Installation Guide

7301416-100 Rev. G
12
- 3 -
CARE AND CLEANING
When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid
detergents, disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on
your toilet seat. Some bathroom chemicals and cosmetics may damage the seat's finish.
WARNING: Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in
the tank. This damage can cause leakage and property damage.
American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners
containing chlorine (calcium hypochlorite).
FLUSH BUTTONS ON TANK
Pressing both buttons at once will flush the small flush amount 0.9 gal/flush or 3.4 L/flush. The Small Flush Button (with 3 dots)
should line up over the blue actuator on the flush tower in the tank. The Large Flush Button (with 9 dots) should line up over
the white actuator on the flush tower in the tank.
!
10 11
Turn on water supply.
Submerge the FLOAT CUP
under the water for 30
seconds. Adjust the water to
desired level by turning
WATER LEVEL ADJUSTMENT
ROD and moving FLOAT CUP
up or down.
VALVE
BODY
ADJUSTABLE
HEIGHT
WATER LEVEL
ADJUSTMENT
ROD
FLUSH
VALVE
PARTIAL
FLUSH
ADJUSTMENT
FULL
FLUSH
ADJUSTMENT
BAYONET
RELEASE
PUSH
BUTTON
VALVE
SEAT
SILICONE
SEAL
TOP
ARM
NIPPLE
REFILL
TUBE
Diagram 1
PARTS FOR WATER
CONNECTION
(SEE STEP 9)
CONE WASHER
THREADED
SHANK
SHANK
WASHER
COUPLING NUT
(HAND TIGHT ONLY)
FILL
VALVE
FLOAT
CUP
CRITICAL
LEVEL MARK
("C.L.") MUST
BE 1" ABOVE
OVERFLOW
PIPE
LOCK NUT
SET WATER
LEVEL HERE
ADJUSTMENTS
a. Adjust water level. Water level should
be adjusted to level indicated on tank by
adjusting float cup.
See Step 11 for water level
adjustment method.
b. Flush Valve Setting Adjustments:
• To remove Flush Valve, apply slight
downward pressure and twist it until the flush
valve disengages from the bayonet.
• To reinstall Flush Valve, reverse the above
procedure making sure the blue (Small Flush
Button) will line up with the Small Flush
Button with 3 dots on the Tank Lid.
Small Flush Button (with 3 dots) for liquid waste.
1.0 gal/flush
3.8 L/flush
Large Flush Button (with 9 dots) for solid waste.
1.6 gal/flush
6 L/flush
TIPS:
If the flush doesn’t flush properly, after eliminating other causes, remove
the tank lid and directly push the flush button in the tank. If the flush
works you will need to adjust the push button mounted on the tank lid
with the settings as follows:
1. Turn the lid upside down.
2. Loosen the black plastic lock nut.
3. Adjust the white threadrod one turn counterclockwise.
4. Re-tighten the black plastic lock nut.
5. Put lid back on tank and test. If it is still not flushing properly, repeat
steps 1 through 4 until the problem is resolved.
6. If one counterclockwise turn is too much and causes the flush valve
to stay open, adjust 1/2 turn clockwise and return to step 4.
WHITE THREAD RODBLUE THREAD ROD
BLACK PLASTIC
LOCK NUT
BLACK PLASTIC
LOCK NUT
Without Liner
Tank #
4349.216
4348.216
4339.216
Full Flush
Adjustment
Partial Flush
Adjustment
2
2.5
4
4.5
With Liner
Tank #
4349.516
4348.516
4339.516
Flush Valve
Setting
Adjustments
NOTE: All other settings will result in either
more or less water and is not recommended.