Installation Instructions

ManualsBrandsAmerican Standard ManualsBathH2Optimum 2-piece 1.1 GPF Single Flush Round Toilet in White

REMOVE OLD TOILET

a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.

b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!

c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.

NOTE: Mounting surface must be clean and level before new toilet is installed!

SAVE FOR FUTURE USE

CLOSET

FLANGE

CLOSET

BOLTS

7301416-100 Rev. M 4/18

FINISHED WALL

FINISHED FLOOR

SUPPLY

REQ'D.

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

Product names listed herein are trademarks of AS America Inc.

NOTE: Pictures may not exactly define contour of china and components.

ROUGHING-IN DIMENSIONS:

NOTE: Distance from wall to closet flange centerline must be as listed below:

A = 12" (305mm)

WAX RING

SEALANT

INSTALL WAX SEAL

Invert toilet on floor (cushion to prevent damage),

and install wax ring evenly around waste flange

(horn), with tapered end of ring facing toilet. Apply

a thin bead of sealant around toilet base.

POSITION TOILET ON FLANGE

a. Unplug floor waste opening and install toilet on closet flange so bolts project

through mounting holes.

b. Loosely install retainer washers and nuts. Side of washers marked "THIS

SIDE UP" must face up!

CLOSET

BOLT

NUT

TAPERED

WASHER

FLANGE

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure

this product is installed properly, please read these instructions carefully before you begin. (Certain

installations may require professional help.) Also be sure your installation conforms to local codes.

INSTALLATION INSTRUCTIONS

Siphonic Ultra-High Efficiency Two-Piece Toilets

H2Optimum

™

Single Flush Models 288AA / 288CA / 288DA

H2Option

Dual Flush Models 2886 / 2887 / 2889

INSTALL CLOSET BOLTS

Install closet bolts in flange channel

and slide into place parallel to wall.

RECOMMENDED TOOLS AND MATERIALS

Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure

Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level

Summary of content (6 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Siphonic Ultra-High Efficiency Two-Piece Toilets H2Optimum™ Single Flush Models 288AA / 288CA / 288DA H2Option® Dual Flush Models 2886 / 2887 / 2889 Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
PAGE 2
6 7 RUBBER GROMMET TANK MTG. BOLTS RUBBER GASKET BOLT CAP CLOSET FLANGE WASHER/NUT INSTALL TANK CLOSET BOLT WASHER NUT INSTALL TOILET a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor. ! CAUTION: a. Insert rubber grommets through holes in the tank then insert bolts through holes in the grommets. b.
PAGE 3
DUAL FLUSH MODELS ONLY FOR SINGLE FLUSH MODELS GO TO STEP 12 PUSH BUTTON ADJUSTMENTS b. Adjust water level. Water level should be adjusted to level indicated on tank by adjusting as follows: 1. Major water level adjustment - see Page 4 2.
PAGE 4
11 ADA DUAL FLUSH TRIP LEVER OPERATION Trip Lever Operation To select a Full Flush, push the Long Paddle fully and release. To select a Partial Flush, push the Short Paddle with Green Stripe fully and release. Long Paddle Short Paddle Rest Position Green Stripe To Replace Trip Lever Loosen the Blue Nut between the trip lever and housing by turning “clockwise” (NOTE: this is a reverse thread) and pull the housing away from the trip lever. Loosen and remove the White Nut by turning “clockwise”.
PAGE 5
12 SINGLE FLUSH MODELS ONLY WATER LEVEL ADJUSTMENT KNOB REFILL TUBE Adjust water level to level indicated on tank by turning water level adjustment knob to move float cup up or down.
PAGE 6
* for SINGLE FLUSH Models ONLY ** for DUAL FLUSH Models ONLY TROUBLESHOOTING GUIDE *** for ADA DUAL FLUSH Models ONLY Problem Possible Cause Does not flush Corrective Action a. Water supply valve closed. b. Supply line blocked. a. Open valve and allow water to fill tank. b. Shut off water supply, disconnect supply line and inspect all gaskets and washers. Reassemble. *c. Flush valve chain too loose or disconnected. *c. Readjust chain length as required. See Step 12. **c.