Installation Sheet

ManualsBrandsAmerican Standard ManualsBathtub Surrounds2946.BW.011

STUDIO

SHOWER & BATH WALLS

MODELS: 2946.BW & 2946.SW

755140-100

PREPARATION:

TOOLS:

TOOLS & MATERIALS REQUIRED....

Studio

shower walls are to be installed directly

over stud walls. Drywall is not required.

• Drill & Hole Saw or Sabre Saw

• Tape Measure

• Caulking Gun

• Pencil

• Square

• Level

A) Remove dry wall surface and ensure that

alcove is plumb and square. (Illustration 1)

MATERIALS:

• Acrylic/Latex or Acrylic/Silicone Sealant

• Galvanized (or corrosion resistant) flat head

screws 3/4" minimum length

• 2 x 4 lumber for additional wall studs as required

• Tub Surround Adhesive

• 1 x 4’s if installing shower doors

USE SHOWER WALL 2946.SW WITH SHOWER BASE 2946.STR or 2946.STL

USE BATH WALL 2946.BW WITH BATH TUB 2946.102 or 2946.202

Illustration 1

Installation for Model# 2946.SW

The studs should be located as shown to

properly support walls. Provide additional

studs where illustrated.

B) Identify your model number in the illustrations

which follow. Prepare studs as indicated.

(203mm)

10-1/2"

(267mm)

32"

(813mm)

(152mm)

12"

(305mm)

60"

(1524mm)

9-1/4"

(235mm)

9-1/4"

(235mm)

10"

(254mm)

10"

(254mm)

SAVE FOR FUTURE USE

Local building codes vary by location. Observe all local plumbing and building codes.

Unpack your new shower walls and inspect them carefully for damage. Verify that the walls are the correct size for your

installation. Refer to American Standard roughing-in information for specific dimensions for each model.

To ensure maximum performance and pleasure from this product, please follow the instructions and cautions.

BEFORE YOU BEGIN....

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed

properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be

sure your installation conforms to local codes.

NOTE: Take extra care in handling surfaces of the walls. Use only non-abrasive cloths to avoid scratching.

INSTALLATION INSTRUCTIONS

All product names listed herein are trademarks of AS America, Inc. unless otherwise noted.

Each alcove

stud must

be plumb

and square.

(Left hand shower base shown)

Summary of content (6 pages)

PAGE 1
INSTALLATION INSTRUCTIONS STUDIO® SHOWER & BATH WALLS MODELS: 2946.BW & 2946.SW USE SHOWER WALL 2946.SW WITH SHOWER BASE 2946.STR or 2946.STL USE BATH WALL 2946.BW WITH BATH TUB 2946.102 or 2946.202 Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
PAGE 2
PREPARATION: Installation for Model# 2946.BW The studs should be located as shown to properly support walls. Provide additional studs where illustrated. (Right hand tub shown) 60" (1524mm) 9-1/4" (235mm) 10" (254mm) 9-1/4" (235mm) 10" (254mm) 9" (229mm) 12" (305mm) 6" (152mm) 32" (813mm) 9-3/4" (248mm) IMPORTANT: C) Rough plumbing and fittings must be installed before walls.
PAGE 3
2 A) Position the three panels into the alcove. Lower each panel onto the shower base or tub to ensure that the panels fit properly in the alcove. Top Nailing Flange B) Mark the appropriate side panel (right or left) cutouts for plumbing fixtures. Refer to plumbing fixture installation instructions for hole dimensions and placement. Carefully locate, mark and cut holes using the properly sized hole saw. Attach fire retardant pad to the back of the panel per the instructions included with the pad.
PAGE 4
A) • Locate and drill a clearance hole in the center of the top nailing flange and centered on each stud (see arrows as shown). • Also drill four evenly spaced clearance holes on the front nailing flange on each side (see arrows as shown). B) Ensuring mating surface is square and plum (Fig. 2), install galvanized screws through each clearance hole and into the studs, securing the wall panel. C) Add a bead of sealant down the vertical corner of the back panel (Fig. 2).
PAGE 5
Continued: D) • Locate and drill a clearance hole in the center of the top nailing flange and centered on each stud (see arrows as shown). • Also drill clearance holes in the front nailing flange on each side panel at approx. 12" intervals, centered on the flange (see arrows as shown). • Install galvanized screws through each hole and into the studs, securing the wall panel.
PAGE 6
8 A) After greenboard is installed, apply finished sealant bead to all edges and joints. Follow sealant manufacturers’ recommended cure time. B) Make connections to supply and drain lines. POST INSTALLATION CLEAN-UP Remove all construction debris. Tile grout can be removed with a wooden popsicle stick or tongue depressor. Do not use wire brushes or any other metal implement on surface. Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent.