephone, radio, etc.) within 60 inches (1524mm) of this unit.
General Installation Information Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor immediately. After inspection and during installation, protect the bath from construction damage. Before installation, and before enclosing with wallboard, tile, etc.
SPECIFICATIONS: L W J H SIDE VIEW C A END VIEW B DRAIN / OVERFLOW GENERAL SPECIFICATIONS FOR EVERCLEAN / EVOLUTION WHIRLPOOLS AND BATH TUBS Description Dimensions L-W-H 6060LC / VC / L 1949mm (76-3/4") LCE Corner* W 1661mm (65-3/8") H 546mm (21-1/2") Drain / Overflow Height to Underside of Deck: C Cut Out Pier GxF Rough-In Recess ExD A 18" (457mm) B 13-3/4" (349mm) C 19-1/2" (495mm) Template Provided Template 751627-400 Tub Edge to Centerline Overflow: J Weight with Water / Floor Loadi
ROUGHING-IN REFERENCES 5' x 32" (MODEL 2422L / V) 60" (1524mm) 13-3/4" 3" (349mm) (76mm) 9" (229mm) CUT OUT IN FLOOR FOR DRAIN PROVIDE ACCESS TO PUMP FOR SERVICING ON ALL INSTALLATIONS 32" (813mm) 7-3/4" (197mm) C/L OF DRAIN OUTLET 11" (279mm) 3-1/4" (83mm) 6' x 36" (MODEL 7236L / V) 72" (1829mm) 3" (76mm) C/L OF DRAIN OUTLET 7-3/4" (197mm) CUT OUT IN FLOOR FOR DRAIN 5' x 36" (MODEL 2771L / V) 60" (1524mm) C/L OF DRAIN OUTLET 11" (279mm) 3-1/4" (83mm) CUT OUT IN FLOOR FOR DRAIN 3" (76mm) 9
ROUGHING-IN REFERENCES OVAL (MODEL 2645L / V) 66" (1676mm) 11-1/4" (286mm) 1-3/4" (44mm) 18" (457mm) 36" (914mm) 9" (229mm) CUT OUT IN FLOOR FOR DRAIN PROVIDE ACCESS TO PUMP FOR SERVICING ON ALL INSTALLATIONS 3" (76mm) 5-3/8" (137mm) C/L OF DRAIN OUTLET 8-1/4" (210mm) 5' x 32" IA-RHO (MODEL 2425L/V-RHO) - shown 5' x 32" IA-LHO (MODEL 2425L/V-LHO) 60" (1524mm) C/L OF DRAIN OUTLET 3" (76mm) 10-1/2" (267mm) 7-1/2" (191mm) 2-7/8" (73mm) 16" (406mm) 9" (229mm) PUMP 32" (813mm) CUT OUT IN FLOOR F
ROUGHING-IN REFERENCES CADET CORNER (MODEL 2775L) ( " m) 60 4m 2 5 1 42-1/2" (1080mm) 9" X 12" (229 X 305mm) CUTOUT IN FLOOR FOR DRAIN 42-3/8" (1076mm) 60" (1524mm) 6-1/2" (165mm) 2-3/4" REF.
ROUGHING-IN REFERENCES CADET 6' x 42" (MODEL 2774L) 72" (1829mm) 12" (305mm) FINISHED WALL PROVIDE ACCESS TO PUMP FOR SERVICING ON ALL INSTALLATIONS 9" (229mm) 42" (1067mm) PUMP CUTOUT IN FLOOR FOR DRAIN 21" (533mm) 2-1/4" (57mm) (2) AIR VALVES (8) JETS C/L OF DRAIN OUTLET CADET 6' x 36" (MODEL 2773L) 9" (229mm) 72" (1829mm) 12" (305mm) 3/4" (19mm) FINISHED WALL 35-3/4" (908mm) 9" (229mm) CUTOUT IN FLOOR FOR DRAIN 17-7/8" (454mm) (2) AIR VALVES 2-1/4" (57mm) 5' x 32" (MODEL 2732L) PUMP
INSTALLATION AND FRAMING INSTRUCTIONS The variety of installations possible for this whirlpool may require framing procedures other than those shown. Locate studs as needed. Ensure roughing-in dimensions are proper, plumb and square. Provisions must be made in all installations for an access opening for servicing the pump and controls. It is strongly recommended that an additional opening be provided for access to the drain components. The apron should not be used as the primary access opening. 1.
TYPICAL FLANGE MOUNTING DETAIL SUGGESTED WHIRLPOOL / BATH INSTALLATION METHOD WOOD STUDS TYPICAL INSTALLATION CORNER STUD WATERPROOF DRYWALL OR CEMENT BOARD TILE ROOFING NAIL SEALANT TUB 19-1/2 (495mm) 1 x 3 (25 x 76mm) WOOD STRINGER FULL LENGTH STEEL STUDS STEEL STUD WATERPROOF DRYWALL OR CEMENT BOARD WHIRLPOOL ACCESS PANEL WASHER TILE SEALANT TUB * SEE CUTOUT TEMPLATE PROVIDED 4" (102mm) DRYWALL SCREW 1 x 3 (25 x 76mm) WOOD STRINGER FULL LENGTH UNLESS AN ACCESS OPENING OF AT LEAST 12" x 2
WHIRLPOOL ELECTRICAL INSTALLATION INSTRUCTIONS All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes. ! WARNING: When using electrical products, basic precautions should always be observed, including the following: 1. DANGER: RISK OF ELECTRIC SHOCK! Connect only to a circuit protected by a ground-fault circuit interrupter. 2. Grounding is required. The unit should be installed by a licensed electrician and grounded. 3.
For 6060LC/VC Corner Only OPERATION Fig. 1 WARNING: Prior to operation, review the Important Safety Instructions listed at the beginning of this instruction manual. Once the heater is installed and the whirlpool pump is operating, the heater is totally automatic. The heater will help maintain the temperature of the water in the bath. E-Z INSTALL™ HEATER WHIRLPOOL HEATER “ON” LIGHT Pressure Switch FACTORY INSTALLED - NOT FOR RESALE The heater is equipped with a preset pressure switch.
OPERATION: NOTE: Each whirlpool is shipped from the factory with an air actuator on/off switch and pump with attached power supply cord. OPERATING THE SYSTEM WITHOUT WATER (DRY RUNNING) WILL CAUSE PUMP DAMAGE AND VOID THE WARRANTY. Always fill the whirlpool before operating the pump. The air switch is mounted either on the deck or side wall of the tub. 1. Fill the Whirlpool: Water level must be at least one inch (25mm) above the highest jet for proper operation. (See diagram below.
Adjustable Flow Clean Jet™: The water flow action may be adjusted from vigorous to soft by rotating the nozzle clockwise for vigorous massage and counter-clockwise for soft massage. NOTE: You may balance the air volume control and nozzle adjustment for the most desirable condition.
DRAIN CONNECTION AND SYSTEM TEST Using recommended drain assembly, connect whirlpool drain to waste line in accordance with the drain assembly instructions. Tighten all drain joints securely. Check the pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of the highest jet. Recheck the pump couplings and make certain that they are not leaking.
AS AMERICA, INC. (AMERICAN STANDARD) LIMITED LIFETIME WARRANTY FOR EVERCLEAN® / EVOLUTION® ACRYLIC WHIRLPOOLS AS America (“American Standard”) warrants to the original consumer purchaser that it will, at its option, repair or replace this whirlpool or any of its parts that are found by American Standard, in its sole judgment, to be defective under normal residential use and maintenance so long as it is owned by the original consumer purchaser.
